Routers / Switches :: D-Link And Linksys Routers Plus Modem Connection
May 26, 2011
everything was all good, my brother went crazy and unplugged everything.it effects our house phone too, that could be the problem.i just dont know what wires went where. all the wires are the same color.but i know which is which. just again, dont know where.i would like to get it done before he gets home later on.
I have a big 2 floor house .I would like to use 3G connection using USB type of modems,like vodaphone or MTS. which router to be used so that I can get good connectivity on both floors. NOTE- I do not want to use cabled internet coonections.
In my office we have concrete walls and very limited wiring. The way it is set up is we have a Verizon DSL Modem that comes in then I have a router with it that splits the signal to 4 other routers that each split the signal 2 to 3 more times. I have to use routers so that it assigns IP addresses.I bought a new D-Line N300 Wireless router with USB imput. I want to attach my Home Media Network Hard Drive Cloud edition to the 1st router (attached to the modem) and then share the data off that hard drive with everyone connected to the sub routers.
My Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
I have an ARRIS modem supplied by Comcast cable. I have an hp pavilion x1958 and want to run internet service to a secondary computer from the same modem. And I don't have money to buy a router. How can I do this the cheapest way?
Currently I have 2 different modem running in my working area which is modem A and modem B. Whenever user from Modem A(192.168.0.1) or Modem B(192.168.0.10) would like to print or scan something using the shared printer, I need to manually plug the cable into either Modem A or Modem B depends on the network the user are currently using.How I do previously is only set DHCP on Modem A and disable DHCP for modem B so that Modem B will share DHCP assigned by Modem A. Both modems connect to the same Switch with the printer cable so both network user can use it together.But the problem now is I have to enable DHCP for both modems and causing the previously method can't be use anymore. So is there any other way that I can link both Modem A and Modem B with each assign different DHCP to link with 1
The modem Time Warner gave me several years ago was dying, I took it in, they gave me a Cisco modem, I plugged it into the computer, works fine, so then I plugged it into my airlink 101 wireless router, the computer recognizes the router but says there is no internet access, i.e. the modem and router are not communicating. Why would change of modem cause lack of communication with the router, is there something different about modems now compared with roughly 5 years ago? And what can i do to fix it so i can have wireless access again? If it matters, I have no protection on my wireless (because I never figured out how).
I connect to the internet through a Thomson TG585 v8 modem. When I log in to the modem's IP (192.168.1.254?) through a browser, I only get one task available, that is "Check connectivity for this internet service". As far as I know, I should have some management options, like for example to block websites, to limit internet service for certain devices etc... Does anybody knows why I don't have these options? Could it be a restriction from the Internet Service Provider?
Dell dimension 2400 XP home. Connects fine to old linksys g router.With new qwest dsl modem/router get IRQL not less than or equal as soon as I click on connect .Blue screen stop and must reboot.Qwest router works fine with my lenovo lap top. Win 7.
Trouble connecting to the internet wireless with Motorola SB6120 and Linksys WRT120N. The modem works directly with LAN but as soon as I try to use the router, I can connect to the network but no internet is available.
I just got a DSL Modem router (DSL 2750U) which has DSL input for internetconnectivity.My internet service provider provides RJ45 Cable which needs LAN input socket on a router for internet connectivity. How do I connect?
I am trying to connect a Netgear wirless router to my cable modem. I have followed the instructions on the set up wizard but it fails to get a connection with the IP and DNS info I provide.I got the IP address info by connecting intially direct from the modem to the PC and then went to Run CMD and type ipconfig /all. I then started the set up wizard and followed the instructions, turning things on in specific order etc. After input the IP and DNS info it reports an error and tells me to check the address information is correct.My internet is a static IP connection (so it tells me and the IP information doesn't change).
Adding ports to my Fairpoint provided Westell 7500 Rev D DLS modem router which has only 4 RJ45 ports. Bought a Linksys SE2500 gigabit smart switch but it doesn't assign IP or pass on router assigned IPs. Can't get ASSISTANCE from Fairpoint [successor to Verizon] configuring router or any advice on other ways to get more wired devices on LAN.For speed in backups I'd like 3 devices to be able to communicate at giabit speed Want to have an NAS and 2 Win7 Ultimate computers on smart switch, 3 other wired devices [WinXP, AT&T Cell tower, & DirectTV whole house SWM interface] and wireless on the router. 1. Are Fairpoint specs for DSL published so I could get another DSL modem router instead of the Westell or is it better to configure Westell as a router only and use a new to be acquired router with or without the existing or a new gigabit switch. I have a DI-624 from the pre-DSL Hughesnet satellite days.2. Are there less smart switches which would work better and let router assign the IPs?3. If this is too complex for me, can you recommend a remote access consultant to walk me through this for a fee?4. I'm 82, have been in computing since 1960, mainly in on-line end user environment mbut don't know the bridging, PPP PPoE differences, and implementation or configuration details of current hard and software except as a user.
show me how to hook up a Belkin G Router to a symomatic Atlantics modem its already from the wall hooked up to my moms desktop and i want it also on my desktop.
my computer will connect wired to internet and can find the wireless connection but wont connect. my wireless icon flashes intermitently and my mobile will work via wifi. do i need a new router this one is a G wireless Modem router Belkin had it for about 4 years?
how do i create 2 networks using 1 cable modem and 1 router and i would like to add a firewall thinking of using xywall usg20 for the firewall..... the issue is i have a small business with 1 point of sale and1 back office computer.(network1) and i would also like to use an air port wifi to offer wifi to my cleints on a seperate network(network2) not allowing access to network1 and i want a firewall on network 1 to protect the back office and pos system
My main networking device is the Ericsson T073G HGU ONT, and when I am connecting to the network through the Ethernet there are no problems. However when I connect my Belkin F6D4230-4 router to it (through cable) my router cannot recognize the modem.I have tried literally everything.
Have one switch and network.PC number one have win98 and network adapter and connected to the switch.PC number two have winXP and network adapter and connected to the switch same as win98.Network works on win98 and winxp they see each other.internet working on winxp but dont work on win98
Ok, my roomate is hogging the bandwidth on our shared router downloading junk. I'm not sure if he's using a torrent, but just in case he is here is my question:How do I turn off the ports for torrenting on my qwest pk5000 modem? Is there anything else I can do that would work as well?My friend reccommended I turn off every port after 9000 or something.
My computer is not wireless so I have needed a wireless router from Time Warner. Directions tell me to connect to my computer. Will that solve the fact that my computer is not built in wireless?
My modem is an Arris Model TM502GI don't remember how to set it up. That is what cable goes where & is there anything to do on the PC With WiFi for it to connect with my router?I am 70 years old with a limited knowledge of computer and other electronic gadgets.
I reset the f5d9321 router and no connection with modem, power cycled the modem and router and still no connection with the modem. Pc and laptop can connect to internet by connecting to modem. The router worked fine 3 days earlier.