Cisco AAA/Identity/Nac :: 802.1x Auth-Fail VLAN And Guest-VLan Not Available
Oct 12, 2011
I'm wanting to setup a Virtual Office scenario. Everything is working fine except for 802.1x...I can get the 881 to authenticate things connected to it, but I don't have the options of guest-vlan or auth-fail vlan.Idea is if the users takes the router home and someone, either accidentally or on pupose, connects an unauthorized Laptop, they stay off the Corp network but can get to the internet still.I found this link on Cisco's site: [URL]That link shows them configuring a guest vlan right on the fa0-3 ports of an 881W. I dont have that option on mine. I can only configure 802.1x on the vlan interface. I have 802.1x working, for things that connect to vlan1, but I would like to have a "fallback" setup.
EZVPN_Remote(config-if)#int fa1
EZVPN_Remote(config-if)#dot
EZVPN_Remote(config-if)#dot1?
dot1q
EZVPN_Remote(config-if)#dot1
[code]....
View 1 Replies
ADVERTISEMENT
Jul 15, 2012
when the supplicant is missing vlan500 is open for port and everything is ok, but when supplicant has wrong configuration something happend and port is always authenticating(every 30s, vlan500 is not assign to this port with bad configuration supplicant) and logs show something like that
Jul 10 10:20:12.362: %AUTHMGR-5-START: Starting 'dot1x' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A3545161E4 Jul 10 10:20:44.365: %AUTHMGR-5-START: Starting 'mab' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %MAB-5-FAIL: Authentication failed for client (001e.3718.7297) on Interface Ga0/1AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'mab' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %AUTHMGR-7-FAILOVER: Failing over from 'mab' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %AUTHMGR-5-START: Starting 'dot1x' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11
version - Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 15.0(1)SE2
port config:
interface GigabitEthernet0/1
switchport access vlan 104
switchport mode access
switchport voice vlan 200
authentication event fail action authorize vlan 500
[code]....
View 3 Replies
View Related
Jul 13, 2011
is it possible to set the dot1x guest-vlan on a Catalyst Switch via ACS 5.2 dynamicly. I want to make MAB with known Devices (FAT-Clients, Notebooks, Desktops, Printers) and unknown Devices.I will set the VLAN dynamicly with dot1x per ACS. For known FAT-Clients, Notebooks etc. it's running well.But for Printers it's more difficult because I have about 500 Printers in several IP-Segments on several Switches and I will not make to much Rules in ACS for Grouping, Mapping and Authority-Rules.My Idea is to set the Guest-VLAN on every Switch, read them with ACS and use this for my Printers.The Problem is that Guest-VLAN is set on more than 100 Switch and this guest-vlan is different on any Switch.Can I read the Geust-VLAN Value so that I can set this via ACS ?
View 4 Replies
View Related
Apr 9, 2012
I have a 2960 sw configured for dot1x authentication, the problem is the Guest VLAN and Restricted VLAN didnot work. The switch port was stuck in authenticating status. The server is Juniper IC4500.
View 2 Replies
View Related
Oct 10, 2012
I've configured an ACS 5.3 system and all my groups etc fucniton corrcetly both for Network Access and for Device Administration.
However I'm stuck trying to allow clients to authenticate against the router's web-page i.e. Web-Authenticaiton, using TACACS+ between the router and the ACS5.3.
I've looked into this and I need to configure a custom-attribute of "service" with type Outbound and link this to an Authorization policy.
View 3 Replies
View Related
Apr 17, 2011
I would like to configure a guest-vlan and restricted-vlan on a 2960 switch, but I can not.
I am trying to configure the interface using the following commands: [code] similar result is obtained while trying to configure a auth-fail vlan. the full configuration file is attached.
View 4 Replies
View Related
May 18, 2013
I am configuring 802.1X in a 3560 Switch, my Radius server is a Microsoft IAS, when I connect a station of a guest user, the guest-vlan is not assigned in the port, and I have these logs:
May 8 21:23:02: dot1x-ev:Received an EAP Timeout on FastEthernet0/8 for mac 0000.0000.0000
May 8 21:23:02: dot1x-ev:dot1x_guest_vlan_applicable: Guest VLAN not
[Code].....
