I have one cisco 2851 router and one watchguare firewal currently being used as the main router. I want to connect the cisco as a secondary router on the same network.
View 10 Replieshow to cofiger a network printer in a network, i am using a bsnl broadband connection with user id and psw. all systems are getting internet but printers are not connecting to print.
View 1 Replies View RelatedI am planning to put an internet cafe in my place, i want to buy 20 units of PC to start the business. how to set-up or configure the PCs, How to use router and how to configure the PCs to activate the network.
View 4 Replies View Relatedhow to connect 2 routers on different lan
View 3 Replies View Relatedi have a pppoe connection coming through ethernet line. i.e i need to use dialer that i have created on the desktop..and i have bought a new Linksys E1000 router v2.1..now my problem is that1) After entering all the settings correctly my router worked for 3 days after that the net is not working.i.e it cannot connect to the internet keeps giving the error cannot get IP from PPPOE(i have connected my router in pppoe mode and use the router status page to connect and disconnect)I have also updated the router to the latest firmware 2.1.01 and after that the problems have started.My Net works if i directly plug the Ethernet cable in the PC.the problem starts when i connect it to my router.
View 3 Replies View RelatedI have a BSNL wifi modem WA3002g4 . i am unable to configure the modem192.168.1.1 site does not respond
View 1 Replies View RelatedI have installed a DIR615 N Router and can get onto the Internet on the PC, but when I type in the device IP address it comes up with an "error" message so I cannot configure it.
View 6 Replies View RelatedI remember long ago I was upto some trial and error with my router and I ended up in changing some ip that I didn't know about that time, now when I was trying to forward some of the ports. I addressed the computer to 192.168.1.1 (as this was my ip that time I remember and on the box its written too) but it didn't respond, then I remember that I have changed this ip to something else and now I can't remember this.
View 7 Replies View Relatedi have one machine have 2 Ethernet devices and i need to connect this server to different 2 network with 2 different gateways (192.168.2.x "vpn network" and 192.168.1.x "adsl network" )so if any other one need to connect this ftp server can connected from vpn or adsl
View 1 Replies View RelatedThis is the situation in our Lab.We have one telephone line with broadband connection and a system which is connected to a modem to use this broadband facility. Recently we have taken two static IPs over this connection for a project work.Now what I want to know is, how to configure these static IPs, so that I can connect two systems (each one to one static IP) to use these static IPs and continue to access the internet in the 3rd (already present) system.
View 7 Replies View Relatedhow do i configure cisco switch Edge
View 1 Replies View Relatedi am adding a wired router,during configuration i must choose between PPPoE,Dynamic,Static connection type. i have broadband cable isp
View 2 Replies View Relatedi have a ZyXel prestige 650H-31 Model # router and i'm not able to go on to configuration page of the router i tried 192.168.1.1 several times, even after system reboot and router reset, but of no use. I've a wire connection with desktop (RJ-45 port) not USB AND MY PPPoE lights never lit. originally when i entered the gateway 192.168.1.1 it asked me for username & password, since i didn't have the password at that time i tried to reset the router but after that when ever i entered 192.168.1.1 in the browser it never came up with the option to enter user name & password. I've checked all the wires are also connected. I tried prompt command and it showed that timed out thrice and then sent= 4 received= 0 lost= 100%. I had D-Link router prior to it and later connected the D-Link router an i was able to get connected to net and browse normally.
View 1 Replies View Relatedhow to configure VLAN on ALLIED TELESYN AT 8024M?
View 1 Replies View Relatedi have a LAN network between several pc's connected with several switch's and connected to Thomson SpeedTouch 510 DSL Router its ip address is 10.0.0.100 subnet 255.0.0.0 and the router dont give auto ip to the PCs i have to issign it manually to the PCs "static ip".I bought the acer android recently so i bought a tp-link td-w8901g wireless router to act as an access point so i connected the 2 routers to each other by LAN and gave the tp-link an ip address 10.0.0.12 subnet mask 255.0.0.0 so it will be the same ip range of the speedtouch and setuped the tp-link router to fit my isp configeration it worked at first but i had to reset the router so i did the same configuration i did before but didnt work and i cant access the internet using the android or the wireless but when i connect the phone to the tp-link and unplug the speedtouch the wireless works so theres no any problem with the router?
View 1 Replies View RelatedI have a Hawking 300N and I have misplaced my disk and I neing walked through this to have it set back up. I hooked it all up correctly and it says no internet connection
View 1 Replies View Relatedi am unable to configure my netgear router with my clear modem
View 1 Replies View RelatedI have a WN3000RP WiFi Range Extender but I cannot seem to find out how to connect to it on my Windows 7 Desktop computer to configure it. My Router is a Netgear Wireless G RouterWGR614 v9
View 7 Replies View Relatedi recently had att u vesre installed at my house with a 2 wire 3801 router/ modem but i cant get my xbox 360 online. how to configure the router for the xbox 360 so i can play xbox live.
View 1 Replies View RelatedI want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
View 3 Replies View RelatedI have a bit of an unusual networking situation here in my home and need proper configuration, so I stop losing my web connection on a daily basis.The reason I'm forced to have the 2nd router is that my wife telecommutes and the 1st (primary router) is provided by her company. For whatever reasons, her company will not allow the wireless radio in their router to be turned ON - which forces me to add the 2nd wireless router for our 3 computers that require wireless access.
1 - Since the primary router has DHCP enabled, I am assuming that I should Disable DHCP on my wireless router. Am I correct?
