Routers / Switches :: Configure SpeedTouch Router As Access Point?
Nov 5, 2011
i have a LAN network between several pc's connected with several switch's and connected to Thomson SpeedTouch 510 DSL Router its ip address is 10.0.0.100 subnet 255.0.0.0 and the router dont give auto ip to the PCs i have to issign it manually to the PCs "static ip".I bought the acer android recently so i bought a tp-link td-w8901g wireless router to act as an access point so i connected the 2 routers to each other by LAN and gave the tp-link an ip address 10.0.0.12 subnet mask 255.0.0.0 so it will be the same ip range of the speedtouch and setuped the tp-link router to fit my isp configeration it worked at first but i had to reset the router so i did the same configuration i did before but didnt work and i cant access the internet using the android or the wireless but when i connect the phone to the tp-link and unplug the speedtouch the wireless works so theres no any problem with the router?
View 1 Replies
ADVERTISEMENT
Mar 13, 2011
I have high-speed cable access currently coming into an older D-Link 4-port wired router. I need to buy a new wired and wireless router so I can sync my new Android 4G phone (I'm in an area with bad cell coverage but I can sync with wi-fi). I have a second house about 200 feet from mine and have 3 Cat5E lines running underground in conduit to it so the lady next door and and her two kids can use the internet (I have 40-50mb service for my business use at home). Problem is that my kids have discovered YouTube, streaming video, video chat, etc. and are burning up my bandwidth. I currently have two of the lines to them disconnected so that I can limit their use to one computer at a time. I'm considering having them buy a Wireless Access Point, can they connect it to the standard single Cat5E LAN wire that is coming from my new wired and wireless router when I buy it?
View 2 Replies
View Related
Jan 11, 2013
I just switched over from AT&T Uverse to time Warner cable for Internet. I bought a Motorola Surfboard sbg6580. I have the surfboard hooked up and all is well. Now I would like to do in put the old 2wire from AT&T in a room upstairs and use it as place I can plug in the Ethernet cords and also transmit another signal. I have what's a called plug link that is plugged in down stairs and then another upstairs and it allows the Internet signal to run through the power lines. So it just about the equivalent of running a cord for down stairs to upstairs. So basically I just need to plug more then 1 thing upstairs that isn't wireless and I would also like to transmit a 2.4ghz signal upstairs and use my Motorola to transmit a 5ghz.How would I set up the 2wire to do this.
View 3 Replies
View Related
Nov 9, 2012
As per settings menu, I tried to give it an IP address but the new address is not accessible for further configuration. When I connected to the router it status changes to "unidentified network".
My primary network address range is 192.168.1.1 to 192.168.1.10. So I gave address to belkin as 192.168.1.100. But I can not access this address from both primary and belkin network.
View 2 Replies
View Related
Jul 6, 2012
Here is my set up:
192.168.1.1 is a Linksys WRT610N acting as a router and DHCP server for addresses .100 to .150
192.168.1.2 is TEW-639 with DHCP turned off and connected to the Lynksys via one of the LAN ports.
I then have a FosCam camera with IP 192.168.1.010, connected either wirelessly or via a wire on a LAN port to the TEW-639W.
Here is my problem: If the FosCam is connected wirelessly to the TEW-639W I am unable to see it from any device connected to the Linksys. If I connect the FosCam via a wire to a LAN port on the TEW-639W then I can see it from a device connected to the Linksys device.If a device is connected to the network via the TEW-639, I can see the FosCam whether it is hardwired or wirelessly connected to the TEW-639. What am I doing wrong?Why can I not see the wireless connections on the TEW-639 from a Linksys connected device?,The setup is that the internet comes in and is connected to the Linksys, which then via LAN cable and LAN ports on both devices is connected to the TEW-639, which is then connected to the camera.
View 2 Replies
View Related
Feb 4, 2011
i have dlink dwl g700ap wireless access point.. router will show default and no password. i try to connect by ip 192.168.0.050 as per manual guide by cannot.my default gateway is 192.168.1.100 taking lan wire from builing internet that used cisco.
