Looking For A Multi SSID Wireless Router
Oct 4, 2011
With the risk of sounding like I'm looking for a "personal shopper", I'm looking for your opinions on a new wireless router for a small business. We already have a WatchGuard firewall. We are just looking to provide visitors and staff wireless access. We want visitors to only be able to access the internet, but we want staff to be able to access the corporate network as if they were plugged in via Ethernet. (RADIUS - AD authentication).
View 10 Replies
ADVERTISEMENT
Dec 27, 2012
I'm using access point AIR-AP1141N-E-K9 and want to use Multi SSID. Based on Cisco document, when I config Multi SSID in access point, each SSID have a separate VLAN, is it a must have ? Can I use multi SSID without VLAN ?
View 5 Replies
View Related
Sep 25, 2012
Setup a WAP321 with the new 1.0.1.10 firmware. Setup 2 SSIDS:
WIRELESS (vlan:1)
GUEST (vlan:99)
The wap is plugged directly into a port on my router so I configured the port and additional vlan99 port. I have a DHCP scope assigned on the router to both the port and port.99 interfaces.clients on WIRELESS have no problem and work correctly, however when a client joins guest...a packet capture on the router port shows that a dhcp request is being received for the same MAC on both untagged and tagged 99 interfaces....thus it appears the WAP is not handling the vlans properly
16:07:10.566932 PortA, IN: IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from 84:c9:b2:78:fc:31, length 331
16:07:10.566947 PortA.99, IN: IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from 84:c9:b2:78:fc:31, length 331
View 2 Replies
View Related
Aug 28, 2012
Is it possible to have multi PVC for IP TV in x3000 adsl router ?
View 1 Replies
View Related
Dec 13, 2006
We have Cisco 7609 routers in our network. We are using ppp multilinks between the sites. Because of the high traffic volume, we have to use multiple multilinks. 7609 router doesn't allow ppp multlink to span SIPs, so we use multiple mulitilinks between sites on different SIPs. OSPF for load balancing will be used. THE PROBLEM IS: when we define the second ppp multilink between two 7609 routers, the new multilink stays "inactive". Can we use multiple multilinks to the same router? We have enabled the command IP CEF DISTRIBUTED, but we still face the same problem". IOS used is: 122-18.SXF6
View 21 Replies
View Related
Sep 11, 2011
I have a small business network with multiple systems on a local lan. I would like to expose two of these machine on the Internet using static IPs provided by my ISP. Both of these machines provide web services over ports 80 and 443, and thus port forwarding will not meet my needs. The way I have addressed this issue in the past is to use a router with "multi-NAT" or "many-to-many NAT" support. Alas, the router I was using is no longer working and the company no longer provides a similar offering. In speaking with CISCO customer service today, they suggested that one of the routers in the CISCO 800 series should meet my need.
So my questions are:
1. Is any out there using an 800 series router to address a similar scenario?
2. If so, is it possible to configure this scenario (e.g. Multi-nat) using the Cisco Router Web Setup (CRWS) Tool? I'm not familiar with IOS and would prefer to skip the learning curve.
View 1 Replies
View Related
Dec 1, 2011
I just reset my router to the factory settings in order to make some changes to it. However, when I tried to change the SSID to a unique name, I was unable to connect my computer to the wireless network. I then reset my security settings and left the SSID to the default name "linksys_SES_54125" and it is working just fine. I tried to connect with two separate computers both running Windows 7. My router is the WRT54G v8
why I wouldn't be able to connect to my wireless network when I change the SSID?
View 5 Replies
View Related
Aug 26, 2012
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
View 4 Replies
View Related
Mar 22, 2012
why i can not found ip router setting by main menu? the sg300-28 can not support ip router command?mor informations,see my img. If sg300-28 can not support ip router command,what i can do it that communicate by multi-Vlan ?
View 2 Replies
View Related
May 5, 2012
how i can have internet connection again. here's what happened, i disabled the Broadcasting SSID and the after that my devices can no longer locate the wifi, and then when i cant configure the setting back to its original settings because i cannot establish a connection with the mf30 and my laptop eventhough it's via USB.
View 1 Replies
View Related
Apr 19, 2012
House has 2 floors. I want to install 2 E3200, one on each floor, but both with the same SSID/Password, etc. so internet connection/streaming throughout the floor is seamless.
Both floors have network wall sockets ready and they all lead to the same modem/router so all devices plugged lead to the same network.