View 7 Replies
View Related
Aug 29, 2011
I have configured a qos policy and I am trying to apply the policy to a vlan interface which is physically connected to a switch module port of a 3845 Router.When I try to apply, the message configuration failed appears.
View 4 Replies
View Related
May 2, 2011
I have three 5508 WLCs, running code 7.0.98.0 supporting 100+ LWAPs in H-REAP mode. The LWAPs are servicing 2-3 WLANs each. Some are using central authentication and local switching, some are configured for central authentication and central switching. When the LWAPs fail from one WLC to another WLC, the LWAP's lose all of their VLAN mappings and pick up the VLAN of the management interface on the new WLC.
All WLANs are configured to use the management interface on the WLC and the VLAN mappings are configured per LWAP on the H-REAP properties tab. The WLAN ID numbers and all the WLAN settings are the same across all 3 WLC's. I have created AP groups on all 3 WLC's and the AP group config matches across the 3 WLCs.
I can get the LWAPs to keep their VLAN mapping by creating an interface on the WLC with the VLAN ID of the locally switched/remote site VLAN and then setting the interface for the WLAN to the new interface. However, then the WLAN doesn't work, because the centrally located WLC doesn't have the remote site VLAN. It also seems to keep the VLAN mapping if I create the locally switched/remote site VLAN interface on the WLC , and point the WLAN to the management interface. This shouldn't be a necessary step though... In H-REAP with local switching, the LWAPs aren't using the interface on the WLC.
I found a note in the 7.0 WLC config guide that explains why the VLANs are picking up the management interface VLAN, but that same note says the VLAN mappings can be changed per LWAP/WLAN!
From config guide: For hybrid-REAP access points, the interface mapping at the controller for WLANs that is configured for H-REAP Local Switching is inherited at the access point as the default VLAN tagging. This mapping can be easily changed per SSID, per hybrid-REAP access point
Using H-REAP and been able to get the LWAPs to keep the VLAN mapping when failing from one WLC to another?
View 9 Replies
View Related
Apr 15, 2012
I know "Guest Vlan" aren't available on SG200, only SG300 have that feature.Problem is i only have a SG200 on hand and no extra budget.
We have multiple vlan:
vlan10: LAN
vlan20: Voice
vlan30: Guest
vlan50: Servers
vlan100: Lab1
vlan200: Lab2
Since it's a small business and lot of people moving around, doing test, etc.... most port are tag with all vlan. Our Wireless AP have multiple SSID one with vlan10 and one with vlan30 for guest.
Is there any way without the "Guest vlan" feature that i could have with my equipment any equipment without a vlan configuration be set on vlan30 ?
View 15 Replies
View Related
Nov 27, 2011
I am primarely enquiring whether the setup I have explained below is actually possible, and if so then how I can set this up. I know it isn't the easiest configuration and I need to set this up without purchasing any more equipment if at all possible.I have a Cisco SG 300-28 setup with three VLAN's. [code] Default Gateway is 192.168.10.1 (Netgear Router)I have a Wireless network setup (Netgear WMS and 2 WAP's) configured with the TWO VLAN's (1 and 3). These go into ports on the Cisco SG 300-28 which are tagged on both VLAN's. The Business wireless worked fine but the guest network didn't reout out to the internet.After some troubleshooting I realised the reason the guest wasn't working was because there was no route back from the internet to the router.
The router I have isn't really ideal, it is a Netgear DGN2200, but I managed to create a static route to 192.168.30.1 with a metric of 2, with 192,168,10.254 being the hop. Success, the connection worked, the only problem is that now my guest network can see my business network because the business network is using the static route on my router to route back over to the guest network (due to the limitations of this device I can't do anything about that)Guest network can connect to Business VLAN via switch. I am assuming this is because the router is on the Business VLAN and the default gateway is the router. As they are on the same network the Guest network can inevetably see the business server and network.The Business network can get back to the Guest network via the router using my static route I created. The static route is really basic and I can't create a firewall rule on the router to prevent the Business network speaking to guest network because it only has a LAN - WAN firewall and this connection is LAN - LAN.