View 1 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Apr 17, 2011
am trying to find the configuration code and steps to configure a router to a wireless access point.
View 2 Replies
View Related
May 1, 2012
Is it possible to configure WRT120n as an access point?
View 1 Replies
View Related
Jan 18, 2011
How do I configure my Linksys N Router for a Netgear Wireless N Access Point set in repeater mode? Linksys and Netgear are communicating, but no Internet access is available on Netgear which makes me think I need to configure Linksys to provide Internet connectivity to the Netgear access point repeater.
View 1 Replies
View Related
Jan 14, 2012
I have a linksys wireless-N router model number is WRT120N and I need to use it as an access point. How i can do that?
View 1 Replies
View Related
Nov 20, 2011
How can I configure my TP-Link router TD-W8950ND act as an access point? I'll be connecting it to a main router which is connected to the ISP.
View 1 Replies
View Related
Aug 13, 2009
I would like to configure it as an access point on my LAN, similar to the way my WAP55AG works.My research on the Internet and on these forums indicate that I have to disable DHCP on the router as well as use the LAN ports to connect it to my network.I am able to turn off DHCP, but assigning it a static IP address is challenging.I can set the IP address, but I am unable to set the subnet mask to 255.255.254.0 as I am only getting a set of SM in a drop down list whick are all 255.255.255.x
View 9 Replies
View Related
Nov 8, 2011
how to access an E1550 wireless router's settings and configure it to connect to my wireless DSL router? The DSL phone line is not located anywhere near my TV/DVR/Roku and I'd like to connect them wirelessly to our DSL router. The E1550 is next to the TV/DVR/Roku.
View 6 Replies
View Related
Mar 30, 2011
i have a pppoe connection coming through ethernet line. i.e i need to use dialer that i have created on the desktop..and i have bought a new Linksys E1000 router v2.1..now my problem is that1) After entering all the settings correctly my router worked for 3 days after that the net is not working.i.e it cannot connect to the internet keeps giving the error cannot get IP from PPPOE(i have connected my router in pppoe mode and use the router status page to connect and disconnect)I have also updated the router to the latest firmware 2.1.01 and after that the problems have started.My Net works if i directly plug the Ethernet cable in the PC.the problem starts when i connect it to my router.
View 3 Replies
View Related
Jun 22, 2010
I'm very dissatisfied with the range and signal strength of my new WRT610N dual band router compared to the WAP54G Access Point I used before.Can I configure the Access Point as a repeater for the 2.4 GHz band on the WRT610N if I use the WRT610N as a Wireless G router rather than wireless N?Â
View 5 Replies
View Related
Dec 8, 2011
I have installed a DIR615 N Router and can get onto the Internet on the PC, but when I type in the device IP address it comes up with an "error" message so I cannot configure it.
View 6 Replies
View Related
Mar 29, 2011
I remember long ago I was upto some trial and error with my router and I ended up in changing some ip that I didn't know about that time, now when I was trying to forward some of the ports. I addressed the computer to 192.168.1.1 (as this was my ip that time I remember and on the box its written too) but it didn't respond, then I remember that I have changed this ip to something else and now I can't remember this.
View 7 Replies
View Related
Jun 17, 2012
i am adding a wired router,during configuration i must choose between PPPoE,Dynamic,Static connection type. i have broadband cable isp
View 2 Replies
View Related
May 30, 2011
i have a ZyXel prestige 650H-31 Model # router and i'm not able to go on to configuration page of the router i tried 192.168.1.1 several times, even after system reboot and router reset, but of no use. I've a wire connection with desktop (RJ-45 port) not USB AND MY PPPoE lights never lit. originally when i entered the gateway 192.168.1.1 it asked me for username & password, since i didn't have the password at that time i tried to reset the router but after that when ever i entered 192.168.1.1 in the browser it never came up with the option to enter user name & password. I've checked all the wires are also connected. I tried prompt command and it showed that timed out thrice and then sent= 4 received= 0 lost= 100%. I had D-Link router prior to it and later connected the D-Link router an i was able to get connected to net and browse normally.
