Netgear WNR1000v3 N150 - Blocking The Router Page?
Sep 3, 2012
I have a router and its settings can be accessed by going to 192.168.1.1, I also know that there are other users that are able to access this page and change the settings when they connect to the wireless router. What I want is to block the wirless router page on computers that connect to my wifi except for 1 computer which would be mine. I've tried to put the password but to no avail the password is easily guessed or cracked and settings are changed. But is there a way to block the Wireless router setting page on computers that connect to the wifi network?I have a Netgear Wireless Router WNR1000v3 N150.
View 7 Replies
ADVERTISEMENT
Feb 8, 2012
I have a Netgear WNR1000v3 router. I have two computers connected with a wired connection and a couple of different devices that I connect with using the wireless connection. (Phone, Laptop, Ipad). The wired connections work fine but the wireless connection will only connect to the internet for a very short time (seconds) and then drop off. If I wait long enough I will pick it back up again. But again, for only a very short time. I have tried all the reboot procedures without any success. If I reboot the laptop, Ipad, etc., that seems to get me a connection, again for a very short time. I've checked the lights on the router and everything there says its OK. It seems to have to difference how far I am from the router. I've put the computer right next to it without success. Is the router going bad? It's only about 4 months old. Because I don't use the wireless feature often, I can't tell you if it ever worked or not. It seems to me like I was able to keep a connection when I first hooked it up but I'm not sure.
View 1 Replies
View Related
May 15, 2013
I just updated the firmware on the WNR1000v3 router. However all the port forwarding configs that were set up previously have become "ghosts". They do not show up on the list nor work, but I cannot add a new entry.
View 2 Replies
View Related
Jan 5, 2013
I just purchased netgear N150 single band wireless router WNR1000v3. I cant get to the 192.168.9.1 site to detup manually and when i insert the set up CD it scans the config & says that my ethernet adapter isn't intstalled or enabled....I HAVE A CABLE FROM THE SATELLITE MODEM to my computer which works fine when I am connected direcrtly to it, so I dont get what the problem is. Do I need a different cable connecting my computer to the LAN on the router or am I missing something?
View 2 Replies
View Related
Jul 12, 2012
I have just bought a Belkin n150 router. Connected it to my modem and PC and I'm recieving internet. Connected my phone and laptop and getting wireless.The issue, however, is that I cannot login to the router page. The login says to leave blank for default, but it gives me an incorrect password error. I have tried resetting using the button located above the power cable to go back to defaults, but I continue to recieve the error.
I have tried a all the other usual default passwords, password, administrator, admin, etc.I've gone through pages of google search results and found nothing. Have I missed something obvious or did Walmart sell me a defective router?
View 1 Replies
View Related
Mar 20, 2011
I have a DVR connected to CCTV cameras that I would like to connect to my computer via Ethernet and a Netgear N150 router which also handles my broadband.
A program called VideoViewer is installed on the computer which works with the DVR to view images on the computer via ethernet.
Funny thing is that it works with a Zoom router, but not the Netgear There must be settings on the Netgear that needs changing
View 9 Replies
View Related
Aug 2, 2011
The laptops in my flat are wirelessly connected to a Netgear N150 Wireless router and the connection is forever going from little to nothing. I've tried resetting everything, getting Orange to replace the router (a new Netgear N150) but still nothing. I've tried changing channels in the past but never seems to last. I can't work out if another wireless router in another flat is chomping into our connection
View 14 Replies
View Related
Oct 10, 2011
I am trying to set my NETGEAR N150 DGN1000 . I can connect to the router via wireless but no Internet.
Theh INTERNET PORT indicator on the router is goes to OFF mode.
Before I try this I had Internet with the same line with a different router.. I am not too sure what's wrong with this.. Could any one come up with a possible solution..
