I am configuring 802.1X in a 3560 Switch, my Radius server is a Microsoft IAS, when I connect a station of a guest user, the guest-vlan is not assigned in the port, and I have these logs:
May 8 21:23:02: dot1x-ev:Received an EAP Timeout on FastEthernet0/8 for mac 0000.0000.0000
May 8 21:23:02: dot1x-ev:dot1x_guest_vlan_applicable: Guest VLAN not
[Code].....
The Wireless_Employees authorization profile,assign vlan 666 for wireless employees.ISE is passing VLAN 666 to the WLC - see attachement Radius Auth-VLAN666.jpg then I look on the WLC at a wireless employee who has successuflly connected to the network, WLC is still placing him in the pre-configured VLAN 7.
1. can VLAN be pushed from ISE to the WLC (code 7.2.103) for specific user session?
When the users connect their laptop they are getting a authentication prompt but the switch is not changing the VLANs on the port after successful authentication.Below are the logs on the switch
Jan 28 2013 17:21:32.417 CST: RADIUS: Framed-MTU [12] 6 1500
Jan 28 2013 17:21:32.417 CST: RADIUS: Called-Station-Id [30] 19 "E4-D3-F1-0B-C6-0A"
Jan 28 2013 17:21:32.417 CST: RADIUS: Calling-Station-Id [31] 19 "84-8F-69-A8-BD-1D"
Jan 28 2013 17:21:32.417 CST: RADIUS: EAP-Message [79] 45
[code]....
I`m working on Dynamic Vlan Assigmenton the basis of end user authenticatedwhoc are part of specific AD Group in c ampus enviorment.Objective: Need to assign the vlan on switch port on the basis of authenticated users OU Group in Active Directory. Eg: There are 2 OU groups in AD, Sales and Administration. Authenticated user in Sales group should get Vlan 10 and user in Admininstration Group shoudl get Vlan 20.
Components:
Cisco 3750x/Cisco 4500
ACS Version 5.2
Microsoft AD
I'm trying to use 802.1x to authenticate clients on my network with dynamic VLAN assignment from RADIUS. We have IP-Phones(powered by PoE) that only supports EAP-MD5, and we would rather use MAB(it also uses LLDP-MED for some settings) to authenticate the phones using the MAC-range from the phones vendor. The following scenario works perfect:Connect the phone and let it boot up(takes a while) and authenticate with MAB.Connect a computer in the phones data-port and let it authenticate with 802.1x(or fail and reach guest-vlan) However, the following scenario doesn't work:The computer is already connected to the phoneThe phone is then connected to the switch What happends now is that the computer is authenticated using 802.1x before the phone boots up and get's authenticated with MAB. When the phone is ready, it's authenticated with MAB and everything works. However, after a short period(let's say a minute), using `debug authentication all`, we see a "NEW LL MAC: phones mac" message(which is weird since the mac has already been MAB-authenticated), and then we are unable to contact the phone using ping. When I check `show mac address-table` it has now moved the mac from `Port Gi 0/12` to `Port Drop`. However, if I check `show mab interface Gi 0/12` or `show authentication sessions` it lists the phones-mac as `mab auth sucess `.why the first scenario works, and not the second?
The switch is a 3560E PoE 24p with IOS 12.2.58SE2. Sample of the switch-config: network-policy profile 1voice vlan 90!interface GigabitEthernet0/12switchport mode accessnetwork-policy 1authentication control-direction inauthentication event fail retry 1 action authorize vlan 60authentication event server dead action authorize vlan 60authentication event no-response action authorize vlan 60authentication event server alive action reinitializeauthentication host-mode multi-domainauthentication order mab dot1xauthentication priority mab dot1xauthentication port-control autoauthentication periodicauthentication violation replacemabdot1x pae authenticatordot1x timeout tx-period 5dot1x max-reauth-req 1spanning-tree portfast!Btw, when we tried authenticating the phones using 802.1x too (EAP-MD5), there are NO problems in any of the scenarios. However, we want to use MAB instead of 802.1x to avoid the requirement of configuring the phones with a username and password. The RADIUS response was the same when using 802.1x as it is with MAB for the phones (including device-traffic-class=voice AV-pair).