PS. both E3200 have been update to Firmware Version: 1.0.03
View 9 Replies
View Related
Dec 23, 2011
I will soon upgrade my wireless network from a WRT610N to an E4200v2. At setup of the router, I assume I'll be able to change the SSID of the E4200v2 and I plan to keep the same SSID as on my old router. With the same SSID as currently seen by the devices on my network
View 4 Replies
View Related
Jun 21, 2012
is it possible for a client to choose a WAN to use when being routed through a Multi-WAN router? Something that could be configured as default route in linux or default gateway in winxp ?Or is this decision totally up to the router itself ? [code] Could now a client on the subnet 192.168.0.0/24 choose 1.1.1.1 as a default route for example? And if not, could this be possible if the router hat some secondary internal IPs for both WAN interfaces.
View 3 Replies
View Related
Feb 22, 2013
I have more than 5000 sq. ft home and have some dead places other end of the house. Now I am looking for Range Extender/Repeater to boost signal. My primary wireless router is Motorola Surfboard SBG6580 and Secondary Linksys E3000 (planning to update firmware to DD-WRT). So I wanted something such that I can roam between the two routers without switching SSID (use single SSID name for primary and secondary DD-WRT routers) and connect automatically to whichever the best signal (or) strength router. In work place we have same thing like that single wireless SSID name which automatically connect wireless SSID from one end to another end of the building.
View 1 Replies
View Related
May 6, 2011
actually, i have 2wire DSL Router and i am using SSID Broadcast Disable after disable i can't connect wireless to my extra device too for example my Blackberry. but i am using another computer with wireless but i can't connect blackberry and iphone i don't have more idea in wireless stetting what can i do?
View 2 Replies
View Related
Apr 18, 2012
SSID is not being broadcast from an e3200. I split the wireless networks and assigned a new name for the 5Ghz band. The broadcast SSID button is enabled for both networks. (2.4 & 5). The idea is I want to stream video on the 5Ghz band. Nothing seems to see it though, TV other PCs, etc.
View 1 Replies
View Related
Dec 31, 2011
I cannot find the screen in the interface at 192. Where is this? Please don't say use Cisco Connect disc.
View 1 Replies
View Related
Dec 18, 2011
I just purchased an E4200 and got it up & running. Everything was fine, until I connected a Wi-Fi DVD player to it. I followed the DVD player procedure, which was to push the WPS button on the router, and then the appropriate button on the DVD player. After a few seconds, the player connected, and I successfully accessed YouTube through it.
So far, so good -- except that it turns out that the router, on its own, changed the SSID and password. When I could not get Wi-Fi access on my iPhone, I checked the Wi-Fi settings, and instead of the original SSID of the E4200 -- let's say ShadeTree -- it was changed to Cisco_WPS_xxxxx (the X's represent numbers). I started Cisco Connect, and a screen came up showing that the password had been changed from the original, and listed both the original and new passwords.
What is going on? Why would the E4200 change the SSID and password all by itself, when I connected a Wi-Fi equipped DVD player with WPS? Is this going to happen when I connect a Wi-Fi equipped TV set, or some other component? What can I do to keep the E4200 from changing the network name and password all by itself? Or am I going to have to re-program every other Wi-Fi device (iPad, iPhone, etc.) every time I add a new component?
View 6 Replies
View Related
Oct 25, 2011
I just set up a brand new LinksysE4200 router at one end of my home, and a Linksys RE1000 range expander at the other end in order to provide full WiFi coverage to my entire house. Everything is working great except for one important detail.. There is currently no way to disable SSID broadcast on the RE1000 range expander! I just flashed it with the latest firmware (v1.0.01 build 2, Jul 22, 2011) , but I'm still unable to disable it, even though it is disabled on the E4200 from which it's receiving the signal it's rebroadcasting. I am seriously considering returning the RE1000. Linksys. add the ability to disable SSID broadcast on the RE1000 in a (not too distant) future firmware upgrade! As far as I'm concerend, this is a MUST HAVE feature in order for this product to even be considered for use in any sensitive network environment.
View 2 Replies
View Related
Aug 15, 2012
I just bought a Linksys E2500, and I'm trying to configure multiple SSID's on it. The "guest mode" won't work for me because I want one SSID to use WPA and the other to use WEP, but the option to set different encryption based on the GHz frequency of the connection won't work for me because I only want the WEP one to be used by my Nintendo DS (which doesn't support WPA); I don't want to force ALL devices that don't support 5GHz to use the WEP one!