What I need is...to somehow stop any traffic from the 192.168.30.0 network routing to anything on the 192.168.10.0 network, appart from the router on 192.168.10.1.Is this possible? I have this setup on a number of different site, the only difference is I have a CIsco Security Router on these with the VLAN's configured so I don't have this problem. Because I have a rather limited Netgear DGN2200 I am unable to setup the VLAN's correctly and as such I need to see if I can do this on the switch in any way.
View 2 Replies
View Related
Sep 6, 2012
My company has an RV180W Router, a SGE-2000 Managed Switch, and a WAP321 Wireless Access Point. I have about 12 users on a Windows 2003 Server Standard, completely updated. My Win box is my DHCP Server. Now I am running two VLANS, Vlan 1 (default) the main vlan is where the Win box is on. Vlan 5 (guest Vlan) uses the RV180W as the DHCP server.
-Vlan1 is 192.168.1.1-254 - Issued by Win box
-Vlan5 is 192.168.2.100-254 - Issued by RV180W
View 3 Replies
View Related
Mar 26, 2013
I have registered here to clarify some things about VLAN's. There are so many (different) names and mentions that i found tat my vision gets blurry looking through all the info.I have a setup at a client where the Guest WiFi access needs to be separated from the normal LAN where all the normal devices are attached to. The guests are not allowed to reach the IP camera's and printer etc. etc. . I am trying to visualize how the traffic should flow but the Tagged, Untagged, PVID, Trunks and other names that i found make it difficult for me to see how it works together.
View 8 Replies
View Related
Feb 10, 2012
I am running a /24 network in Active Directory with my ASA acting as gateway and firewall. Standard interfaces (Ethernet 0/0 as outside, Ethernet 0/1 as inside)
As of now I have no VLans set up, but I need to setup wireless Internet access for guests... I need directions on how to setup a Vlan with its on DHCP for these aguests... I can then make sure that my APs can be pointed to the same VLAN... I am not familiar with CLI, have generally used ASDM. I am currently running ASDM 6.3(1) on an ASA with version 8.3(1).
This is something I need to do quickly as we are expecting 20-40 "guests" shortly, and I don't want them to use our internal DHCP server addresses.
View 3 Replies
View Related
Jan 27, 2011
I have a AP541N connected to a UC560. We are currently configured for Wireless Voice and Data. We have added a Guest VLAN, but don't see where in CCA to secure the VLAN from accessing the other other two default VLANs.
Additional Info: AP541N-K9-1.7(2)UC560 15.0(1)XA2, RELEASE SOFTWARE (fc2)CCA 3.0
View 1 Replies
View Related
Jun 23, 2012
I have some Cisco 1240 Access Points which are not centrally managed. I want to add 802.1Q trunking so as to be able to provision a guest VLAN. But a trick is that these APs are in some very high ceilings. I would like to provision the new trunking and guest VLAN without having to remove them from the ceiling. Someone suggested I just make the native VLAN save as existing and make the port to which attaches a trunked port. But when I did this I lost connectivity to the Access Point. Access came back as soon as I made the switch port an access port. how I can add the trunking and guest VLAN without having to get into the ceilings to remove them and configure them via console or other?
View 2 Replies
View Related
Apr 8, 2013
Any issue creating a guest vlan to use the WIFI on an 891W router? The IOS is version 15.1. I have created discreet Vlan's and setup subinterfaces on both the WLAN_AP0 and GigaEthernet 0 interfaces with dot1q encapsulation. The client will receive an IP from the pool but cannot ping or connect beyond the default gateway.
The external interface is using Nat overload and all wired clients are successful in connecting to outside addresses. I have insert a permit any statement in the acl which affects the external port but still no success.