I'm wanting to setup a Virtual Office scenario. Everything is working fine except for 802.1x...I can get the 881 to authenticate things connected to it, but I don't have the options of guest-vlan or auth-fail vlan.Idea is if the users takes the router home and someone, either accidentally or on pupose, connects an unauthorized Laptop, they stay off the Corp network but can get to the internet still.I found this link on Cisco's site: [URL]That link shows them configuring a guest vlan right on the fa0-3 ports of an 881W. I dont have that option on mine. I can only configure 802.1x on the vlan interface. I have 802.1x working, for things that connect to vlan1, but I would like to have a "fallback" setup.
EZVPN_Remote(config-if)#int fa1
EZVPN_Remote(config-if)#dot
EZVPN_Remote(config-if)#dot1?
dot1q
EZVPN_Remote(config-if)#dot1
[code]....
is it possible to set the dot1x guest-vlan on a Catalyst Switch via ACS 5.2 dynamicly. I want to make MAB with known Devices (FAT-Clients, Notebooks, Desktops, Printers) and unknown Devices.I will set the VLAN dynamicly with dot1x per ACS. For known FAT-Clients, Notebooks etc. it's running well.But for Printers it's more difficult because I have about 500 Printers in several IP-Segments on several Switches and I will not make to much Rules in ACS for Grouping, Mapping and Authority-Rules.My Idea is to set the Guest-VLAN on every Switch, read them with ACS and use this for my Printers.The Problem is that Guest-VLAN is set on more than 100 Switch and this guest-vlan is different on any Switch.Can I read the Geust-VLAN Value so that I can set this via ACS ?
View 4 Replies View RelatedI have a 2960 sw configured for dot1x authentication, the problem is the Guest VLAN and Restricted VLAN didnot work. The switch port was stuck in authenticating status. The server is Juniper IC4500.
View 2 Replies View RelatedI've configured an ACS 5.3 system and all my groups etc fucniton corrcetly both for Network Access and for Device Administration.
However I'm stuck trying to allow clients to authenticate against the router's web-page i.e. Web-Authenticaiton, using TACACS+ between the router and the ACS5.3.
I've looked into this and I need to configure a custom-attribute of "service" with type Outbound and link this to an Authorization policy.
I installed NGS 2.0.2 for wireless guest user management and authentication. I implement webauth via webauth page on wlc deployed.One Branch with a WLC5508 version 7.0 wireless anchor controller is working on the NGS.But now I integrate next branch with WLC4402 version 6.0.188 and the authentication of users at the new branch gets an error, wrong user/password.
I double checked configuration and user/password but I can't find any configuration error. Also stopping and starting of radius service and reboot of NGS still does not work. I tried to debug the radius via web interface and watched for the loggfile and there is still a reject.I also tried the freeradius command radiusd -X but I got an error when starting the radiusd -X.
1.) How can I figure out, if I will get the correct password from my WLC ? Are there any debug options to see more ? e.g. some cli commands, radiustest utilities or how to get the received password from the chap challenge of the debug ?
2.) I have appended a part from my radius loggfile. How can I find the detailed error in the radius log file? Is it correct that the password in the debug file is empty ? raiuds logg line "[radius-user-auth] expand: %{User-Password} -> "
I would like to configure a guest-vlan and restricted-vlan on a 2960 switch, but I can not.
I am trying to configure the interface using the following commands: [code] similar result is obtained while trying to configure a auth-fail vlan. the full configuration file is attached.
In our new Head office we have to set up a Network connectivity.Total our office 4 floors.In each floor we kept three cisco 2950 switch.We have L3 switch(cisco 3560) to connect the all the other switch.In our office total 5 departments.we have to create VLan for each departments in the switch.
