Cisco :: 887w VLan On SSID
Sep 24, 2011
The issue that I have is around getting second SSID work on my router! So I have created two Vlans, 30 & 200. Vlan 200 is the native and is associated to SSID "Bitter". This SSID works like a charm however the other Vlan cannot be even pinged from router side the ip that I tried to ping is 192.168.30.1. I have posted the config below. Also i tried to brak wlan-gig into sub interfaces but the IOS does not accept that!
Vlan 30 >>>RadioDot 11 0.30>>>>Gigabit 0.2>>>>bridge group 2
Vlan 200>>RadioDot 11 0.200>>>Gigabit 0.1>>>>bridge group 1 (native Vlan)
Router side:
ip source-route
!
!
!
ip dhcp excluded-address 10.10.10.1
[Code]...
View 1 Replies
ADVERTISEMENT
Oct 4, 2012
I created a second VLAN and a second SSID. My problem is that from a PC on the native VLAN 1 I can ping the IP of VLAN 2 192.168.2.254 but I cannot ping any other device that has connected to the second SSID. How do I get routing to work between the two VLAN? I thought it would be automatically setup when I created the second VLAN using Cisco Configuration Professional?
View 3 Replies
View Related
Dec 12, 2012
is it possible to multicast between 2 different SSID's that are associated to 2 different VLAN's?
View 2 Replies
View Related
Dec 27, 2012
I'm using access point AIR-AP1141N-E-K9 and want to use Multi SSID. Based on Cisco document, when I config Multi SSID in access point, each SSID have a separate VLAN, is it a must have ? Can I use multi SSID without VLAN ?
View 5 Replies
View Related
Aug 10, 2011
I have a WRVS4400N that broadcasts two different SSIDs. One is a public network and the second is a private network. Right now, both SSIDs are pulling from the same DHCP server, but I would like to separate the public from the private. How can I separate these SSIDs by vlans? I can't seem to get the vlans to route to separate ports.
This is my vlan settings. I have two DHCP servers right now. One is in an isolated network plugged into Port 3 of the WRVS4400N. The other is on the production network, plugged into port 1 of the WRVS4400N. For some reason, whenever I connect to SSID Public, it won't pull an IP from the DHCP on port 1, it only pulls it from the one on port 2.
I know there is three SSIDs here, the Static one is going to be the same network as the EMS one.
View 4 Replies
View Related
Aug 4, 2011
I have 4 autonomous AP 1142 with 2 ssids : SSID10,vlan10 & SSID20,vlan 20.I use ACS 4.2 in order to authenticate users (EAP-FAST). How can i restrict access base on ssid or on vlan?I want users that connect to SSID 10 to not have access to SSID 20 and the opposite.
View 7 Replies
View Related
Oct 15, 2010
I just received a 887W and would like to setup using the SDM.I don't know and cannot find the default IP.
View 7 Replies
View Related
Apr 2, 2013
I have around 60 , 1142 N APs . As of now i have only management VLAN ( for IP ) & one user vlan 350 configured on the access point . All the users connect to VLAN 350 and they get IP as required.However in our new set up there are couple of requirements have come up were in SSID will be the same however we have created many VLANs for different kind of user group and all these VLANs should be mapped to this single SSID and pick the IPs from their respective VLANs .
We have done configuration on the RADIUS server side were in we have mapped the users in their respective VLANs and they are getting authenticated via AD . Now how do i map my these 4-5 VLANs in a single SSID in Access Point.
View 16 Replies
View Related
May 22, 2013
I have one cisco wlc 2112 with ios 7.0.230.0 with license to support 12 access points. My access points are nine (9) lap1231ag and one (1) lap1310.I just have one wlan (ssid). My scenario of deployment is in layer 3. I have one interface management and ap manager in the WLC. All my Access Points have differents ip address that WLC. I need to configure a unique ssid to associate my six (6) dynamics interfaces (each dymanic interface with different vlan subnet).Each wlan profile (ssid) should have the same security in phase 2 (wpa2/psk). My cisco access points don't support hreap. My wlc support only (4) interface into an interface group, and i need six (6) dynamics interfaces.