View 5 Replies
View Related
Jul 12, 2011
I have a wireless router Netgear WNR1000 N150. I am wondering if I can use it as an access point/ repeater, and if I can, how to set it up. The modem provided by the ISP is in the room with the desktops; can I place the wireless router in a room
View 2 Replies
View Related
Mar 4, 2013
How to change security on Netgear N150 wireless router ( set it to no security)?
View 1 Replies
View Related
Nov 6, 2012
I've been using my WRT310Nv2 Cisco wireless Gigabit N router for 2 weeks now, and sometimes, it's blocking access to Facebook.comI am not aware if it does the same thing with other websites, but my guess is that if I fix this one, I'll fix them all. So here I go, I click on my Facebook icon in my bookmarks and all goes well. Then, a while after, Facebook doesn't respond anymore and I'm send to a page that says "this is probably not the webpage you are looking for!" and it goes on about someone probably trying to hack my Internet and so on. But it's impossible: my network is under a solid WPA/WPA 2 security access. So I try again and click on the FB icon, and it shows me this:
"Invalid URL
The requested URL "/", is invalid.
Reference #9.c2c28f18.1352263449.304a8c9"
View 9 Replies
View Related
Mar 7, 2012
my netgear n150 router can not send wireless signal to devices.what is wpa or wps. how can i find my wireless user name and password. does paying 80.00 dollars to netgear solve problem.
View 1 Replies
View Related
Sep 16, 2011
I am trying to set my NETGEAR N150 DGN1000 .I can connect to the router via wireless but no Internet.Theh INTERNET PORT indicator on the router is goes to OFF mode.Before I try this I had Internet with the same line with a different router..
View 3 Replies
View Related
Dec 19, 2011
basically we got sent this new router from Orange (our ISP) and we have had problems with it for the last week. The router model is the Netgear N150 DGN1000. Sometimes I connect it will be absolutely fine, but then the next time I log onto my laptop it can't identify the network, it says connected but doesn't have the globe in the bottom right hand corner of my screen. Then we have to reset the router a few times everytime until it recognises it, even though the settings are saved when we connected last time. It is the same with my sisters laptop. We both have Atheros network adapters so that may be a compatability issue with the router, but my brother connects fine on his everytime. A similar problem occurs with modern warfare 3 on my ps3, it won't let me sign in to playstation network half the time and keeps saying NAT type failed, even though NAT is enabled on my router. get this problem sorted and to get a consistent network connection that connects every time that would be great. We changed the security type to WEP on it a few days ago from WPA and that meant we could sign into modern warfare 3 some of the time rather than never, but we are still having issues.
View 8 Replies
View Related
Jul 9, 2012
I've got a windows server 2003 machine which access internet over a Netgear N150 router also I've got an static IP, now internet is working properly even I can ping my machine from a remote machine.Here starts the real problem, I've shared few folders which I can't access from any remote machine not in my LAN.Although I could access my server through remote desktop and everything else is working fine, I've opened port 445 on router even that didn't worked also Windows firewall is OFF.Now when I try to browse my server through \myserverip it shows me a blank window but when I tried to access it like:
\myserveripsharedfolder it gives me error which reads something like
"File and printer sharing seems online but server is not responding on port 445."
View 10 Replies
View Related
Feb 25, 2013
After our ISP had a network outage, our Belkin N150 stopped working properly & now I can't get to the Settings page to fix anything. I have used the Reset feature to no avail. The blue light is on but the "Fixit" feature only comes up with something about the ASDL line.