We want to all user to communicate to each other.We have WAN connectivity in the router(cisco 2900) to connect the other office.First i want know how to physically connect all the swiches and finally with the L3 switch.How to configure the VLAN in both L2 and L3 switch.In our other client office one router to connect the both office.In the router how to configure and which protocol to use to communication.
Ip address:10.10.40.0/22
WAN IP :192.168.214.65/30
I have a 3560 switch with 1 VLAN (VLAN 10) where I need to make ports:
1-10 as isolated (can't contact each other)
11-20 as community (need to contact each other like a normal VLAN)
23 as promiscuous (server that ports 1-20 need to get to)
24 as promiscuous (WAN router where ports 1-20 need to get to and the remote servers).
[Code]...
is it possible with LMS 4.0 and VLAN Port Assignment also to configure auxiliary vlans?
1. I selected Configuration > Workflows > VLAN > Configure Port Assignment.
2. Selected my device (a test switch WS-C3560-8PC-S)
3. Clicked List Ports
All ports were listed, port Fa0/1 has only a native vlan, the ports Fa0/2 - 8 have native and voice vlans (auxiliary) configured manually.
So when I want to configure the voice vlan for Fa0/1 the voice vlan is set as the native one.
Is it only possible to configure the native vlans with the VLAN Port Assignment of LMS 4.0 ?
We have over 30 Cisco 3560 switches and over 10 VLANs on our network. In our example, VLAN 10 on switch IP 10.0.20.150 works fine and VLAN 10 on switch IP 10.0.20.24 doesn’t work. The below are both switches show vlan. url....I can’t tell what causes the problem and how to fix it. VLAN 10 on Switch 10.0.20 24 doesn’t work. [code]
View 8 Replies View RelatedI'm unable to login Switch.......getting following error...I have tried this commands on other 3560 that worked...when I enter user name & password re logging authentication failed error occurs .........This is remote site Switch.
[code]...
I am using 802.1x authentication with multi-domain ports; Phone and PC connected to phone. The phones are Nortel (Avaya) and the PCs are Dell/HP Laptops. All are configured for Certificate authentication and this works well. However we sometimes get some ports stuck in Guest mode. when a non certificated laptop connects to a phone port and fails authentication, the data port is placed in the Guest VLAN. However when the laptop disconnects the port isn't reset and remains in the guest state. When a subsequent good laptop connects and attempts to authenticate the switch ignores this and leaves the data port in the Guest VLAN. he switch is a 2960S with Version 12.2(58)SE2 IOS.
The port is configured as follows:
!
interface GigabitEthernet1/0/15
description DANS Port
switchport access vlan 1807
switchport mode access
switchport voice vlan 1855
priority-queue out
[code]....
I placed the AAA, dot1x, eap and auth debug on for all events and then connected a good laptop, the only debug message I got were as follows:
Mar 19 16:17:01.391 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_restrictive_vlan_open_auth:Multi-Host with Guest Vlan/Auth Fail Vlan or open aut
Mar 19 16:17:01.653 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_restrictive_vlan_open_auth:Multi-Host with Guest Vlan/Auth Fail Vlan or open aut
Mar 19 16:17:02.654 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_restrictive_vlan_open_auth:Multi-Host with Guest Vlan/Auth Fail Vlan or open aut
[code]....
I would have expected the auth function to have reacted to the EAP packets sent by the good client when it connected and performed eap authentication but it didn't, all it did was say the ports in Guest mode and left the laptop in this VLAN.
I was wondering if it is possible to do dynamic VLAN assignment on the Cisco Wireless Controller 5508 without using Cisco ACS but use Microsoft NPS server instead?
View 3 Replies View RelatedI have just upgraded our WLC from 4.0 to 7.0 (via 4.2). Before the upgrade we had our ACS returning a VLAN based on user group. This seemed to be working without an issue. Now that the WLC is on version 7 this is no longer working correctly. The ACS is returning a VLAN and passing the user but the client can not get an IP from the DHCP server configured.
