I'm using access point AIR-AP1141N-E-K9 and want to use Multi SSID. Based on Cisco document, when I config Multi SSID in access point, each SSID have a separate VLAN, is it a must have ? Can I use multi SSID without VLAN ?
View 5 RepliesWith the risk of sounding like I'm looking for a "personal shopper", I'm looking for your opinions on a new wireless router for a small business. We already have a WatchGuard firewall. We are just looking to provide visitors and staff wireless access. We want visitors to only be able to access the internet, but we want staff to be able to access the corporate network as if they were plugged in via Ethernet. (RADIUS - AD authentication).
View 10 Replies View RelatedSetup a WAP321 with the new 1.0.1.10 firmware. Setup 2 SSIDS:
WIRELESS (vlan:1)
GUEST (vlan:99)
The wap is plugged directly into a port on my router so I configured the port and additional vlan99 port. I have a DHCP scope assigned on the router to both the port and port.99 interfaces.clients on WIRELESS have no problem and work correctly, however when a client joins guest...a packet capture on the router port shows that a dhcp request is being received for the same MAC on both untagged and tagged 99 interfaces....thus it appears the WAP is not handling the vlans properly
16:07:10.566932 PortA, IN: IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from 84:c9:b2:78:fc:31, length 331
16:07:10.566947 PortA.99, IN: IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from 84:c9:b2:78:fc:31, length 331
Scenario: I have a vmserver w four virtual servers all in configured w in different subnets. What's the best way to configure a 3750-x switch to route traffic from the virtual servers to their vlans?
View 2 Replies View RelatedI am using an SRP541W router and i am trying to configure 2 vlans, each one to use its own Wan:Here are the dhcprules and vlans:As can be seen, each one has its own wan interface.
Vlans:As can be seen, each vlan is using its own ports and dhcp rule, so, now they should be separate.
Both Wans are connected: So now (at least as i see things) the two vlans are separate and using different Wan. But the reality is different, everything is going out using Wan1.Also in the Interface Info you can see that the 2 vlans are listed under the Wan1.
The rest of router setting are default.
why i can not found ip router setting by main menu? the sg300-28 can not support ip router command?mor informations,see my img. If sg300-28 can not support ip router command,what i can do it that communicate by multi-Vlan ?
View 2 Replies View RelatedI'm new to Cisco equipment much more familiar w/ Sonicwall w/ that said......I have a 5505 w/ Security Plus licensing
I have set up multiple VLANs as follows
VLAN 1 inside - still setup as 192.168.1.1 (will not be using this for our lan)
VLAN2 - outside
VLAN100 - LAN 10.1.1.1/24
[Code]....
If I do add all the VLANs above I understand I will probably have to make a trunk port since I only have 5 usable interfaces
is it possible to multicast between 2 different SSID's that are associated to 2 different VLAN's?
View 2 Replies View RelatedI have a WRVS4400N that broadcasts two different SSIDs. One is a public network and the second is a private network. Right now, both SSIDs are pulling from the same DHCP server, but I would like to separate the public from the private. How can I separate these SSIDs by vlans? I can't seem to get the vlans to route to separate ports.
This is my vlan settings. I have two DHCP servers right now. One is in an isolated network plugged into Port 3 of the WRVS4400N. The other is on the production network, plugged into port 1 of the WRVS4400N. For some reason, whenever I connect to SSID Public, it won't pull an IP from the DHCP on port 1, it only pulls it from the one on port 2.
I know there is three SSIDs here, the Static one is going to be the same network as the EMS one.
On ASA 5515 it shows it is in transparent mode and it has multi context.As in transparent ASA we know it has single Management IP address.This ASA is connected to one switch on two ports gi2 and gi3.One port carries vlan say 800 to the ASA.Other port carries vlan 500 from the ASA to switch But when i log onto ASA and do sh run it shows no VLan info there.
View 3 Replies View RelatedI have a switched network of C2980 & C3548 switches with multiple VLANs. I would like to understand the difference between Multi- VLAN ports and trunk ports. What circumstances would dictate using one over the other? If I configure the router port as Multi- VLAN, does the router still require sub-interfaces?
View 9 Replies View RelatedI have around 60 , 1142 N APs . As of now i have only management VLAN ( for IP ) & one user vlan 350 configured on the access point . All the users connect to VLAN 350 and they get IP as required.However in our new set up there are couple of requirements have come up were in SSID will be the same however we have created many VLANs for different kind of user group and all these VLANs should be mapped to this single SSID and pick the IPs from their respective VLANs .
We have done configuration on the RADIUS server side were in we have mapped the users in their respective VLANs and they are getting authenticated via AD . Now how do i map my these 4-5 VLANs in a single SSID in Access Point.
The environment: 20 X air-ap1141N-A-K9 (these are standalone) in three different buildings with either 1 or 2 units per floor depending on sq. footage. IOS is c1140-k9w7-tar.124-25d.JA1.
