Routers / Switches :: Netgear WNR3500L Can't See The Internet
Jun 18, 2011
I have a Netgear WNR3500L with a Comcast cable modem. The internet was running slow so I rebooted everything. After that I could not see the internet. I tried to reset the Netgear Router, shut down and restart and still the same problem. I plugged the computer directly into the cable modem and everthing works just fine. I'm guessing something happened to the Netgear router but I don't know if it is a setting or something happened to the router itself. The router is about a year old. I can use the default 192.168.1.1 to get into the router but I'm not sure what settings I should try to change.
I currently have a NetGear WNR3500L running Tomato acting as an access point. Unfortunately, I think it's crapping out on me... Currently, there are two WiFi security cameras streaming through it to a surveillance server 24/7, and even though it is in a central location in my condo, I get shit signal ~25 feet away (and that's after cranking up the wifi radio to 60mw).
802.11n is a must, and dual SSID's would be nice too... dual band would be totally awesome but not that necessary (I still have some legacy hardware running on G...).
I just found out I was having packet loss with my toshiba satellite. I have a NetGear WNR3500L freshly installed because the old router (d-ling dir 615) was dropping the connection all the time so we changed it, But now I'm still having problems of lag so I'm well ill do some tests, find out I lose packets so i blame it on the router but then i make the same test on a wired computer wich didnt lose any packets at all. I came to the conclusion it had to be my pc, i did the test both while be wired and wireless.
my Netgear WPN824v2 router won't connect to the internet. It stopped connecting after a power outage 4 days ago. All local connections work fine. wireless unaffected. I tried a different router, but it wouldn't work either. Contacted my ISP, they said get a new router. Tried re-installing firmware, no change. I haven't tried it on a different internet connection yet, but plan to visit a neighbor and do some begging
I have a Netgear N300 Wireless Router (WNR2000), and I am trying to connect the internet through it. The internet light stays amber, and though the router recognizes it, I can not connect to the internet. My computer also doesn't seem to recognize the router at all. Installation CD will not work either.
I have a Netgear WNR3500L wireless router. I assume it's v1 because on the back it doesn't have "v" anything. Firmware version V1.2.2.44_35.0.53NA.When I connect using g I get 22+Mbps download speed. When I connect using n I get 10 Mbps. I've tried using both WPA2 only (laptop reports 130 Mbps connection I believe) as well as the combo WPA+WPA2 (laptop reports connection of 117 Mbps).Broadband download results don't change - they stay at the 10 Mbps level. I've fiddled with some of the settings on my laptop's wireless card - but the results are the same.For now I'm just trying to figure out where I should focus my investigation and fiddling efforts - on the laptop or on the router.
I just got digital cable, phone and internet and when I try to use the digital phone and internet at the same time, the internet wouldn't work. Its connected through Netgear N300. The wireless connection will not stay connected.
Cant log in to my router I've tried 192.168.1.1, 192.168.0.1, (url )Don't know what else I can try keeps poping up with search results. Oh, also tried reseting router and cable modem.
I have set my Netgear WGR614 to a static IP, and I have tried port forwarding but I can't. I've tried disabling SPI Firewall and it still don't work. I have also tried enabling bridge settings on my connection in my modem settings, but that just wouldn't let me back on my internet. How I can port forward?I have a westell 610015.
how to configure a server with net gear switch . I want to restrict access for a few users and use the netgear switch for file sharing between the small network. its got auto configuration .
basically, my iMac detects the extender as routername_EXT which is fine, but says that the password i type is wrong. when i use my original router with my iphone with the same password it works, but when i try to use it with my extender it says that the password is wrong.
I just purchased netgear N150 single band wireless router WNR1000v3. I cant get to the 192.168.9.1 site to detup manually and when i insert the set up CD it scans the config & says that my ethernet adapter isn't intstalled or enabled....I HAVE A CABLE FROM THE SATELLITE MODEM to my computer which works fine when I am connected direcrtly to it, so I dont get what the problem is. Do I need a different cable connecting my computer to the LAN on the router or am I missing something?
My Netgear WNDR3300 wireless router has stopped working. I was trying to put new firmware on it and it just stopped being able to connect to the internet. I can't connect to the internet through it wired or wirelessly. Wirelessly I can connect to it, but I can't do anything like browse the web. I have tried resetting it to factory defaults and restarting it and my modem many times, and my modem can't be the problem because using my other router everything is fine.
I cant work out how to get my Netgear DGN2200v3 to port forward.Portforward.com describes how to port forward for a Netgear DGN2200 but NOT for the DGN2200v3.The difference between the DGN2200 and the DGN2200v3 is that when I log into the router and go to port forwarding/port triggering there is no box to fill in the server IP address. It just says service name, service type, starting port, ending port.
i tried to change my nat type to open, on my Netgear WNR2000v1.i connected throught typing my routers ip. (192.168.1.1)i watched a utube video, where someone told me that i had to changed something in the basic section to 2, instead of auto.now i cant connect to my router. ive tried with multiple pc's.