View 6 Replies
View Related
May 10, 2012
configuration for wireless on the cisco 887w? i would like wireless and wired users on the same vlan if possible i am trying to bring the radio up but it says reset and down and cant get it to bring it up ( i have done vlan1, ip unmbered vlan1 bit and logged onto ap using service-module wlan-ap0 session command) Also is wpa 2 enterprise possible on the cisco 887 w ( if possible i would like it to authenticate with our acs servers on our main site)
View 8 Replies
View Related
Oct 8, 2011
I recently installed a new Cisco 887W router @ my place and everything is working like a charm but the Macbook Air! The devices that are working currently are: iPhone, iPad, HP laptop, Nokia mobile phone.I have checked two Macbook Air so far and both have the same problem with the wireless network! I even manually added the SSID to "Airport Preferred network setting" but still couldn't make it to work!So the issue is the Macbook Air can detect the SSIDs intermittently however when it detects the SSID it doesn not connect to the wireless network and it comes up with the error of "connection timeout". I have used the command "show dot11 association" to see if the Macbook air will be detected on the router side unfortunately that was in vain. The setting that I have on the router under SSID is "guest-mode" i.e. it broadcasts the SSID, security is WPA 2 with AES encyrption.
View 3 Replies
View Related
Nov 1, 2012
I have cisco router 800 series 887 VAW. WiFi is connected to all my devices through this router, i.e., Windows XP, Vista, Wii, Nexus 7 and HTC Desire S. I can access internet from all these devices. The apps which are already downloaded on my Android devices connect to internet, but the bigest problem is here:
1. Google Play does not connect (on both Nexus 7 and Desire S).
2. Chrome does not work on Nexus 7
3. Nexus 7 fails to check for any system update.
4. Fails to sync accounts.
I tried to contact to the company which gave me this router, but they told the problem lies with my tablet. But the tablet works perfectly fine with others networks and Android phone works fine with 3G and other networks.
View 5 Replies
View Related
Dec 17, 2012
how to change our wireless setup. Currently, we have 2 Cisco AiroNet 1130 WAP's in the office that go directly into the 2 POE ports on our Cisco ASA 5500. These WAP's have 1 SSID and are using WEP for security. After demonstrating the flaws of WEP to my boss, he has agreed that we should use something more secure and I've suggested WPA. We want visitors to our office to be able to hop on our wireless but on a separate guest SSID with WEP.
I'd like the internal SSID to route to the ASA and take the default route to the internet (it will be our new fiber connection once it's installed in a couple weeks). The default route is whichever connection is working since our ASA 5500 will fail over when it detects an outage.
I'd like the guest SSID to route to the ASA and then go over our existing cable connection. This connection will be our backup once the fiber connection is installed. Since we won't be using it very often, but will be paying for it, I advised that we send all guest wireless traffic over this connection since 50/5 is plenty for guests.
The current SSID (which will be the internal SSID) has no VLAN. We do currently have a few VLANS on our network, one for voice (.42) and one for data (.100) and the default (.0). What device to I create the VLAN on (Cisco 5500?) and how to I setup the WAP? I need very basic instructions to start and I'm also trying to do this without causing downtime if possible.
I've attached a diagram of what it should look like. Red indicates our internal network and Blue indicates the guest network. I can send screenshots as well.
View 2 Replies
View Related
May 28, 2013
i`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that
1) i`m not able to broadcast the both SSIDs in the same time from the Access point
2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?
View 2 Replies
View Related
Aug 26, 2012
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
View 4 Replies
View Related
May 12, 2011
We are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies
View Related
Jan 12, 2013
How do I submit an RFE (Request For Enhancement) to the Cisco SBR team to encourage them to implement the missing support for VLAN to VLAN firewall rules that was available in the RVS4000 (See [URL]) and that was supposedly added to a beta release of the RV220W firmware (See [URL])?
View 1 Replies
View Related
Jan 10, 2012
Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies
View Related
Jan 10, 2013
I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
View 4 Replies
View Related
Aug 12, 2012
We have 6509 VSS with FWSM Module and we have created two context on it, one is INTERNALL CONTEXT othe is EXTERNALL Context? We have spanned various VLANS in switches and FWSM context level. All VLAN Gateways are configured in context level.
