Cisco Routers :: 800 - Possible To Configure Multi-NAT Using Router Web Setup
Sep 11, 2011
I have a small business network with multiple systems on a local lan. I would like to expose two of these machine on the Internet using static IPs provided by my ISP. Both of these machines provide web services over ports 80 and 443, and thus port forwarding will not meet my needs. The way I have addressed this issue in the past is to use a router with "multi-NAT" or "many-to-many NAT" support. Alas, the router I was using is no longer working and the company no longer provides a similar offering. In speaking with CISCO customer service today, they suggested that one of the routers in the CISCO 800 series should meet my need.
So my questions are:
1. Is any out there using an 800 series router to address a similar scenario?
2. If so, is it possible to configure this scenario (e.g. Multi-nat) using the Cisco Router Web Setup (CRWS) Tool? I'm not familiar with IOS and would prefer to skip the learning curve.
I am using an SRP541W router and i am trying to configure 2 vlans, each one to use its own Wan:Here are the dhcprules and vlans:As can be seen, each one has its own wan interface.
Vlans:As can be seen, each vlan is using its own ports and dhcp rule, so, now they should be separate.
Both Wans are connected: So now (at least as i see things) the two vlans are separate and using different Wan. But the reality is different, everything is going out using Wan1.Also in the Interface Info you can see that the 2 vlans are listed under the Wan1.
why i can not found ip router setting by main menu? the sg300-28 can not support ip router command?mor informations,see my img. If sg300-28 can not support ip router command,what i can do it that communicate by multi-Vlan ?
I have a Hawking 300N and I have misplaced my disk and I neing walked through this to have it set back up. I hooked it all up correctly and it says no internet connection
Possible to configure multichassis port-channel between a VSS and 3750X (Port-channel not in the same switch on the 3750X stack). I got it using LACP but I need Pagp to get VSL redundancy “dual-active detection pagp trust channel-group 1”. I am using the last VSS IOS version 15.0(1)SY. I can’t get the option “switch 1 preempt”, has it changed with other option?
we are moving to different providers. We currently have multiple sites that have MLP bundles going to our current provider. We are trying to limit our network disruptions by creating a new MLP bundle group and connect it to the new provider, but are having no luck. In a GNS3 lab I have setup I am able to keep my existing MLP bundle up/up over the current provider network. When I attempt to bring up a new MLP group to the other provider my MLP does not come up and keeps going up/up then down/down and shows inactive. Is it possible to have one MLP group go to current vendor router, then create another MLP group and go to the other router?
I just bought a Linksys E2000 router and ever since I set it up the internet will cut in and out on my desktop and my laptop, but when I unplug the internet from the router and plug it directly into my desktop (that's how I have it right now) it works perfectly. I have already tried to reconfigure the router and that didn't work either.
Is there a way to set up Quick VPN on the RV120W without changing the internal subnet? I have just taken over responsibility for a network and I don't know all of the nooks and crannies yet, so I'd rather not change the internal sub net. I've tried setting up a user then changing the LAN settings afterward, but it automatically removed the VPN user when I did so.
I've just purchased a couple of SRP527W routers. I've been unable to even browse to the default 192.168.15.1 to start my configuration. My local network is 192.168.1.x. At risk of showing my stupidity, what am I doing wrong.
Is there a way to configure the router through CLI (command line interface)In other Cisco devices we always were able to simply insert a configuration throught the CLI.Now it seems it can only be done with the Webbrowser.
i have a pppoe connection coming through ethernet line. i.e i need to use dialer that i have created on the desktop..and i have bought a new Linksys E1000 router v2.1..now my problem is that1) After entering all the settings correctly my router worked for 3 days after that the net is not working.i.e it cannot connect to the internet keeps giving the error cannot get IP from PPPOE(i have connected my router in pppoe mode and use the router status page to connect and disconnect)I have also updated the router to the latest firmware 2.1.01 and after that the problems have started.My Net works if i directly plug the Ethernet cable in the PC.the problem starts when i connect it to my router.
