My Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
everything was all good, my brother went crazy and unplugged everything.it effects our house phone too, that could be the problem.i just dont know what wires went where. all the wires are the same color.but i know which is which. just again, dont know where.i would like to get it done before he gets home later on.
I have a working VPN with a WRVS4400N Wireless N VPN Router. There is a Windows XP computer on the network with a static IP address and a shared folder that I need to access with QuickBooks across the VPN.I can connect to the router; but only doing that is of little use. Once my VPN connection is made,how do I find the computer on the other side and map a drive to it or get it with QuickBooks? I need to do this with a Windows Vista Computer and a Windows XP computer at remote locations. Windows Vista seems to be different than XP in that it will not let me type a network address in Explorer without adding an HTTP://. Network places does not seem to work either.
In my office we have concrete walls and very limited wiring. The way it is set up is we have a Verizon DSL Modem that comes in then I have a router with it that splits the signal to 4 other routers that each split the signal 2 to 3 more times. I have to use routers so that it assigns IP addresses.I bought a new D-Line N300 Wireless router with USB imput. I want to attach my Home Media Network Hard Drive Cloud edition to the 1st router (attached to the modem) and then share the data off that hard drive with everyone connected to the sub routers.
I got a static ip from my isp. I set up my static ip manually through my linksy router. I need the static ip to connect to a private network for my new job but cant connect to that network. I went to whatsmyip and found that my old dynamic ip is still showing up externally, it looks like my ip4 is using the dynamic as a preferred. My question is do i need to manually change the network connection on my LAN and wireless connection under ipv4 to change it from automatically obtain TO use the following address and put in my static? And do I have to change the DNS also? I am on a home network with one desktop on vista home premium and laptop windows 7.
I bought a new laptop today, unfortunately, it doesnt have a Firewire port and i want to use it for video editing.But i figured no problem really, i'll just capture on my desktop that i have been previously using to edit on, using Premiere pro to edit, but HDVsplit to capture, and then transfer the files over to the laptop using a USB or possibly trying to setup a home network.But when transferring files from the desktop onto the laptop via the router using ethernet cables, the speed is about 250 kb/s and when its the other way around, from the laptop to the desktop, the speed is 10 MB/s! I really need to find away to speed this up as the overall files i want to transfer are over 5GB.You can read a bit more about it here: [URL]
I have an ARRIS modem supplied by Comcast cable. I have an hp pavilion x1958 and want to run internet service to a secondary computer from the same modem. And I don't have money to buy a router. How can I do this the cheapest way?
Currently I have 2 different modem running in my working area which is modem A and modem B. Whenever user from Modem A(192.168.0.1) or Modem B(192.168.0.10) would like to print or scan something using the shared printer, I need to manually plug the cable into either Modem A or Modem B depends on the network the user are currently using.How I do previously is only set DHCP on Modem A and disable DHCP for modem B so that Modem B will share DHCP assigned by Modem A. Both modems connect to the same Switch with the printer cable so both network user can use it together.But the problem now is I have to enable DHCP for both modems and causing the previously method can't be use anymore. So is there any other way that I can link both Modem A and Modem B with each assign different DHCP to link with 1
my modem is working, I have two computers on the router plus my wireless is working.I connected my cable that was going from the modem to the router directly to the computer and it still says "network cable unplugged"sis 900 based PCI fast internet?
I have CentOS and the application I am running does not listen on 192.168.1.5 (Private IP address). Right now I have connected using bridge mode and I can see in my network configuration-> ppp and eth0. PPP has public IP and eth0 has private IP. Is there any way that I can get public ip assigned to eth0? I do not have Static IP, I want to use the public dynamic IP assigned by my ISP to use in eth0 interface.
Had laptop connecting wirelessly perfect with no problems. We then added another laptop and PSP 3 to the house hold. Any of the 3 devices will connect to the internet via wireless but ONLY one at a time. If you are connected with one and turn on one of the others it will kick the one off that you were on and only 1 device can use wireless at a time?
The modem Time Warner gave me several years ago was dying, I took it in, they gave me a Cisco modem, I plugged it into the computer, works fine, so then I plugged it into my airlink 101 wireless router, the computer recognizes the router but says there is no internet access, i.e. the modem and router are not communicating. Why would change of modem cause lack of communication with the router, is there something different about modems now compared with roughly 5 years ago? And what can i do to fix it so i can have wireless access again? If it matters, I have no protection on my wireless (because I never figured out how).
I connect to the internet through a Thomson TG585 v8 modem. When I log in to the modem's IP (192.168.1.254?) through a browser, I only get one task available, that is "Check connectivity for this internet service". As far as I know, I should have some management options, like for example to block websites, to limit internet service for certain devices etc... Does anybody knows why I don't have these options? Could it be a restriction from the Internet Service Provider?
I have a big 2 floor house .I would like to use 3G connection using USB type of modems,like vodaphone or MTS. which router to be used so that I can get good connectivity on both floors. NOTE- I do not want to use cabled internet coonections.
I want to setup a static ip address for a h.264 network dvr ,however my desktop computer is out of order, that is connected direct to router,is it possible to use my wireless laptop to setup the router,or will I have to connect the eithernet cable to the laptop.
After a power failure nothing could connect to the internet anymore. I called MTS (ISP provider) and they had me change some setup on my PC. Now my PC connects to the internet, but nothing else will connect (X Box, WII, iPods, Laptop). They were connected wireless before the power outage through my router. MTS said they are only responsible for ensuring their model works, not routers.I have checked some router settings. It is set for DHCP with 50 users.
Dell dimension 2400 XP home. Connects fine to old linksys g router.With new qwest dsl modem/router get IRQL not less than or equal as soon as I click on connect .Blue screen stop and must reboot.Qwest router works fine with my lenovo lap top. Win 7.
Trouble connecting to the internet wireless with Motorola SB6120 and Linksys WRT120N. The modem works directly with LAN but as soon as I try to use the router, I can connect to the network but no internet is available.
I just got a DSL Modem router (DSL 2750U) which has DSL input for internetconnectivity.My internet service provider provides RJ45 Cable which needs LAN input socket on a router for internet connectivity. How do I connect?