Problem Users running various tpyes of wireless cards on windows XP SP3 get disconnected periodically throughout the day whether they roam or not. This disconnect problem started happening after we replaced older 1200 series units running wpa and tkip and replaced with 1141n running wpa2 with aes. Users running windows 7 do not get disconnected. However there are very few W7 users on campus as this point in time.
I set up a single test unit shown below and associated two laptops to see if they would disconnect. Not once did I lose connectivity. NAME: "AP1210", DESCR: "Cisco Aironet 1200 Series Access Point"PID: AIR-AP1252G-A-K9 , VID: V03, SN: FTX1339903J NAME: "Dot11Radio0", DESCR: "802.11N 2.4Ghz Radio"PID: AIR-RM1252G-A-K9 , VID: V01, SN: FOC1337107F IOS: c1250-k9w7-tar.124-10b.JDA3
I've just bought an access point AP1141N for my small business but unfortunately there is only Radio 0- 2.4G available through web interface. It is working fine but I would like to have access to radio 1 (5Ghz) as well.
View 2 Replies View RelatedI have some connection trouble with AIR-AP1141N-A-K9.I put a IP camera in my home and connect to AIR-AP1141N-A-K9 via wireless.After a while about 1 week, the wireless will be dissociated.
Below are some information & log message of AP.
AP information
----
Product/Model Number: AIR-AP1141N-A-K9
Top Assembly Serial Number: FTX1533KDNF
System Software Filename: c1140-k9w7-tar.124-21a.JA1
System Software Version: 12.4(21a)JA1
Bootloader Version: 12.4(23c)JA1
[code].....
I have one cisco wlc 2112 with ios 7.0.230.0 with license to support 12 access points. My access points are nine (9) lap1231ag and one (1) lap1310.I just have one wlan (ssid). My scenario of deployment is in layer 3. I have one interface management and ap manager in the WLC. All my Access Points have differents ip address that WLC. I need to configure a unique ssid to associate my six (6) dynamics interfaces (each dymanic interface with different vlan subnet).Each wlan profile (ssid) should have the same security in phase 2 (wpa2/psk). My cisco access points don't support hreap. My wlc support only (4) interface into an interface group, and i need six (6) dynamics interfaces.
View 6 Replies View RelatedI just purchased the AP1141N and I have created a logon account to access the device via URL which works fine but after 10 minutes it logs me out and requires that I log back on. Unfortunately it won't allow me to log back on unless I reset the device then I have another 10 minutes before it asks me to login again but then it won't accept my logon again without a reset.
I can logon with my account via the console logon but I don't know how to configure the access point via command line so I use the web interface. I have disabled the timing for security but didn't work.
I want to confirm if the access point (AIR-AP1141N-E-K9) can work with the Wireless LAN Controller (AIR-CT5508-25-k9)
View 2 Replies View RelatedI have a network with several catalyst 2960 switches and one catalyst 3750. I have created two VLAN and set up the proper routing and everything is working fine there. I have a client/server application that used multicast in the initial start up for the client to determine available servers, the issue is one of my clients is on a different VLAN then the server. I am able to route the multicast using MVR as long as both the server and the client are plugged into the 3750 by creating a static route, making the server a source port and the client a receive port. Unfortunately I need the client and the server plugged in to different 2960s. My question is how do I establish multicast routing between the two and perferably do it dynamically (always route multicast traffic from one VLAN to another).
View 2 Replies View RelatedThe issue that I have is around getting second SSID work on my router! So I have created two Vlans, 30 & 200. Vlan 200 is the native and is associated to SSID "Bitter". This SSID works like a charm however the other Vlan cannot be even pinged from router side the ip that I tried to ping is 192.168.30.1. I have posted the config below. Also i tried to brak wlan-gig into sub interfaces but the IOS does not accept that!
Vlan 30 >>>RadioDot 11 0.30>>>>Gigabit 0.2>>>>bridge group 2
Vlan 200>>RadioDot 11 0.200>>>Gigabit 0.1>>>>bridge group 1 (native Vlan)
Router side:
ip source-route
!
!
!
ip dhcp excluded-address 10.10.10.1
[Code]...
I have 4 autonomous AP 1142 with 2 ssids : SSID10,vlan10 & SSID20,vlan 20.I use ACS 4.2 in order to authenticate users (EAP-FAST). How can i restrict access base on ssid or on vlan?I want users that connect to SSID 10 to not have access to SSID 20 and the opposite.
View 7 Replies View Relatedhow to change our wireless setup. Currently, we have 2 Cisco AiroNet 1130 WAP's in the office that go directly into the 2 POE ports on our Cisco ASA 5500. These WAP's have 1 SSID and are using WEP for security. After demonstrating the flaws of WEP to my boss, he has agreed that we should use something more secure and I've suggested WPA. We want visitors to our office to be able to hop on our wireless but on a separate guest SSID with WEP.