Example configuration:
SSID-----VLAN
PN-CSC-----CSCVlan: Works
PN-Others------OthersVlan: Works
PN-Others-----CSCVlan: No DHCP
When users are trying to be allocated to a vlan that is different from the native one the DHCP fails however both WLANs are configured to point to the management interface so dont have any real connection to the vlan other than by name.
Have there been any changes I haven't seen in the way the dynamic vlan allocation works in version 7?
I'm having trouble getting the dynamic vlan assignment to work on my 1242AG Cisco Aironet APs. I've seen multiple cases with a similar setup and configuration where it works just fine. I've tried everything I can think of. IAS and AD is running on Windows Server 2003.Everything works fine except the vlan assignment. Wireless clients successfully authenticate through IAS and Active Directory, but instead of being switched to the appropriate vlan the client stays in whichever vlan/ssid it originally connected to.PEAP is the authentication method, using MS-CHAP v2. Naturally I have the attributes in the policy set appropriately,[code] I've attached the config for the AP, which shows that I have two vlans/SSIDs set to cipher, aes, network eap, wpa, etc. I noticed that if the Tunnel-Pvt-Group-ID attribute is set to a vlan id that doesn't exist on the AP then the AP makes an event log saying so.
View 16 Replies View RelatedDoes the WAP4410N support Dynamic VLAN assignment by means of 802.1x authentication?
The reason why I ask this; I am able to configure a SSID on a WAP4410N with WPA2-Enterprise, in combination with 802.1x PEAP network authentication. I can succesfully connect Windows, Windows RT, Windows Phone, iOS and Android devices. But.. I am unable to designate them to another VLAN based on access/connection policies. For example; I want mobile devices such as iPhone and Windows Phone to be assigned to a specific VLAN. The Wireless Access Point (authenticator) must be able to support that.
This is my setup:
Spplicants: Windows 8 / iPad / ...
Authenticator: WAP4410N
Authentication Server: Microsoft NPS (Network Policy Server)
I used 802.1x PEAP (Protected EAP) with password (domain user) authentication. In fact, the suplicants communicate with 802.1x to the authenticator. The authenticator communicates with RADIUS to the authentication server. NAP is not in between. It's just plain 802.1x authentication.
wether dynamic VLAN assignment is supported?
I am having the Cisco NAC enviroment (Software Version is 4.9.1) and OOB VG.
We are getting the below and attached Error while deploying on some machines.
"Invalid switch configuration-OOB Error:OOB client "mac/ip" not found."
Some users on same switches are working fine but some are not....
What would be the possibilities and any work around? other than keeping the port shudown for long time means that atleast 10 - 20 secs or more or a PC restart. Customer is not feeling comfortable with the current situation.
I have a SG300-28P switch. I just read in the Administration Guide that, when in Layer 3 mode, the switch doesn't support MAC-based VLAN or Dynamic VLAN Assignment.
So, in order to assign a client to a VLAN based on their MAC or based on the response of a RADIUS server, we have to disable layer 3 features. Without layer 3 switching, the switch is unable to act as a default gateway and forward packets between VLANs. As a result, the VLANs can't communicate in any way, or access the internet, unless a separate router is connected to every VLAN. Right? Doesn't this limitation significantly reduce the usefulness of the DVA feature?
I want to use RADIUS (of Secure ACS 5.3) to authenticate users within an ISP environment. Users log connect to a network using a point to point connection (L2) and then they are sending a RADIUS request to get IP adresses. Secure ACS is not quite easy to look through in that case.
View 3 Replies View Relatedmy admin user is still being assigned privilege level 1, as shown in AAA Protocol > TACACS+ Authentication Details report.The report seems to show that the user is getting the right shell profile (Selected Shell Profile: Net-Admin -- is the one I setup for this user's group with both Default Privilege and Maximum Privilege set to Static 15). But still not the right privilege (Privilege Level: 1).Also, I found this document via Google: [URL] The router configuration examples all show this "aaa authorization exec tacacs+|radius local" command, which my device does not have.So I am wondering if I am not reading the ACS report right, or the device actually was assigned the correct privilge but that does not work without the "aaa authorization exec" command in the configuration?