View 1 Replies
View Related
Mar 17, 2012
I have a Hawking 300N and I have misplaced my disk and I neing walked through this to have it set back up. I hooked it all up correctly and it says no internet connection
View 1 Replies
View Related
Aug 12, 2011
I've noticed recently that my laptop keeps disconnecting from the internet via my router (Thompson Speedtouch ST585v6sl.)The light on the router that shows the connection turns red or sometimes it doesnt light up. However all the other lights stay on, it's just the internet light.It only happens for around 5-10 minutes and then after troubleshooting, disconnecting and reconnecting it's back up.I've scanned my computer for viruses and malware and nothing has come up, this is happening reguarly now about every 30-45 minutes when i'm on my pc.
View 3 Replies
View Related
May 2, 2011
i am unable to configure my netgear router with my clear modem
View 1 Replies
View Related
Jul 9, 2012
i recently had att u vesre installed at my house with a 2 wire 3801 router/ modem but i cant get my xbox 360 online. how to configure the router for the xbox 360 so i can play xbox live.
View 1 Replies
View Related
Jun 13, 2011
I want to know how to configure wireless access point because i got new internet connection in my home i want to share connection with my nighbour so we bring TP-Link wireless access point bought one cable wire connect with switch and another one connect with TP-LINK access point, but it is not working .now we dont know how it will be work.
View 2 Replies
View Related
May 16, 2013
I have a N600DB configured as a primary router. I got another playmax n600HD router which I want to configure as an access point that extends my network upstairs and allows me to attach some wired devices like my ps3. I followed the basic principles of setting as access point and my locally connected ps3 and NAS are communicating but no Internet access. How the 2nd router can connect to the internet?
View 2 Replies
View Related
Mar 25, 2011
i have just connected my linksys e2000 to the internet now i would like to set it up so other computers can connect to the internet through it wired/ wireless
View 1 Replies
View Related
Nov 28, 2012
I don´t really have the RJ45 cable, how to configure it as an access point wirelessly? I mean,just by entering the main menu with the default ip address.
View 1 Replies
View Related
May 21, 2011
I am trying to configure Cisco 887-W ISR but have hit a stumbling block when trying to configure the wireless access point- or at least the advanced features of the access point using the URL referenced in from the cisco GUI configuration utility (Cisco Configuration Professional ). I do recall previously reading a post which referenced a different URL.
View 2 Replies
View Related
Jun 22, 2012
I'm having some difficulties with the VLAN setup on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is only able to access the internet when it is plugged into a port that is on the default VLAN (PVID 1). If I plug it into one of the other VLANs then any clients connected to the WiFi lose access to the internet and cannot access devices on the VLAN. I have previously used this setup with a first generation Cisco WAP4410N. [code]
View 4 Replies
View Related
Aug 23, 2011
My apartment already has internet provided to all of the rooms, but I'm trying to set up my router as a wireless access point. I tried disabling DHCP on the router, but then I wasn't able to get any internet access at all. Does this device not support bridge mode?
View 5 Replies
View Related
Sep 17, 2008
I'm trying to access the WAP200 for the first time. Instructions say Configure your PC to have the static IP address on the same subnet as the Access Point's default address (http://192.168.1.245). So I assumed i would go to TCP/IP properties and type in IP address and subnet mask and the Utility would open.
View 3 Replies
View Related
Jan 8, 2007
I have a wrt54gx2 with srx 200 technology recently purchased. I havetwo cabled computers attached. One at one end of the house attached tothe router by ehternet cable, the other attached about 100 ft by ethernet cable.The wireless does not reach to the other end of the house, most likley because that part of the house is an addition with masonary walls and a large masonary firplace. I bought a wap54g access point at the recommendation from someone at linksys to attach to the end of the ethernet run. Since my set up is macintosh, I can't use the wizard disk that came with the wap54g. Linksys support was not support( not expected), I need to know what to do to get this up and running. I am new to this stuff and Linksys get the wireless router with ethernet installed and up and running with my dsl. I thought the same for the wap54g.
View 2 Replies
View Related