View 7 Replies
View Related
Jul 11, 2012
Hardware: Cisco 3750 switch and Cisco autonomous access point (AIR-AP1142N-E-K9).Requirement: A single broadcast SSID; use dot1x to assign vlan 98 to authenticated clients (computer certificate); assign vlan 3 (guest) if the authentication fails.I can achieve assigning a guest vlan on authentication failure when using a wired connection by using the following command on the interface:authentication event fail action authorize vlan 3 I'm after a way to achieve the above using the wireless access point. The main point is that internal users cannot access vlan 3 as they have a valid certificate and that guests do not have to authenticate.
View 2 Replies
View Related
Feb 23, 2012
In our test set up, we have two WLC 5508 Controllers connected via Checkpoint UTM-1 firewall Inside and DMZ Interfaces. Both the WLC controllers are connected to the firewall via Cisco 3750 switch. On the Local (Inside) Controller, guest SSID is enabled and attached to the wireless management Interface. On the remote anchor controller, guest SSID is enabled and attached to the Management Interface as well. The following configs are replicated on both the Controllers.
SSID Name - guest
Interface - Management ( VLAN 10 on Local and VLAN 20 on remote) -
Mobility Group: Same configs at both ends
SSID Anchor : Anchor SSID on local and local SSID on Anchor.
AP: CAPWAP 3502 Management Subnet
[code]....
Is there any thing missing in the wireless configs and or the firewall rules as i could not see DHCP request back from the Anchor Controller. Also, after DHCP is obtained, the web authentication request will be redirected to an Amigopod device for authentication. In this case is the redirect URL congiguration to be performed only on the Anchor Controller or is this to be replicated on both the Local and Anchor Controllers.
View 8 Replies
View Related
Mar 6, 2012
We are trying to setup a WAP4410N with 2 SSID's. One SSID for our private network and the other for guest internet access. On the VLAN and QoS page there is a setting for priority. What would be the suggested values for this setting? We obviously want our private network to receive priority over our guest network.Also, does VLAN Tag setting need to be on Tagged to determine private from guest traffic?
View 2 Replies
View Related
May 12, 2011
We are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies
View Related
Jan 12, 2013
How do I submit an RFE (Request For Enhancement) to the Cisco SBR team to encourage them to implement the missing support for VLAN to VLAN firewall rules that was available in the RVS4000 (See [URL]) and that was supposedly added to a beta release of the RV220W firmware (See [URL])?
View 1 Replies
View Related
Jan 10, 2012
Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies
View Related
Jan 10, 2013
I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
View 4 Replies
View Related
Aug 12, 2012
We have 6509 VSS with FWSM Module and we have created two context on it, one is INTERNALL CONTEXT othe is EXTERNALL Context? We have spanned various VLANS in switches and FWSM context level. All VLAN Gateways are configured in context level.
Activity description : We had planned migration of these devices into a new Datacenter, it was a planned activity. During migration of devices from one Dc to a new DC we broke the VSS and kept the primary running and removed the secondary switch and migrated this secondary to new DC and powered this device ON in the new DC and checked all the config was very much fine but this device was OFF network as secondary was brought to new DC just to limit the downtime during the primary switch movement.
During the activity ( Primary switch movement )We powered off the Primary switch and mean time before shifting into new Data center We had brought up secondary switch which was already existing in the DC was put live in the network and it was working fine without any issues.
Later we had moved Primary into new data center and tried to put into VSS with the secondary , during this period the secondary device into went into RECOVERY MODE and primary device was not responding and devices went off network and immediatly we removed the VSL link and brought up primary into production network without secondary online in the network ( Without VSS just stand alone switch ) network started working, but bringing up the primary we found that some of the VLANS in the FWSM was deleted and some VLAN had misconfiguration ( example : say original VLAN ip 10.200.112.1 has become 10.300.13.1 ) also some of the access list as well as SVI was deleted making configuration mismatch.
