Routers / Switches :: How To Configure Router
Mar 30, 2011
i have a pppoe connection coming through ethernet line. i.e i need to use dialer that i have created on the desktop..and i have bought a new Linksys E1000 router v2.1..now my problem is that1) After entering all the settings correctly my router worked for 3 days after that the net is not working.i.e it cannot connect to the internet keeps giving the error cannot get IP from PPPOE(i have connected my router in pppoe mode and use the router status page to connect and disconnect)I have also updated the router to the latest firmware 2.1.01 and after that the problems have started.My Net works if i directly plug the Ethernet cable in the PC.the problem starts when i connect it to my router.
View 3 Replies
ADVERTISEMENT
Dec 8, 2011
I have installed a DIR615 N Router and can get onto the Internet on the PC, but when I type in the device IP address it comes up with an "error" message so I cannot configure it.
View 6 Replies
View Related
Mar 29, 2011
I remember long ago I was upto some trial and error with my router and I ended up in changing some ip that I didn't know about that time, now when I was trying to forward some of the ports. I addressed the computer to 192.168.1.1 (as this was my ip that time I remember and on the box its written too) but it didn't respond, then I remember that I have changed this ip to something else and now I can't remember this.
View 7 Replies
View Related
Jun 17, 2012
i am adding a wired router,during configuration i must choose between PPPoE,Dynamic,Static connection type. i have broadband cable isp
View 2 Replies
View Related
May 30, 2011
i have a ZyXel prestige 650H-31 Model # router and i'm not able to go on to configuration page of the router i tried 192.168.1.1 several times, even after system reboot and router reset, but of no use. I've a wire connection with desktop (RJ-45 port) not USB AND MY PPPoE lights never lit. originally when i entered the gateway 192.168.1.1 it asked me for username & password, since i didn't have the password at that time i tried to reset the router but after that when ever i entered 192.168.1.1 in the browser it never came up with the option to enter user name & password. I've checked all the wires are also connected. I tried prompt command and it showed that timed out thrice and then sent= 4 received= 0 lost= 100%. I had D-Link router prior to it and later connected the D-Link router an i was able to get connected to net and browse normally.
View 1 Replies
View Related
Nov 5, 2011
i have a LAN network between several pc's connected with several switch's and connected to Thomson SpeedTouch 510 DSL Router its ip address is 10.0.0.100 subnet 255.0.0.0 and the router dont give auto ip to the PCs i have to issign it manually to the PCs "static ip".I bought the acer android recently so i bought a tp-link td-w8901g wireless router to act as an access point so i connected the 2 routers to each other by LAN and gave the tp-link an ip address 10.0.0.12 subnet mask 255.0.0.0 so it will be the same ip range of the speedtouch and setuped the tp-link router to fit my isp configeration it worked at first but i had to reset the router so i did the same configuration i did before but didnt work and i cant access the internet using the android or the wireless but when i connect the phone to the tp-link and unplug the speedtouch the wireless works so theres no any problem with the router?
View 1 Replies
View Related
Mar 17, 2012
I have a Hawking 300N and I have misplaced my disk and I neing walked through this to have it set back up. I hooked it all up correctly and it says no internet connection
View 1 Replies
View Related
May 2, 2011
i am unable to configure my netgear router with my clear modem
View 1 Replies
View Related
Jul 9, 2012
i recently had att u vesre installed at my house with a 2 wire 3801 router/ modem but i cant get my xbox 360 online. how to configure the router for the xbox 360 so i can play xbox live.
View 1 Replies
View Related
Jul 26, 2012
I have one cisco 2851 router and one watchguare firewal currently being used as the main router. I want to connect the cisco as a secondary router on the same network.
View 10 Replies
View Related
Feb 11, 2011
I am planning to put an internet cafe in my place, i want to buy 20 units of PC to start the business. how to set-up or configure the PCs, How to use router and how to configure the PCs to activate the network.
View 4 Replies
View Related
Apr 2, 2012
I have a BSNL wifi modem WA3002g4 . i am unable to configure the modem192.168.1.1 site does not respond
View 1 Replies
View Related
Jul 5, 2011
how to cofiger a network printer in a network, i am using a bsnl broadband connection with user id and psw. all systems are getting internet but printers are not connecting to print.
View 1 Replies
View Related
Apr 1, 2012
i have one machine have 2 Ethernet devices and i need to connect this server to different 2 network with 2 different gateways (192.168.2.x "vpn network" and 192.168.1.x "adsl network" )so if any other one need to connect this ftp server can connected from vpn or adsl
View 1 Replies
View Related
Jan 28, 2011
This is the situation in our Lab.We have one telephone line with broadband connection and a system which is connected to a modem to use this broadband facility. Recently we have taken two static IPs over this connection for a project work.Now what I want to know is, how to configure these static IPs, so that I can connect two systems (each one to one static IP) to use these static IPs and continue to access the internet in the 3rd (already present) system.
View 7 Replies
View Related
Oct 22, 2011
how do i configure cisco switch Edge
View 1 Replies
View Related
Mar 22, 2011
how to configure VLAN on ALLIED TELESYN AT 8024M?
View 1 Replies
View Related
Apr 9, 2012
I have a WN3000RP WiFi Range Extender but I cannot seem to find out how to connect to it on my Windows 7 Desktop computer to configure it. My Router is a Netgear Wireless G RouterWGR614 v9
View 7 Replies
View Related
Jan 29, 2011
I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
View 3 Replies
View Related
Apr 23, 2011
how to connect two subnets with two switches and one router using router sim software?
