Routers / Switches :: Bsod When Connecting To Qwest Dsl Wifi Modem
Feb 5, 2012
Dell dimension 2400 XP home. Connects fine to old linksys g router.With new qwest dsl modem/router get IRQL not less than or equal as soon as I click on connect .Blue screen stop and must reboot.Qwest router works fine with my lenovo lap top. Win 7.
Ok, my roomate is hogging the bandwidth on our shared router downloading junk. I'm not sure if he's using a torrent, but just in case he is here is my question:How do I turn off the ports for torrenting on my qwest pk5000 modem? Is there anything else I can do that would work as well?My friend reccommended I turn off every port after 9000 or something.
i have an Iomega Prestige Desktop External Hard drive usb 2.0.I also have a quest-centurylink ZyXEL modem model #PK5000Z.I would like to connect the iomega to the modem. However, I don't see a usb port on the modem.
I have a Cisco 678 connected to my ISP (Qwest) using DHCP. This is connected to a Linksys WRT54g router. I also have a home server running for remote access to some files and media streaming. I just installed security cameras that I wish to monitor remotely via the internet.I can access my home files over the internet with no issue. However I am unable to access my cameras using the internet. Looking at my router incoming log, I see my request arriving, but I never get to the DVR attached to the camereas for remote viewing.I enabled bridging on the Cisco 678 but this did not solve the issue.
Currently I have 2 different modem running in my working area which is modem A and modem B. Whenever user from Modem A(192.168.0.1) or Modem B(192.168.0.10) would like to print or scan something using the shared printer, I need to manually plug the cable into either Modem A or Modem B depends on the network the user are currently using.How I do previously is only set DHCP on Modem A and disable DHCP for modem B so that Modem B will share DHCP assigned by Modem A. Both modems connect to the same Switch with the printer cable so both network user can use it together.But the problem now is I have to enable DHCP for both modems and causing the previously method can't be use anymore. So is there any other way that I can link both Modem A and Modem B with each assign different DHCP to link with 1
I just got a DSL Modem router (DSL 2750U) which has DSL input for internetconnectivity.My internet service provider provides RJ45 Cable which needs LAN input socket on a router for internet connectivity. How do I connect?
I am trying to connect a Netgear wirless router to my cable modem. I have followed the instructions on the set up wizard but it fails to get a connection with the IP and DNS info I provide.I got the IP address info by connecting intially direct from the modem to the PC and then went to Run CMD and type ipconfig /all. I then started the set up wizard and followed the instructions, turning things on in specific order etc. After input the IP and DNS info it reports an error and tells me to check the address information is correct.My internet is a static IP connection (so it tells me and the IP information doesn't change).
My modem is an Arris Model TM502GI don't remember how to set it up. That is what cable goes where & is there anything to do on the PC With WiFi for it to connect with my router?I am 70 years old with a limited knowledge of computer and other electronic gadgets.
My Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
I have a problem connecting wifi router(airlive wt-2000r) to my ADSL modem(webstar epc2203ed2.0) using utp patch cable. When my PC is connected straight to the ADSL modem everything works like charm. But when I connect modem with wan port on the router and router with my PC I get no internet access. The network shows as unidentified network and win7 troubleshooter says: Default gateway not available. Connecting them two devices seems pretty simple and I dont think I am doing anything wrong so what could be the problem?
everything was all good, my brother went crazy and unplugged everything.it effects our house phone too, that could be the problem.i just dont know what wires went where. all the wires are the same color.but i know which is which. just again, dont know where.i would like to get it done before he gets home later on.
I have two wireless modem/routers - a Ugo Mach5 CN458 and a Swift 4G - in two branches of my company that are distance apart and i want to connect them together so that they can be on the same network and workers in both branches can communicate and share files.