View 1 Replies
View Related
Aug 6, 2011
my netgear router is blocking my printer
View 1 Replies
View Related
Jan 13, 2012
I bought my dad a Netgear N150 DGN1000 Wireless ADSL Router to replace his D-link router which kept dropping the wireless signal. I have established a wired connection and my ipad, iphone and his old laptop connect wirelessy to it without any problems but I just cannot work out why his laptop won't connect to the internet.It recognises the wireless signal and it says its connected and that the signal is excellent but when I try to go on the web or check emails it just won't work.I've tried deleting all his wireless networks and starting from scratch but don't know what else to tryHis PC is running windows Vista
View 9 Replies
View Related
Apr 13, 2012
I have a Netgear N150 Wireless ADSL2+ Modem Router(DGN1000) which i need to connect for wireless access..My internet connection is a wireless one(antenna connected on roof) connection available to only one computer with an RJ45 LAN.Is it possible for me to connect the router to this LAN cable and get internet on more than one computer at a time?? I have the following information
IP :
Subnet :
Default Gateway :
Primary DNS :
Secondary DNS :
MAC of the Registered Computer :
View 2 Replies
View Related
Feb 10, 2013
Is there a way to quickly disable Wi-Fi on a N-150 from the router setup page? I have looked on my admin page but I don't see it. I just want to be able to turn the radio on and off from the PC that is connected via ethernet.
View 3 Replies
View Related
Dec 31, 2012
I am trying to set p my Netgear wireless router but each time I type in the IP address, it says the page cannot be found. I am using Windows 8
View 2 Replies
View Related
Jun 3, 2011
My brother just updated the firmware on my Netgear N150 router. My computer shows my wireless network and shows full strength, but says unknown error when I try to connect. It does not appear to save the network password (WEP). My bro reverted the firmware, but still no go... Ethernet works fine, but unsure if it is limited to onmy my wifi. The Error Mesage reads: Wireless association failed due to an unknown reason
View 10 Replies
View Related
Feb 11, 2012
I purchased a New Netgear N150 wireless Router 2 weeks ago and now my internet on my laptop keeps going down.. As Far as I can tell When it drops its still connected to the Wireless network.. it just says local only and Gives me the limited connectivity warning.. When I diagnose the issue it tells me a number of different things and it tells me to renew the IP settings and sometimes that will work and sometimes not.. The laptop is a HP Pavilion DV9000 with all original hardware.
View 1 Replies
View Related
Oct 19, 2011
I have a Netgear N150 Adsl router with Orange and the internet light is constantly red and i have no internet connection i can connect to the router but have no ip address.
View 1 Replies
View Related
Jan 12, 2012
I have a Dell Studio 1745 Laptop and its only a few years old, I recently upgraded my router to be wireless a year or so ago and have had a few d/c issues here and there but mostly has not been a problem.Recently I have had tons of d/c issues while playing warcraft or browsing the internet in general, anything really.So I made the mistake of recently updating my WNR1000V3 router's firmware from my laptop's wireless connection. After I did this I saw all sorts of warnings (none built into the firmware itself, sigh) that this was a big no no.
Since then my d/c issues have been horrible but what it does now is my connection will be completely normal then all of a sudden my wireless access point will switch to 'No Internet Access' and it will drop my internet.The only way I can get it back is to go into the other room and reset the router by either unplugging it, or pressing the reset button on the back, once it reboots and everything, my laptop sees the connection again, and it has Internet Access fine.Soo I went and made the problem much worse, the lame part of the situation is before I had this firmware issue I was getting this problem anyways.
I decided if I could flash a older version of firmware to the router using my desktop that is wired to the router I could then reupdate it to the current version,I found a old firmware version on netgear.com and went to upload it through the router login for my router, it then said the file format was unrecognizable or not the right one (it was a .img file). I even tried to mount the file and explore it, no go. I found another firmware version older than that and attempted to flash that to the router and it began to update, then gave me a warning that this firmware was older than my current, I click yes and my internet drops and the update never happens.
So if I did screw the modem up this way I have no idea how to fix it now I have reset it to factory settings but this doesn't affect the firmware version. I suspect the firmware has something to do with the recent problems because I have seen the 'Congratulations, You have setup your router and are connected to the internet" like 20 times these past 48 hrs.I downloaded Xirrus wifi inspector and have it running now.I tried the ip flush and release stuff, and a bunch of tricks ive seen on other forums.My system is Windows 7 with a Intel wi-fi link 5100 AGN network adapter. I have tried rolling back that network driver and messing with the advanced and tcp/ip settings.