Wanted to know while syncronization b/n primary and secondary switch in VSS if we pull out VSL link would create this type of issues.
View 1 Replies
View Related
Feb 2, 2011
I have set up 2 DHCP pools and 2 VLANs (1 *the native* for data / 1 VLAN for voice). When I use the command "switchport voice vlan 20" the port disapear from the show vlan brief list. When I use the "switchport access vlan 20" it shows up in the show vlan brief in the correct VLAN and gives the phone an IP. I assume that using the access instead of the voice is wrong and the phones would not configure correctly. But when I use the access the phone goes to the next step and tells me the TFTP files are not found. Why does the port disapear from the VLAN list?
View 8 Replies
View Related
Mar 31, 2013
i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
View 4 Replies
View Related
Sep 16, 2012
I have a 3750G switch in my production network that only has VLAN 1 on it. All ports are in a default state and VLAN 1 is disabled. The switch is passing traffic but shouldn't having the default VLAN shut down cause the ports not to pass traffic? If I start to create VLANs will that cause the switch to stop passing traffic?
View 4 Replies
View Related
Jun 13, 2011
I am trying to setup a L2tpv3 VLAN-to-VLAN tunnel.My setup has two Cisco 890 router with Cisco IOS Software version 15.0(1) M4. These routers are connected directly on FastEthernet port 8.
One linux machine is connected on FastEthernet port 0 on each router. The two linux machines are on same vlan. I am trying to establish a vlan-to-vlan tunnel between the routers and send traffic between the linux machines.
I followed the case study 11.4 from [URL] and configured the l2tp-class and pseudowire-class. However, the vlan interface configuration is different on 890 router.
I configured a vlan interface as follows.
(config)#vlan 200
(config)# interface FastEthernet 0
#shutdown
#switchport access vlan 200
(config)# interface vlan 200
I don't see the 'xconnect' command in this context. What's wrong with my configuration?
View 3 Replies
View Related
Nov 20, 2012
We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
Here are the Layer 3 Design:
Client -> vlan 2 - Switch - vlan 7 -> vlan 1 - ASA 5505 -> ISP
The Layer 2 Design:
Client -> Gig2/0/13 - Switch - Gig4/0/43 -> Eth0/1 ASA5505 -> ISP
IP Address:
Client: 172.16.2.10Vlan2: 172.16.2.1Vlan7: 172.16.7.1ASA: 172.16.7.2
I assuming the switch has a problem with routing ?It is a stacked Switch with following members:
switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-24tsswitch 3 provision ws-c3750g-24tsswitch 4 provision ws-c3750x-48
And we have following error message in the log from the switch:
%PLATFORM_UCAST-4-PREFIX:
One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue.
Here are the relevant config:
ASA Interface on the Switch:
interface GigabitEthernet4/0/43description ASA-inside LANswitchport access vlan 7switchport mode accessspanning-tree portfast
Client Interface on the Switch:
interface GigabitEthernet3/0/1switchport access vlan 2switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable
[code]...
View 2 Replies
View Related
Jan 20, 2011
I have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
View 3 Replies
View Related
Nov 21, 2012
i'm going mad on following problem. I'm trying to get 2 networks seeing each other while one of the network is a non VLAN network and the other one is a VLAN network.They should use the same interface so i added VLAN e0/0.122 to the interface e0/0.Send a ping from my asa to both gw-IP's made me happy at first. In second in figured out that i cannot reach any client in the other network. For testing purpose i created an permit acl to any/any for both networks, but the packets still get dropped by the default implicit rule. (deny any/anyMaybe i'm to stupid for this
View 10 Replies
View Related
Nov 27, 2012
I am trying to set up a Vlan on an SF-302-08 small business switch. I would like two Vlans both with internet access but the two cannot communicate with each other. I am not really sure how to go about setting this up as its all fairly new to me. I have successfully set up the Vlans and the ports on each VLAN cannot communicate with each other however the internet access will only work when plugged into either VLAN but wont work on both together
View 1 Replies
View Related