View 9 Replies
View Related
Jan 25, 2012
I have a simple configuration. E2500 using 2.x ghz N-only configuration. The router in in my office. I want to extend the same network ssid by adding another router in the kitchen, on the other side of the house. I haven't purchased the other router yet
View 1 Replies
View Related
Nov 21, 2012
How can you disable SSID broadcast on EA6500 wireless network.
View 4 Replies
View Related
Jul 28, 2011
How do I disable the broadcast of my SSID? I do not want wireless. I only bought this router to hook up two computers to the internet via Ethernet cable.
View 9 Replies
View Related
Oct 9, 2011
I've had my E3000 for almost a year now and it's been great - until recently. Latencies have become patchy for some users and most surprisingly, the 5GHz network has stopped using two channels. I did a 30/30/30 reset on it a few minutes ago and re-configured the whole thing. It's set to use 40MHz Only and WPA2 Personal, but speeds at the physical layer are still just 144 Mbps and in the web interface's Status page it clearly says "20 MHz".
Why might this be? It was fine for so long, only to refuse to use two channels now. I've checked what the other wireless networks in my area are like, and none of them are even 5GHz-capable as far as I can tell, so the relevant spectrum shouldn't be overcrowded. It's rather nice to have the two channels for NAS transfers and streaming and such.
After manually specifying a base channel (48 at the moment), it actually kicks into 40MHz. The problem is now that my clients, both using a WUSB600N, are getting "Unable to connect to (SSID)" pretty much instantly after clicking the network in Windows.
View 1 Replies
View Related
Sep 10, 2012
I have found that if I do not enable the broadcast SSID option on my 5GHz N network that my devices will forget the network and not reconnect on their own. Yet, I have the 2.4GHz G/N network set up to not broadcast my SSID and I have no problems. Why can't I disable my SSID broadcast on the 5GHz N network without these problems?
View 9 Replies
View Related
Mar 21, 2013
EA3500, I'm using the Smart Wi-Fi interface through a browser. How do I make my router broadcast the SSID? I think it was when I was setting up using the old interface, before updating the firmware, that I set it to *not* broadcast the network name. Now I feel like I've been all through the menus twice on the Smart Wi-Fi interface, and can't find the on/off toggle.
View 9 Replies
View Related
Nov 30, 2012
I had a SSID name conflict with one of my devices and the router. I changed the routers SSID which eliminated the conflict. I noted that after changing the SSID, the name of the FTP server did not update to the new SSID. Is this an issue? I did not see any way to manually edit the FTP name. FTP works fine as is.
View 1 Replies
View Related
Nov 8, 2012
Can the broadcast be disabled on EA6500?
View 1 Replies
View Related
Oct 9, 2012
I just set up my new Linksys 3200 router and wanted to know if i should turn SSID boradcasting feature off?
View 2 Replies
View Related
Jan 7, 2013
just bought the EA4500 new, setup the router with computer plug-in RJ45, after I change my network network to "LinksysOne", I can connect to the network wireless. But when I connect it with hard wire/RJ45, it shows "cisco27205", but I cannot see "cisco27205" with wifi, neither with RJ45 connection cannot see "LinksysOne". Why this happen? is this normal?
View 1 Replies
View Related
Nov 20, 2012
I got E4200 v.2 with the latest cloud firmware. On the previous (non-cloud) firmware there was an option to enable or disable SSID broadcast, and I disable it. Now I want to enable it back, but can not find this option in Cisco Connect Cloud. how to enable SSID broadcast on the E4200 v.2 with Cisco Connect Cloud firmware?
View 1 Replies
View Related
Nov 17, 2011
I have two router WRT160N & WRT120 N . They are working successfully with different SSID. Now I need one SSID. Need if found wi-fi signal week Another wi-fi take care automatically.
View 5 Replies
View Related
Aug 15, 2011
So My ssid is naular and it has password protection. However there is another ssid from my router called "linksys" which is unprotected. I tried to change it and messed it up bad. Everyime I sign on to "naular" it makes "Naular 2" then Naular 2 3 then Naular 2 3 4 etc. Then I only get local access. I look at my wireless thing and it says i'm connected to naular 2 3 4 5 when I signed onto Naular earlier.
View 1 Replies
View Related