In my office we have concrete walls and very limited wiring. The way it is set up is we have a Verizon DSL Modem that comes in then I have a router with it that splits the signal to 4 other routers that each split the signal 2 to 3 more times. I have to use routers so that it assigns IP addresses.I bought a new D-Line N300 Wireless router with USB imput. I want to attach my Home Media Network Hard Drive Cloud edition to the 1st router (attached to the modem) and then share the data off that hard drive with everyone connected to the sub routers.
I am connecting to internet via motorola modem which gives me approx 6 Mbps download speed when I test it with both speedtest.net and speakeasy.net. Any device that I use connected wirelessly to my Belkin N300 router only acheives about 1.3 MBps of download speed. Is this just the way it is or could I have a router configuration issue or something else?
The router recognizes the Sierra 312U modem but does not connect to Telstra. The modem is on a monthly plan (not pre-paid) and I have tried APN settings such as internet.telstra and internet.bigpond. The configuration is set to manual and the correct user id and password have been entered. explain the "daemon.err rc: start -1 port.... fail (-8)" in the log? 312U sierra model supposed to be compatible with SRP500s. Any other settings I should try?
I have a building with 30+ pc's, printers and cameras. I do not have a "server" setup, however I want them to be connected to the T1 line comming into the building for internet as well as file sharing, etc.Currently, I have the T1 line connecting to as Linksys E3000 wireless router. From there I have a cable connected to the wireless router (it has 4 ports also) and then going to a Netgear FS524 (24 Port 10/100 MBPS Fast Ethernet Switch) via port number 24. I then have another CAT5 cable connected to a port on this switch, extending to a D-Link DES-1024D (another 24 Port, 10/100 switch)I then have the 30+ CAT5 cable coming into all three of said devices... No then, I get Internet connection on all units, the problem is that I cannot see all of the devices.
I have an ARRIS modem supplied by Comcast cable. I have an hp pavilion x1958 and want to run internet service to a secondary computer from the same modem. And I don't have money to buy a router. How can I do this the cheapest way?
I just moved into an apartment where the internet is being provided to me via wifi (open). The landlord doesn't have a private network, he is with me. What I'm was curious about is if it is possible for me to use a second router to create a secured network for all my devices? My thought would look like this: ISP>Landlords Router>wireless>MyRouter. I know you can have private and public wifi but the two routers have to be connected. I haven't talked to him about the fact that he needs to secure his router mainly because we never cross paths.
my Netgear WPN824v2 router won't connect to the internet. It stopped connecting after a power outage 4 days ago. All local connections work fine. wireless unaffected. I tried a different router, but it wouldn't work either. Contacted my ISP, they said get a new router. Tried re-installing firmware, no change. I haven't tried it on a different internet connection yet, but plan to visit a neighbor and do some begging
I just purchased netgear N150 single band wireless router WNR1000v3. I cant get to the 192.168.9.1 site to detup manually and when i insert the set up CD it scans the config & says that my ethernet adapter isn't intstalled or enabled....I HAVE A CABLE FROM THE SATELLITE MODEM to my computer which works fine when I am connected direcrtly to it, so I dont get what the problem is. Do I need a different cable connecting my computer to the LAN on the router or am I missing something?
I have a desktop connected to our work network. It's running XP Pro. I also have a laptop running vista home. Is there a way to hardwire that laptop to the desktop, so i can share files between those two computers, while ALSO keeping my desktop connected to my office network?Since it's vista home, I can't connect the laptop to our network, since it can only connect in workgroups, not networks. But if I'm just able to just use the laptop, create files, and then either save them to a shared folder with my desktop or just save them to the desktop with a switch or something, it wouldn't be a problem that my laptop can't connect to the network.
The modem Time Warner gave me several years ago was dying, I took it in, they gave me a Cisco modem, I plugged it into the computer, works fine, so then I plugged it into my airlink 101 wireless router, the computer recognizes the router but says there is no internet access, i.e. the modem and router are not communicating. Why would change of modem cause lack of communication with the router, is there something different about modems now compared with roughly 5 years ago? And what can i do to fix it so i can have wireless access again? If it matters, I have no protection on my wireless (because I never figured out how).