I am attempting to setup a network containing two routers, a primary giving me ADSL internet access (a 3com 3CRWDR101A-75) and a secondary router that has VPN (Cisco WRV210).
The primary router has the following LAN settings: 192.168.0.1 / 255.255.255.0 with DHCP enabled. WRV210 has the following LAN settings: 192.168.1.1 / 255.255.255.0 with DHCP enabled. Cable connection is from LAN port of first router to Internet port on second router. In this way, I'm able to get internet browsing on 2 laptops connected to WRV210 I have also a Panasonic IP PBX connected on the second LAN (the WRV210)
I need to setup the VPN on WRV210 to be able to get SIP calls from outside of the local networks (through internet). As I am a novice in networking, both routers are on DEFAULT setting.
I have learned a lot during the last 7 days to be able to understand the networking concepts but failed to setup the correct configuration.
For example if I change WRV210 from gateway mode to Router mode, I will not able to browse the internet despite the Help file that says "Select the mode in which this Router will function. If this Router is hosting your networks connection to the Internet, select Gateway. If another Router exists on your network, select Router. When Router is chosen, Dynamic Routing will be enabled"
Also i am able to ping the first LAN 192.168.0.x from WRV210 but not on the other side (from primary router to WRV210).
I am confused to use and combine different settings (NAT, Routing, Ports, ...)
I live in a house of about 30 tenants. The place uses a cisco WRVS4400N router. It seems that my computer gets assigned a temporary ip automatically and then there will be times when I get "kicked out" and my computer doesn't get connected to the internet. Sometimes for few minutes and sometimes for hours.
No idea what happens there but could be that there are no ips left to assign to my computer and someone else gets the ip address.Anyway I'm trying to find out if I can configure my computer with a static ip.
The maximum number of dhcp users was changed from 50 to 100 by me. IDK if that means that I can assign a static ip from 1 to 100 but say I pick a number 160 so the ip would be xxx.xxx.x.160.
1. What are the steps I have to undertake to configure my computer on the router page? What info. do I have to modify?
2. After I modify settings on the router page, do I have to change settings on my computer?
We have 2 offices in different countries both using the RV082 router. Currently both offices have an internet connection on WAN1 and that is working fine. We are adding a Point to Point circuit between the two offices, and my question is on the RV082 configuration on each side.
I was going to configure WAN2 in DMZ mode on each router, then connect the point to point circuit to the WAN2 port. On the China side, the DMZ IP will have to be a private address (192.168.177.1), while the DMZ port on the San Diego side will be a public IP. We need internal computers to be able to go to the internet normally through WAN1, but also go through WAN2 if they are trying to reach the other network. I will be adding routes on each RV082 for this.
Is there anything wrong with this configuration? Do I need to change the routers from Gateway to Router mode? Does it matter if the DMZ WAN2 port has a private IP address?
Cisco RV042 Dual WAN VPN Router -how to configure dynamic DNS without having to use the pre-programmed DDNS companies that are populated by default if my DDNS company is not listed and you cannot manually enter another company that is not on the list?
I have installed a DIR615 N Router and can get onto the Internet on the PC, but when I type in the device IP address it comes up with an "error" message so I cannot configure it.
I remember long ago I was upto some trial and error with my router and I ended up in changing some ip that I didn't know about that time, now when I was trying to forward some of the ports. I addressed the computer to 192.168.1.1 (as this was my ip that time I remember and on the box its written too) but it didn't respond, then I remember that I have changed this ip to something else and now I can't remember this.
With the risk of sounding like I'm looking for a "personal shopper", I'm looking for your opinions on a new wireless router for a small business. We already have a WatchGuard firewall. We are just looking to provide visitors and staff wireless access. We want visitors to only be able to access the internet, but we want staff to be able to access the corporate network as if they were plugged in via Ethernet. (RADIUS - AD authentication).