View 14 Replies
View Related
Mar 22, 2012
I have just picked up an ADSL Netgear N150 DGN1000 router as my old router (just some branded old thing from my ISP has started playing up a bit due to age more than anything else) but for some reason it is not seeing my internet connection at all.I've reset it factory default twice and connect to it wirelessly just fine, including accessing the router's setup pages and whatnot. I was going to update the firmware from in there.. but that needs the connection to the internet as well.
My ISP is BE Unlimited (UK ISP) and their old branded modem connects again immediately when I plug that back in so I know it's nothing to do with any of the cables or filters, etc.One thing I have noticed is that on the box for the new router it does say Orange Retail (another UK ISP) on one of the barcodes but the router itself isn't branded, so I don't see this could be a problem but figured it was woth mentioning.
View 1 Replies
View Related
Nov 12, 2011
My wife has a COBY 10" netbook running Windows X home SP3., we use a NETGEAR N150 Wireless Router and for some time now, whether she boots from a cold startup or "wakes" this laptop, it has lost the network connection. It gets the "Wireless networks detected" message, sees our Security-enabled wireless network, but instead of automatically connecting, it always asks for the network key. I have a second laptop (Toshiba Qosmio) that I only use some othe time, primarily for vacations, and when I turn this on it always connects right to the network, even if we've been away and connected to a hotel network. I never have to use the key for our home network once I get back home.
She's getting pretty fed up having to constantly put in the network key on the COBY, this should be a "set it once" and it should remember it should it not? I'm sure it used to, have I missed something?
View 4 Replies
View Related
May 14, 2011
Im having a horrible problem with my internet connection where I cannot use any kind of download site such as filefront or anything really.The main problem is once a download gets going (any filesize above 1MB) the connection will stall out and stop downloading until the server says cannot download or if available, i pause and start the download again. Its very frustrating having to babysit downloads or be unable to even complete one ,My router is a netgear N150 WNR 1000.
View 14 Replies
View Related
Aug 29, 2012
My son is using the above access point on his laptop. He wants to make the connection secure by having a password that you must enter in order to access it. How does he set up this password? Looked at the user manual; see the screens but don't know how to get to the screen.
View 2 Replies
View Related
Apr 28, 2011
Dell 8600 centrino intel pro wireless lan 2100 won't connect to netgear n150 wnr1000. Running 802.11b band it sees wireless network but won't connect. I have 2 other computers connected to network so it works.... I don't know if Netgear n150 is compatible with 802.11b band...
View 1 Replies
View Related
Feb 25, 2012
For some reason I cannot ping or FTP on a specific computer on my home network. All other computers work fine and the specific computer works fine on other networks. But the combination of this computer and my home network it doesn't like.
I have disabled both windows firewall and my virus software but nothing seems to work. It seems to be a timeout issue as FTP and ping sometimes does work but FTP is increadibly slow when it works and the ping time is very high 670ms and above. I am running windows 7 and my router is a netgear n150
View 4 Replies
View Related
Mar 11, 2011
how to block a dynamic wireless IP address or the SSID of a wireless connection from accessing my router?
I have 2 people that have somehow managed to get access and i wish to discard them so they cannot reconnect. My wireless router is a Netgear WPN824 and i am running Windows XP.
View 3 Replies
View Related
Feb 26, 2013
I recently bought a Netgear Pro-safe VPN firewall. I have 3 or 4 Xbox consoles on my network. After a few days i got multiple complaints that the users kept getting disconnected from Xbox live after i installed this firewall. I have noticed that it only does it to the xbox, computers and laptops are working great. I also noticed that, 5 or 10 sec. before the router goes out. The firewalls indicator lights all light-up at the same time. Then it resets and the connection restores itself. It happens mostly when using Netflix through the xbox. I have tried port forwarding but it seemed like it made it worst.
View 3 Replies
View Related
