Routers / Switches :: Connecting And Installing Netgear WNR1000v3?
Jan 5, 2013
I just purchased netgear N150 single band wireless router WNR1000v3. I cant get to the 192.168.9.1 site to detup manually and when i insert the set up CD it scans the config & says that my ethernet adapter isn't intstalled or enabled....I HAVE A CABLE FROM THE SATELLITE MODEM to my computer which works fine when I am connected direcrtly to it, so I dont get what the problem is. Do I need a different cable connecting my computer to the LAN on the router or am I missing something?
my Netgear WPN824v2 router won't connect to the internet. It stopped connecting after a power outage 4 days ago. All local connections work fine. wireless unaffected. I tried a different router, but it wouldn't work either. Contacted my ISP, they said get a new router. Tried re-installing firmware, no change. I haven't tried it on a different internet connection yet, but plan to visit a neighbor and do some begging
I have a Netgear WNR1000v3 router. I have two computers connected with a wired connection and a couple of different devices that I connect with using the wireless connection. (Phone, Laptop, Ipad). The wired connections work fine but the wireless connection will only connect to the internet for a very short time (seconds) and then drop off. If I wait long enough I will pick it back up again. But again, for only a very short time. I have tried all the reboot procedures without any success. If I reboot the laptop, Ipad, etc., that seems to get me a connection, again for a very short time. I've checked the lights on the router and everything there says its OK. It seems to have to difference how far I am from the router. I've put the computer right next to it without success. Is the router going bad? It's only about 4 months old. Because I don't use the wireless feature often, I can't tell you if it ever worked or not. It seems to me like I was able to keep a connection when I first hooked it up but I'm not sure.
I have a router and its settings can be accessed by going to 192.168.1.1, I also know that there are other users that are able to access this page and change the settings when they connect to the wireless router. What I want is to block the wirless router page on computers that connect to my wifi except for 1 computer which would be mine. I've tried to put the password but to no avail the password is easily guessed or cracked and settings are changed. But is there a way to block the Wireless router setting page on computers that connect to the wifi network?I have a Netgear Wireless Router WNR1000v3 N150.
I just updated the firmware on the WNR1000v3 router. However all the port forwarding configs that were set up previously have become "ghosts". They do not show up on the list nor work, but I cannot add a new entry.
I bought a new router last night in an attempt to fix some internet issues. I replaced my old router (an N150 lynksis) with the one I bought (an N300 netgear) and after getting all the wires connected, my computer wouldn't connect to the internet and it wouldnt recognize the router as anything other than "Unidentified Network". I've tried reseting and power cycling the modem, shuting down the computer, even some random tips from the internet but nothing seems to be working.
I just got digital cable, phone and internet and when I try to use the digital phone and internet at the same time, the internet wouldn't work. Its connected through Netgear N300. The wireless connection will not stay connected.
I have a Netgear WNR3500L with a Comcast cable modem. The internet was running slow so I rebooted everything. After that I could not see the internet. I tried to reset the Netgear Router, shut down and restart and still the same problem. I plugged the computer directly into the cable modem and everthing works just fine. I'm guessing something happened to the Netgear router but I don't know if it is a setting or something happened to the router itself. The router is about a year old. I can use the default 192.168.1.1 to get into the router but I'm not sure what settings I should try to change.
I have set my Netgear WGR614 to a static IP, and I have tried port forwarding but I can't. I've tried disabling SPI Firewall and it still don't work. I have also tried enabling bridge settings on my connection in my modem settings, but that just wouldn't let me back on my internet. How I can port forward?I have a westell 610015.
basically, my iMac detects the extender as routername_EXT which is fine, but says that the password i type is wrong. when i use my original router with my iphone with the same password it works, but when i try to use it with my extender it says that the password is wrong.
My Netgear WNDR3300 wireless router has stopped working. I was trying to put new firmware on it and it just stopped being able to connect to the internet. I can't connect to the internet through it wired or wirelessly. Wirelessly I can connect to it, but I can't do anything like browse the web. I have tried resetting it to factory defaults and restarting it and my modem many times, and my modem can't be the problem because using my other router everything is fine.
I cant work out how to get my Netgear DGN2200v3 to port forward.Portforward.com describes how to port forward for a Netgear DGN2200 but NOT for the DGN2200v3.The difference between the DGN2200 and the DGN2200v3 is that when I log into the router and go to port forwarding/port triggering there is no box to fill in the server IP address. It just says service name, service type, starting port, ending port.
I recently bought a second hand in the package netgear maxrange wpn824 router, and it requires a 2.4 ghz 802.11 b/g wireless adapter and windows 98. I have a gateway laptop, operating system windows vista home premium oemact, model: md2614u and it has a ralink 802.11n wireless LAN card. Can I install and operate the wireless router even if I had diferent wireless LAN card?
i tried to change my nat type to open, on my Netgear WNR2000v1.i connected throught typing my routers ip. (192.168.1.1)i watched a utube video, where someone told me that i had to changed something in the basic section to 2, instead of auto.now i cant connect to my router. ive tried with multiple pc's.
I have a Netgear N300 Wireless Router (WNR2000), and I am trying to connect the internet through it. The internet light stays amber, and though the router recognizes it, I can not connect to the internet. My computer also doesn't seem to recognize the router at all. Installation CD will not work either.
Currently I have 2 different modem running in my working area which is modem A and modem B. Whenever user from Modem A(192.168.0.1) or Modem B(192.168.0.10) would like to print or scan something using the shared printer, I need to manually plug the cable into either Modem A or Modem B depends on the network the user are currently using.How I do previously is only set DHCP on Modem A and disable DHCP for modem B so that Modem B will share DHCP assigned by Modem A. Both modems connect to the same Switch with the printer cable so both network user can use it together.But the problem now is I have to enable DHCP for both modems and causing the previously method can't be use anymore. So is there any other way that I can link both Modem A and Modem B with each assign different DHCP to link with 1
I have a building with 30+ pc's, printers and cameras. I do not have a "server" setup, however I want them to be connected to the T1 line comming into the building for internet as well as file sharing, etc.Currently, I have the T1 line connecting to as Linksys E3000 wireless router. From there I have a cable connected to the wireless router (it has 4 ports also) and then going to a Netgear FS524 (24 Port 10/100 MBPS Fast Ethernet Switch) via port number 24. I then have another CAT5 cable connected to a port on this switch, extending to a D-Link DES-1024D (another 24 Port, 10/100 switch)I then have the 30+ CAT5 cable coming into all three of said devices... No then, I get Internet connection on all units, the problem is that I cannot see all of the devices.
I use a Netgear FS605 Ethernet Switch to connect a wifi modem to my network and thus to the internet. People in that room can jump online via the wifi modem. You can also print to the wireless printer in that room via that wifi modem being local. However, I can no longer print to the wifi printer from anywhere else in my network (I could before I got a new router and wifi modem in there).Would this be a problem with this Switch or with the modem e.g.