We have Cisco 7609 routers in our network. We are using ppp multilinks between the sites. Because of the high traffic volume, we have to use multiple multilinks. 7609 router doesn't allow ppp multlink to span SIPs, so we use multiple mulitilinks between sites on different SIPs. OSPF for load balancing will be used. THE PROBLEM IS: when we define the second ppp multilink between two 7609 routers, the new multilink stays "inactive". Can we use multiple multilinks to the same router? We have enabled the command IP CEF DISTRIBUTED, but we still face the same problem". IOS used is: 122-18.SXF6
i have a ZyXel prestige 650H-31 Model # router and i'm not able to go on to configuration page of the router i tried 192.168.1.1 several times, even after system reboot and router reset, but of no use. I've a wire connection with desktop (RJ-45 port) not USB AND MY PPPoE lights never lit. originally when i entered the gateway 192.168.1.1 it asked me for username & password, since i didn't have the password at that time i tried to reset the router but after that when ever i entered 192.168.1.1 in the browser it never came up with the option to enter user name & password. I've checked all the wires are also connected. I tried prompt command and it showed that timed out thrice and then sent= 4 received= 0 lost= 100%. I had D-Link router prior to it and later connected the D-Link router an i was able to get connected to net and browse normally.
i have a LAN network between several pc's connected with several switch's and connected to Thomson SpeedTouch 510 DSL Router its ip address is 10.0.0.100 subnet 255.0.0.0 and the router dont give auto ip to the PCs i have to issign it manually to the PCs "static ip".I bought the acer android recently so i bought a tp-link td-w8901g wireless router to act as an access point so i connected the 2 routers to each other by LAN and gave the tp-link an ip address 10.0.0.12 subnet mask 255.0.0.0 so it will be the same ip range of the speedtouch and setuped the tp-link router to fit my isp configeration it worked at first but i had to reset the router so i did the same configuration i did before but didnt work and i cant access the internet using the android or the wireless but when i connect the phone to the tp-link and unplug the speedtouch the wireless works so theres no any problem with the router?
How can I configure Belkin N1 Vision Modem router to use Back to My Mac? Bcos in iCloud preferences its give me a error message "setup router for better performance"
I am trying to configure RV082 router with Mac Native VPN Client for my remote access. However, no matter what I did, I am not able to make it works. Can any one can give me an example of how to conguration my RV082 router and Mac Book Pro(Mountain Lion)?
The router was working fine when it was setup but was disconnected for a short while. There is now no recognition of the router and the install cd was misplaced...
Currently in my office have a TPlink wireless router (WR1043N), and Dlink 615 router.Below is my office's network organization.Internet-->TPLinkRouter(192.168.2.0)-->DlinkRouter(192.168.0.0)We want to host a demo website but we are afraid our network being attacked. So we wish to implement a DMZ network to hide our internal network from outside. My question is can i setup a dmz network with the above capabilities by using home routers?
where i am from, the houses are made of conrete. so obviously my wi-fi degrades. i currently have 1 basic wireless g linksys router set up, in my bedroom as thats where the primarry devices are. there is a portion of the house where the signal is non existant and i want to set up a 2nd wireless router for that area to have signal. its a fairly large house with 4 bedrooms.here is a breakdown of the device priority:
The main room (my room, east end of house) Gaming PC (gaming, downloading, netflix streaming) non wireless Wife's Laptop (occasional streaming, general internet surfing) PS3 (gaming and netflix streaming) Ipad (streaming)
[code]....
The general purpose of all this is just have wireless across the whole house for mobility, my room is the priority as far as bandwidth usage and coverage.Also i will be purchasing an N router for my room and moving the G router to my moms.
i recently had att u vesre installed at my house with a 2 wire 3801 router/ modem but i cant get my xbox 360 online. how to configure the router for the xbox 360 so i can play xbox live.