Activity description : We had planned migration of these devices into a new Datacenter, it was a planned activity. During migration of devices from one Dc to a new DC we broke the VSS and kept the primary running and removed the secondary switch and migrated this secondary to new DC and powered this device ON in the new DC and checked all the config was very much fine but this device was OFF network as secondary was brought to new DC just to limit the downtime during the primary switch movement.
During the activity ( Primary switch movement )We powered off the Primary switch and mean time before shifting into new Data center We had brought up secondary switch which was already existing in the DC was put live in the network and it was working fine without any issues.
Later we had moved Primary into new data center and tried to put into VSS with the secondary , during this period the secondary device into went into RECOVERY MODE and primary device was not responding and devices went off network and immediatly we removed the VSL link and brought up primary into production network without secondary online in the network ( Without VSS just stand alone switch ) network started working, but bringing up the primary we found that some of the VLANS in the FWSM was deleted and some VLAN had misconfiguration ( example : say original VLAN ip 10.200.112.1 has become 10.300.13.1 ) also some of the access list as well as SVI was deleted making configuration mismatch.
Wanted to know while syncronization b/n primary and secondary switch in VSS if we pull out VSL link would create this type of issues.
View 1 Replies
View Related
Feb 2, 2011
I have set up 2 DHCP pools and 2 VLANs (1 *the native* for data / 1 VLAN for voice). When I use the command "switchport voice vlan 20" the port disapear from the show vlan brief list. When I use the "switchport access vlan 20" it shows up in the show vlan brief in the correct VLAN and gives the phone an IP. I assume that using the access instead of the voice is wrong and the phones would not configure correctly. But when I use the access the phone goes to the next step and tells me the TFTP files are not found. Why does the port disapear from the VLAN list?
View 8 Replies
View Related
Mar 31, 2013
i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
View 4 Replies
View Related
Sep 16, 2012
I have a 3750G switch in my production network that only has VLAN 1 on it. All ports are in a default state and VLAN 1 is disabled. The switch is passing traffic but shouldn't having the default VLAN shut down cause the ports not to pass traffic? If I start to create VLANs will that cause the switch to stop passing traffic?
View 4 Replies
View Related
Oct 12, 2011
I'm wanting to setup a Virtual Office scenario. Everything is working fine except for 802.1x...I can get the 881 to authenticate things connected to it, but I don't have the options of guest-vlan or auth-fail vlan.Idea is if the users takes the router home and someone, either accidentally or on pupose, connects an unauthorized Laptop, they stay off the Corp network but can get to the internet still.I found this link on Cisco's site: [URL]That link shows them configuring a guest vlan right on the fa0-3 ports of an 881W. I dont have that option on mine. I can only configure 802.1x on the vlan interface. I have 802.1x working, for things that connect to vlan1, but I would like to have a "fallback" setup.
EZVPN_Remote(config-if)#int fa1
EZVPN_Remote(config-if)#dot
EZVPN_Remote(config-if)#dot1?
dot1q
EZVPN_Remote(config-if)#dot1
[code]....
View 1 Replies
View Related
Jun 13, 2011
I am trying to setup a L2tpv3 VLAN-to-VLAN tunnel.My setup has two Cisco 890 router with Cisco IOS Software version 15.0(1) M4. These routers are connected directly on FastEthernet port 8.
One linux machine is connected on FastEthernet port 0 on each router. The two linux machines are on same vlan. I am trying to establish a vlan-to-vlan tunnel between the routers and send traffic between the linux machines.
I followed the case study 11.4 from [URL] and configured the l2tp-class and pseudowire-class. However, the vlan interface configuration is different on 890 router.
I configured a vlan interface as follows.
(config)#vlan 200
(config)# interface FastEthernet 0
#shutdown
#switchport access vlan 200
(config)# interface vlan 200
I don't see the 'xconnect' command in this context. What's wrong with my configuration?