I'd like the internal SSID to route to the ASA and take the default route to the internet (it will be our new fiber connection once it's installed in a couple weeks). The default route is whichever connection is working since our ASA 5500 will fail over when it detects an outage.
I'd like the guest SSID to route to the ASA and then go over our existing cable connection. This connection will be our backup once the fiber connection is installed. Since we won't be using it very often, but will be paying for it, I advised that we send all guest wireless traffic over this connection since 50/5 is plenty for guests.
The current SSID (which will be the internal SSID) has no VLAN. We do currently have a few VLANS on our network, one for voice (.42) and one for data (.100) and the default (.0). What device to I create the VLAN on (Cisco 5500?) and how to I setup the WAP? I need very basic instructions to start and I'm also trying to do this without causing downtime if possible.
I've attached a diagram of what it should look like. Red indicates our internal network and Blue indicates the guest network. I can send screenshots as well.
I created a second VLAN and a second SSID. My problem is that from a PC on the native VLAN 1 I can ping the IP of VLAN 2 192.168.2.254 but I cannot ping any other device that has connected to the second SSID. How do I get routing to work between the two VLAN? I thought it would be automatically setup when I created the second VLAN using Cisco Configuration Professional?
View 3 Replies View Relatedi`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that
1) i`m not able to broadcast the both SSIDs in the same time from the Access point
2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
Multi brands ips in one PC?
View 1 Replies View RelatedWe have network consisting of approx. 8 7200's running LNS/MPLS/BGP and we provide predominantly private networks to clients(Majority of client networks are a mix of Ethernet tails and DSL).We have received a request from one client to support multicast - Having never implemented multicast, have a few questions:
1. Is is supported/possible to provide multicast within a vrf on 7200's?(From initial investigations, it appears to be)
2. Is it possible to only enable mutilcast in a vrf(i.e. not globally)?
3. Any recommended guides/best pratices?(Googling has revealed nothing really that is similiar to what we want to do)4. What are the potential ramifications?(Resource overhead, Security implications, anything else?)
I wish to build a test rig in my office that will act as 2 separate geographic locations with a router at each location connecting to a make believe MPLS kind of network. I then wish for these sites to communicate with each other but obviously be on separate IP ranges .I know each site would have a router and I assume that there ideally should be 2 corresponding (provider) routers on the MPLS network. What I do not know is how the the routers at each site should connect physically to its partner router at the MPLS and also how the two MPLS routers would connect together. For example, if I wanted to later scale up to have 4 geographical sites how would the 4 MPLS routers connect together (using a switch?)?
View 5 Replies View RelatedOK. I think Im going crazy here. Im studying OSPF and I'm working on the DR/BDR election process. I have a topology where three devices (RIDs 1.1.1.1, 2.2.2.2, and 9.9.9.9) are on the same ethernet segment so they need to elect a DR. 9.9.9.9 is a switch and Im using a SVI for the OSPF interface. Van't get the darn thing to show up in the post but here is the topology.URl After OSPF came up, I noticed that router2 was selected as the DR and that switch1 was selected as the BDR. I thought initially that it was a matter of timing and that perhaps router2 just came up first and the slower SVI interface came up second. Shutdown the interfaces, cleared the OSPF process, and set the OSPF router priority on the VLAN interface to 10.
View 11 Replies View RelatedI have configured my two vdsl link with ppp multilink but i am not getting the desired bandwidth. Here is my configuration is this okay or i need something more in the configuration. My router is 2921 what is the maximum WAN throughput of 2921? [code]
View 3 Replies View Relatedis there any known issue in configuring multilink ppp using an old WIC-1T and a newer HWIC-1T on the same Cisco 1841 router ?
View 2 Replies View RelatedIs it possible to install LMS 4.2 in multiserver mode but with possibility to select installed components/applications? I'm talking about Solaris version. I can't see such an option. It will install all the components on every server which I don't want to. We have LMS 3.2 working in such setup: one server with most major components, other running just DFM and third one with only HUM installed.
View 3 Replies View RelatedI'm trying to find out what platforms support Multilink PPP with Link Fragmentation and Interleaving over a single link, when that single link is PPPoE. In searching the documentation, the best information I can find is that it seems to be supported in one direction on the ASR1000 url...Many platforms appear to support PPPoE and also MLPPP w/LFI, but it's not clear that both features are supported on the same link.
The application is a radio that has an Ethernet interface on its terrestrial link, and acts as an Ethernet bridge. Would like to use Multilink PPPoE with LFI in order to provide LFI in order to run VoIP over lower speed links (e.g 256kb). For what it's worth, the radio also supports RFC 5578 PPPoE Extensions for Credit Flow and Link Metrics. It was fairly easy to find what platforms support RFC 5578. But RFC 5578 would be used to support variation in the capacity of the link. If the link speed is fixed, RFC 5578 is not needed. I was trying to find if the set of platforms supported increase if the need for RFC 5578 is taken off the table.
In particular, I'd be interested in the whether the ASR 9000 series supports MLPPP bundles with LFI when the links are PPPoE.