I just got a DSL Modem router (DSL 2750U) which has DSL input for internetconnectivity.My internet service provider provides RJ45 Cable which needs LAN input socket on a router for internet connectivity. How do I connect?
I want to connect 2 desktop computers by wire to my broadband. The inlet is 20 metres downstairs. Should i use RJ11 to reach the Router upstairs, then connect with 5 metres RJ45, OR run two RJ45 cables 25 metres with Router near socket downstairs.? Would there be any degredation in either cable.?
My Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
my computer will connect wired to internet and can find the wireless connection but wont connect. my wireless icon flashes intermitently and my mobile will work via wifi. do i need a new router this one is a G wireless Modem router Belkin had it for about 4 years?
can I use a RJ45 splitter with 2 female ends to run the internet off the same modem for 2 computers?ie:going from the ethernernet port off the back of my modem,install the splitter there and then send 2 diferant cables to 2 computers to have access to the internet with both compputers
Is it possible to use ADSL Wireless router (one with RJ11 WAN in) to connect to cable net? If not is there any which can allow me to connect to cable net in future if in case I change to cable net ISP.
Have one switch and network.PC number one have win98 and network adapter and connected to the switch.PC number two have winXP and network adapter and connected to the switch same as win98.Network works on win98 and winxp they see each other.internet working on winxp but dont work on win98
we are experiencing truouble to connect a RV120W Router using an E1 link with RJ45. Everything seems ok when the router was configured with a static IP, also we can establish an IPSec tunnel, but if we try to use RDesktop through the tunnel, or email services with POP3, after a few minutes the router restarts, or loose any signal wireless, ethernet and WAN; also it becomes hot.
Trouble connecting to the internet wireless with Motorola SB6120 and Linksys WRT120N. The modem works directly with LAN but as soon as I try to use the router, I can connect to the network but no internet is available.
I am trying to connect a Netgear wirless router to my cable modem. I have followed the instructions on the set up wizard but it fails to get a connection with the IP and DNS info I provide.I got the IP address info by connecting intially direct from the modem to the PC and then went to Run CMD and type ipconfig /all. I then started the set up wizard and followed the instructions, turning things on in specific order etc. After input the IP and DNS info it reports an error and tells me to check the address information is correct.My internet is a static IP connection (so it tells me and the IP information doesn't change).
My main networking device is the Ericsson T073G HGU ONT, and when I am connecting to the network through the Ethernet there are no problems. However when I connect my Belkin F6D4230-4 router to it (through cable) my router cannot recognize the modem.I have tried literally everything.
everything was all good, my brother went crazy and unplugged everything.it effects our house phone too, that could be the problem.i just dont know what wires went where. all the wires are the same color.but i know which is which. just again, dont know where.i would like to get it done before he gets home later on.
In my office we have concrete walls and very limited wiring. The way it is set up is we have a Verizon DSL Modem that comes in then I have a router with it that splits the signal to 4 other routers that each split the signal 2 to 3 more times. I have to use routers so that it assigns IP addresses.I bought a new D-Line N300 Wireless router with USB imput. I want to attach my Home Media Network Hard Drive Cloud edition to the 1st router (attached to the modem) and then share the data off that hard drive with everyone connected to the sub routers.
Not too much networking savvy - but here goes. Want to use router as local lan - no wireless. When router is connected to laptop via RJ45 I loose my ability to connect to sites via browser. IPconfig shows wireless adapter at 192.168.1.3. When router is attached it's ip is 192.168.1.1. Disabled the wireless in the settings but no dice. When the router was used with DSL it was set at PPPoE but now that I'm just using it locally not sure whether it should be DHCP or Static or other.
I have 4 computers on LAN using a router and I cannot see eachother, don't know how to configure the PCs. The router is set on DHCP for LAN, the PCs are using Windows 7 and can connect through the internet the router is providing (4 dells) but don't know how to set the computers to see eachother and to share files.
I try connecting to my Linksys wireless N router's setup but it doesnt even find the "site". I have tried pinging the router and i get no response, i have restarted the router and everything, It has never done this before.
I have 3 laptops, 2 tivos, wii, ipad, i touch, etc..... how many items can connect to one router without drops outs? My internet keeps dropping off since my last device connected to my wireless home network and we have to keep hitting the reset button. Do different routers support more devices than others?
I have an Iball Baton Router. I am not able to connect to it from my PC. However, I am able to connect to the router from my Laptop.I have tried isconnecting and renewing the ip. Can see that ip (192.168.1.102) is issued to my PC and can ping to the same. But, do not get any reply when I ping to the gateway (192.168.1.1 - ip for the router). My OS is Windows 7 64 bit.Let me know if you need any more information
I have an ARRIS modem supplied by Comcast cable. I have an hp pavilion x1958 and want to run internet service to a secondary computer from the same modem. And I don't have money to buy a router. How can I do this the cheapest way?
Currently I have 2 different modem running in my working area which is modem A and modem B. Whenever user from Modem A(192.168.0.1) or Modem B(192.168.0.10) would like to print or scan something using the shared printer, I need to manually plug the cable into either Modem A or Modem B depends on the network the user are currently using.How I do previously is only set DHCP on Modem A and disable DHCP for modem B so that Modem B will share DHCP assigned by Modem A. Both modems connect to the same Switch with the printer cable so both network user can use it together.But the problem now is I have to enable DHCP for both modems and causing the previously method can't be use anymore. So is there any other way that I can link both Modem A and Modem B with each assign different DHCP to link with 1
I have a WD, 1TB, external harddrive with a USB connection and would like to know if it is possible to get a USB hub with an ethernet connector to connect into the back of my router. Is it possible to do this? If so, what will I need to do? Will I need to give the external drive a static IP address, then partition it?
I changed my netgear wireless router password and now my laptop will not connect to the router or to the internet. It has no popup to put the new password. I have no problem logging on with my phone...just the laptop.