View 3 Replies
View Related
Nov 20, 2012
We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
Here are the Layer 3 Design:
Client -> vlan 2 - Switch - vlan 7 -> vlan 1 - ASA 5505 -> ISP
The Layer 2 Design:
Client -> Gig2/0/13 - Switch - Gig4/0/43 -> Eth0/1 ASA5505 -> ISP
IP Address:
Client: 172.16.2.10Vlan2: 172.16.2.1Vlan7: 172.16.7.1ASA: 172.16.7.2
I assuming the switch has a problem with routing ?It is a stacked Switch with following members:
switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-24tsswitch 3 provision ws-c3750g-24tsswitch 4 provision ws-c3750x-48
And we have following error message in the log from the switch:
%PLATFORM_UCAST-4-PREFIX:
One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue.
Here are the relevant config:
ASA Interface on the Switch:
interface GigabitEthernet4/0/43description ASA-inside LANswitchport access vlan 7switchport mode accessspanning-tree portfast
Client Interface on the Switch:
interface GigabitEthernet3/0/1switchport access vlan 2switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable
[code]...
View 2 Replies
View Related
Nov 21, 2012
i'm going mad on following problem. I'm trying to get 2 networks seeing each other while one of the network is a non VLAN network and the other one is a VLAN network.They should use the same interface so i added VLAN e0/0.122 to the interface e0/0.Send a ping from my asa to both gw-IP's made me happy at first. In second in figured out that i cannot reach any client in the other network. For testing purpose i created an permit acl to any/any for both networks, but the packets still get dropped by the default implicit rule. (deny any/anyMaybe i'm to stupid for this
View 10 Replies
View Related
Nov 27, 2012
I am trying to set up a Vlan on an SF-302-08 small business switch. I would like two Vlans both with internet access but the two cannot communicate with each other. I am not really sure how to go about setting this up as its all fairly new to me. I have successfully set up the Vlans and the ports on each VLAN cannot communicate with each other however the internet access will only work when plugged into either VLAN but wont work on both together
View 1 Replies
View Related
Jan 23, 2013
I've been given the task to clean-up our network config, and have walked into a disaster zone.We have a 4510R on site with everyone using the default VLAN, VLAN 1.I have created 4 new VLANS, VLAN100, VLAN150, VLAN200, VLAN250 I have assigned interface addresses to each VLAN and configured Inter VLAN routing.I can route to and from each new vlan with no problem, i.e VLAN250>VLAN100 VlAN100>VLAN200 etc but I can't route to VLAN 1(Default VLAN) from any of them, I can ping the interface on VLAN 1 from any VLAN , but any hosts are unreachable. On the flip side , from VLAN 1 I can route to all of the VLANS.
View 3 Replies
View Related
Apr 6, 2013
I have some problem in my small network.I have 2 SF-300 48 port switches and connected to 847 router for intervlan routing. I configure 7 vlan in SW1 and uplink to SW2 with trunkport.
The problem is that if i used default gateway for users ip address of interface (vlan interface) is ok. I bring two adsl modem and connected to vlan1 and vlan2 for internet access. When i connected this two modem vlan 1 and vlan 2 are not going to access other vlan 3,4,5,6,7 and wise versa.
vlan1 users getting default gateway from adsl modem ip, how i can permit this two vlan should to access other vlan 3,4,5,6,7 and 3,4,5,6,7 should access to internet also.
[URL]...
View 4 Replies
View Related
Jan 20, 2011
I have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
View 3 Replies
View Related
Nov 23, 2011
I have one NAM 2204 upgraded to 5.1.2 version, but in Monitor - Traffic Summary - TOP N VLAN appears only VLAN 0, Why?
View 1 Replies
View Related
Dec 26, 2012
I have a strange error in Cisco CISCO892W-AGN-E-K9 that i bought for our clients a month back.
- the router doesn't display the SSID for a longer period. Its like on and off of the SSID, showing sometimes and sometimes blank for the same device (Laptop/ Mobile/ or other Wireless Devices) within the range.
The router is in my office, but sometimes my laptop is connected, and sometimes it does not connect, and it is same with my other friends laptop.
Is it a problem with the device, configuration or the IOS issues?
View 4 Replies
View Related