I have a WN3000RP WiFi Range Extender but I cannot seem to find out how to connect to it on my Windows 7 Desktop computer to configure it. My Router is a Netgear Wireless G RouterWGR614 v9
I use a Netgear FS605 Ethernet Switch to connect a wifi modem to my network and thus to the internet. People in that room can jump online via the wifi modem. You can also print to the wireless printer in that room via that wifi modem being local. However, I can no longer print to the wifi printer from anywhere else in my network (I could before I got a new router and wifi modem in there).Would this be a problem with this Switch or with the modem e.g.
I have had the Netgear 3300 Dual Band for three years. Everytime I wanted to access using my laptop, I had to choose between 2.4G and 5G connection. For about a month now, the 5G does not show up. It doesn't show up as a network to select no matter what device I use. I have reset the router and updated the firmware. Both connection lights are blinking. I recently purchased and IPhone 4 and still I do not have the option of selecting 5G.
I have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
Last night the power either blinked or had a surge and I lost the internet on both of my computers. After restarting the Hughesnet modem and Netgear WNR3500L router, I now have internet service back on my laptop computer. However, I can't get it to work on my desktop. I have an HP Desktop running Windows XP (actually both computers are XP) using a Netgear Wireless-G USB 2.0 Adapter. Everything worked fine until today. Since then, it seems that the desktop sees the network, but can't connect to the internet. I've looked at a lot of forums and instructions and it sounds to me that the router will not assign the adapter an IP address. My wireless network connections have aegis protocol and tcp/ip selected, with obtain and ip address and dns server address automatically selected. I've uninstalled the adapter and reinstalled it and even done a system recovery on my computer in hopes to reset it, but nothing has worked. As you can see below I've tried most of the suggestions I've found online to no avail. I've also done the winsock and t something stack commands. I also don't know how to access my router b/c it's not connected to a computer. I could access it with my laptop, but I'm not sure how since it was setup with my desktop which required my entire desk to be physically moved at the time.
Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp. C:Documents and SettingsOwner>ipconfig /all
i want to ask if i can link two routers while they are totally separated of each other over the internet to make a large LAN the two routers are TP link?
How do i connect two internet routers to one IP address range?I currently have one broadband router connected on 172.16.0.3 subnet 255.255.0.0, I have a second line which is a copper ethernet EFM 2Mb line connected using a Cisco 1800 router configured on 172.16.0.254 subnet 255.255.255.0, no DHCP is configured on either router. the dhcp is provided by a windows 2003 server on our LAN which is also configured on the same LAN IP range. if i connect the Cisco router into the same switch as the broadband router my network devices stop working and dont respond.
If i check the broadband router it shows all the connections to it as having the same MAC address as the Cisco router?? if i disconnect the Cisco router everything returns back to normal and works perfectly.What I want to achieve is to be able to run both routers on the same LAN to provide internet access by configuring the pc's to route through a specific router. the DHCP I want to stay routed through my original broadband line. at the same time i want all pc's to access to the lan devices (ie. servers and printers) what the correct configuration would be for the two internet routers would be?
We are replacing some netgear switches with the Cisco SG200. The situation is relatively straightforward. We have a series of VLAN's coming in on a trunk from a service provider for our Metro Ethernet locations. These trunks then get cross-connect to various location for connectivity. The problem we have is there are two VLAN's that need to go to the same switch which provides access to our public IP block.
I set up the two VLAN's on the SG200 with the trunk port VLAN tagging on the service provider port. Then I set up a separate port for untagging the traffic with the PVID of the respective VLANS's as follows: [code] The public switch has no VLAN's configured (it is an SG200 too). If I connect GE2 to the public switch everything works fine. When I connect GE3 to the public switch, things die. I thought this might be caused by STP although STP should not be detecting issues like this across separate VLAN's. Disabled STP, no change.The same configuration with the Netgear worked without an issue. FYI, the VLAN's cannot be changed...they are defined by the service provider in this particular case. otherwise we'd just make them the same..
with a networking issue that I'm having with the 2nd computer I have trying to connect to the interntet via my Westell 7500 DSL router. I ran the diagnostic tool on the NIC to make sure it working correctly and it is, and so is the cable according the tools; I also verified that myself via unplugging/plugging the cable into the router and it detects eachMy other 2 computers work fine via the router.Here is the ipconfig info;Host Name:XXXXXXPrimary Dns Suffix: (blank)Node Type: HybridIP Routing Enabled: NoWINS Proxy Enabled: NoEthernet Adapter Local Area Connection:Connection-specific DNS suffix: (blank)Description: Intel(R) 82562V-2 10/100 Network ConnectionPhysical Address: 00-1D-09-8D-34-3BDHCP Enabled: Yes
Some day, then my internet jut died. then I got the router restarted(unplugged the electricity and plugged it back in) and it worked for like a day and then it died again. I restarted the router again Internet worked and then some hours later it died again.This problem only happens to me and not anyone else in the house.I'm connected from my pc with and ethernet cable to a switch/HUB where it's then connected to the router.
The connection of the computer before is activating.. after how many days of using,it losses the internet connection.. what is the possible reason for this?
I have an ARRIS modem supplied by Comcast cable. I have an hp pavilion x1958 and want to run internet service to a secondary computer from the same modem. And I don't have money to buy a router. How can I do this the cheapest way?