View 1 Replies
View Related
Dec 15, 2011
Is there a CLI, other than the terminal mode menu, for this switch? I would much prefer to use a CLI to configure it than the (web) menus available.
The web menus are confusing and the manual is long. I already know how to configure Cisco Switches via the CLI quite well.
View 3 Replies
View Related
Feb 16, 2013
I have struck in my some network configuration. I have two sf300 switches and cisco 827 router. Actually sf300 does not support dhcp server. I took cisco 827 as dhcp server and i create 4 dhcp pools in it. How i can configure in sf300 to take dhcp service from cisco router 827. Isit possible to configure 827 with bvi interface, when i was try i got below error. how to configure bvi interface and i will link that bvi to vlan on sf300. error in 827 router, How i can connect two sf300 switch for redundancy ? I connected giga4 SW1 and giga4 SW2 and mode trunk isit good or any other way i need to connect it.?
View 3 Replies
View Related
Mar 22, 2012
why i can not found ip router setting by main menu? the sg300-28 can not support ip router command?mor informations,see my img. If sg300-28 can not support ip router command,what i can do it that communicate by multi-Vlan ?
View 2 Replies
View Related
Apr 22, 2012
I have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
View 2 Replies
View Related
Jun 4, 2012
Is there a way to configure the router through CLI (command line interface)In other Cisco devices we always were able to simply insert a configuration throught the CLI.Now it seems it can only be done with the Webbrowser.
View 7 Replies
View Related
Sep 11, 2011
I have a small business network with multiple systems on a local lan. I would like to expose two of these machine on the Internet using static IPs provided by my ISP. Both of these machines provide web services over ports 80 and 443, and thus port forwarding will not meet my needs. The way I have addressed this issue in the past is to use a router with "multi-NAT" or "many-to-many NAT" support. Alas, the router I was using is no longer working and the company no longer provides a similar offering. In speaking with CISCO customer service today, they suggested that one of the routers in the CISCO 800 series should meet my need.
So my questions are:
1. Is any out there using an 800 series router to address a similar scenario?
2. If so, is it possible to configure this scenario (e.g. Multi-nat) using the Cisco Router Web Setup (CRWS) Tool? I'm not familiar with IOS and would prefer to skip the learning curve.
View 1 Replies
View Related
Feb 20, 2013
How can I configure Belkin N1 Vision Modem router to use Back to My Mac? Bcos in iCloud preferences its give me a error message "setup router for better performance"
View 2 Replies
View Related
Jan 9, 2012
I live in a house of about 30 tenants. The place uses a cisco WRVS4400N router. It seems that my computer gets assigned a temporary ip automatically and then there will be times when I get "kicked out" and my computer doesn't get connected to the internet. Sometimes for few minutes and sometimes for hours.
No idea what happens there but could be that there are no ips left to assign to my computer and someone else gets the ip address.Anyway I'm trying to find out if I can configure my computer with a static ip.
The maximum number of dhcp users was changed from 50 to 100 by me. IDK if that means that I can assign a static ip from 1 to 100 but say I pick a number 160 so the ip would be xxx.xxx.x.160.
1. What are the steps I have to undertake to configure my computer on the router page? What info. do I have to modify?
2. After I modify settings on the router page, do I have to change settings on my computer?
View 1 Replies
View Related
Jan 15, 2013
We have 2 offices in different countries both using the RV082 router. Currently both offices have an internet connection on WAN1 and that is working fine. We are adding a Point to Point circuit between the two offices, and my question is on the RV082 configuration on each side.
I was going to configure WAN2 in DMZ mode on each router, then connect the point to point circuit to the WAN2 port. On the China side, the DMZ IP will have to be a private address (192.168.177.1), while the DMZ port on the San Diego side will be a public IP. We need internal computers to be able to go to the internet normally through WAN1, but also go through WAN2 if they are trying to reach the other network. I will be adding routes on each RV082 for this.
Is there anything wrong with this configuration? Do I need to change the routers from Gateway to Router mode? Does it matter if the DMZ WAN2 port has a private IP address?
View 2 Replies
View Related
Apr 22, 2013
Cisco RV042 Dual WAN VPN Router -how to configure dynamic DNS without having to use the pre-programmed DDNS companies that are populated by default if my DDNS company is not listed and you cannot manually enter another company that is not on the list?
View 1 Replies
View Related
Jun 20, 2012
Is it possible to configure router RV220W to somehow log and track wisited websites?
View 1 Replies
View Related
Apr 29, 2011
i have a router connected to my ISP which can get me 2 different IP's at all times (the router gets one IP).Now i want to get my computer to have a different ip as my router has (seen from outside my home network) - i want my computer that accesses the internet through my router to have a different IP as my router. I know that if my computer gets it's IP from my router's subnet, then it will (seen from outside) always have the same IP as my router. So the question is how do i get around this ? Do i just have to change my PC's DNS / gateway settings to match my router's ? The PC is connected to my router via wifi. Or would forwarding some ports on my router work ?
View 3 Replies
View Related
Oct 9, 2012
I am trying to configure RV082 router with Mac Native VPN Client for my remote access. However, no matter what I did, I am not able to make it works. Can any one can give me an example of how to conguration my RV082 router and Mac Book Pro(Mountain Lion)?
View 2 Replies
View Related