2 - What other settings on the wireless router do I need to pay particular attention to in this situation?
Our Motel has a new CenturyLink DSL Wifi Modem at the office desk, and I'm trying to get wifi to all customers via (3) Linksys WRT110 wfi routers that are in the attic. How do you configure the routers so all put a wifi signal out with the same network name ? I keep getting limited connections & etc...
View 1 Replies View RelatedIn my house I have a BT Business Hub wireless router at one end of my house. I am looking to extend the wireless range of my network into the kitchen at the other end of the house, which is a rather large distance away. The house is 200 years old with large corridors and thick walls. There is absolutely no wireless range from about halfway between the office and kitchen. I initially tried two powerline adapters which did not work. Having spoken with an electrician who carried out a rewire on the house, I have been advised that the two areas are on a separate ring main.I considered using two wireless range extenders, but have been told that the signal is halved for each extender that I use.So, I have had the idea of trying to use two DSL routers at each side of the house. There is a phone point in the office and also in the kitchen, where the second router would plug into. These are both on the same telephone line.
View 4 Replies View RelatedI have 2 PC's connected to router.The router is connected to internet.The question is how to get the PC's in the outside network into router?if I connect 1 PC directly to internet I can find and share files with my friend pc ( my computer> network)but when I connect Router in between I cant find any PC's(I find only my PC's) in network.
View 11 Replies View RelatedMe and my friend hucked up a net wort from our houses (bout 50 feet away) he is brodcasting wirelessly, and my desktop is not wireless so i used a laptop to conect to his and conected a hard line to my router and conected it to my pc and bridged the conections.my router starting ip was fixed to 192.168.2.1 and his is set to 192.168.1.1 so itll conect and i turned off my dhcp ip (his is on). my wireless on the router is off. It worked and i have acess to the network and the internet but every once in a wile i get DCed with a windows error saying my ip for my pc is the same as another computer on the networkIs there a way to fix this? did I hook them up right cuse I am not that good a networking
View 4 Replies View RelatedI need configuring my N900 router to be able to use Microsoft's Remote Desktop Connection to get into my computer from a client's location. I also want to be able to host websites I'm developing so my clients can see the changes before publishing to their website. I have not been able to find anywhere what settings to set to what in order for these two things to be available to me.
View 2 Replies View RelatedIf your wireless indicator is flashing red when you discover the smurf, it can mean that someone has tried to logon with an incorrect password. this is not necessarily an attack, it could be someone you have allowed access too, who has forgotten the password? In this case entering the correct password will solve the problem.However putting your own MAC address into the filter will simply block your own machine.
View 6 Replies View RelatedFor my work I am looking to create wireless capabilities to remote locations. To do this we are using a standard modem/router that is connected to an Engenius (802.11b/g) wireless outdoor radio connected to a dish antenna. We are able to go to locations (3+km) and then with a corresponding receiving antenna (using LoS), receive the Internet and connect both to computers at the transmitting point as well as to the WWW. The problem exists is that we want to employ a series of routers at the receiving end that would be able to carry the transmission to a different location (relatively close), due to the fact that some of the locations do not have line of sight to the antennas. We are using Encore routers, model # ENHWI-N3. When we connect the radio's Ethernet into the routers WAN reciever, we can connect to the Internet with a computer. The problem exists is we want to pass that connection over to a second router (R2). This connection is done when the routers are on access points set to a WDS function with R1 having R2's mac address and vice versa. Both routers are set to channel 1. Even when the routers are seperated by distances >50m a computer plugged into R2 can see a computer plugged into R1. Files can be transferred between the 2 computers wirelessly at speed around 3 mbps. However computer 2 on R2 can not connect to the WWW. This router features a spot that lights up if it has Internet access and R1's is lit up but R2's is not. How do we transfer the Internet and not just a LAN from R1 to R2 so it can be accessed further away from the point of the radio and antenna equipment. This setup has also been used where R2 is hardwired to R3. At R3 we change the channel to 11, and then connect through that with mac addresses wirelessly to 4th router. If comp is in R4 and far away it can still access and file share from comp at R1.*edit the ip address for the routers exist all on 192.168.1.xxx If the 3rd number is different between routers would this make a difference?
View 1 Replies View Relatedeverything was all good, my brother went crazy and unplugged everything.it effects our house phone too, that could be the problem.i just dont know what wires went where. all the wires are the same color.but i know which is which. just again, dont know where.i would like to get it done before he gets home later on.
View 1 Replies View RelatedGot two pc's, two routers and one switch, and two serial cables and I want to create a network.
View 4 Replies View RelatedI have 192.168.2.1 and 10.10.0.1But i cant connect to 10.10.0.1 network from 192.168.2.1 network. What should I do to connect that both are same network I have a Linksys Router.
View 2 Replies View RelatedI have a D-Link DIR -655 wireless router connected to my Time Warner Cable modem upstairs. Downstairs I have a PS3, Wii, Logitech Revue and a HP laptop. I get low signal strength downstairs(many walls) and would like to run an Ethernet cable downstairs to my devices. What hardware do I need downstairs to hard wire those devices? Not sure if router or switch and what kind. Do I need to make any changes to my existing D-Link wireless router? I want to keep the wireless available for cell phones and the HP laptop.
View 3 Replies View RelatedAs per settings menu, I tried to give it an IP address but the new address is not accessible for further configuration. When I connected to the router it status changes to "unidentified network".
My primary network address range is 192.168.1.1 to 192.168.1.10. So I gave address to belkin as 192.168.1.100. But I can not access this address from both primary and belkin network.