View 1 Replies View Relatedhow I can assign a static IP to a user in ACS 5.2. I am able to do it in ACS 4.2, but I don't see the same options under 5.2. General idea is that users authenticate from our VPN appliance via RADIUS, and upon authentication, their static IP is passed back to the VPN device. I can attach an arbitrary field to my local users by going to System Administration -> Configuration -> Dictionaries -> Identity -> Internal Users, but how do I get that IP address passed back when the user is authenticated via Radius?
View 1 Replies View RelatedI have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies View RelatedI have a problem, i would like todo MACSEC betwwen two switches cisco catalyst 3560-x but I know that for this operation i needed ACS server 5.1 is it possible to encryp dataflow without ACS server and if you have the configuration
View 7 Replies View RelatedI have two ACS v 5.2 (primary and secundary) and some users are in the internal stor and the others are in the AD.The local site topology is like this:
PC - AP - WLC - ACS - AD
Authentication method is PEAP(EAP-MSCHAPv2) and all user have the certificate company installed. The OS in the client users is Windows 7.Users was working fine but some users reports intranet disconnections. I see in the ACS log many "22056 Subject not found in the applicable identity store(s)." and "24415 User authentication against Active Directory failed since user's account is locked out" alarms.I believed it was because user wasn´t in the AD data base, but some times the same user is authenticated successfull and other i see the "22056...." or "24415...." alarms.
I switched the role for ACS primary to works as secundary and we see the same alarms.
I have a 2 cisco switches that are at different sites one is a Cisco CAT4500 and other 3560. The connection between the switches is a layer 2 fibre link. CAT4500 and 3560 both have VLAN interface ip addresses in order for me to connect to the switches.
I have PC A connected to CAT4500 and PC B connecting to 3560. All these devices are the same VLAN and in the same subnet. I do have trunk links all the way though allowing this vlan as we run vlans. From PC A, I can ping CAT4500, 3560 and even PC B. This tells me everything is fine regarding Layer 2 & 3.
As soon as I move PC B and connect it to the other switch CAT4500 or move the other PC vice versa (this happens in both directions). Both switches learn that the mac address has moved locations and updates its mac address table accordingly. So when I do a show mac address table and show arp, everything has learned and moved fine. However when I try to ping any other device from PC B I cannot. So the 3560 switch PC B was originally connected to, I can no longer ping, the switch cannot see the pc also. It is as if PC B has not learned anything from the switch and cannot respond or reply to any icmp. I have tried this with different end devices, same thing. I am now thinking it has something to do with the switch.
I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
I am primarely enquiring whether the setup I have explained below is actually possible, and if so then how I can set this up. I know it isn't the easiest configuration and I need to set this up without purchasing any more equipment if at all possible.I have a Cisco SG 300-28 setup with three VLAN's. [code] Default Gateway is 192.168.10.1 (Netgear Router)I have a Wireless network setup (Netgear WMS and 2 WAP's) configured with the TWO VLAN's (1 and 3). These go into ports on the Cisco SG 300-28 which are tagged on both VLAN's. The Business wireless worked fine but the guest network didn't reout out to the internet.After some troubleshooting I realised the reason the guest wasn't working was because there was no route back from the internet to the router.
The router I have isn't really ideal, it is a Netgear DGN2200, but I managed to create a static route to 192.168.30.1 with a metric of 2, with 192,168,10.254 being the hop. Success, the connection worked, the only problem is that now my guest network can see my business network because the business network is using the static route on my router to route back over to the guest network (due to the limitations of this device I can't do anything about that)Guest network can connect to Business VLAN via switch. I am assuming this is because the router is on the Business VLAN and the default gateway is the router. As they are on the same network the Guest network can inevetably see the business server and network.The Business network can get back to the Guest network via the router using my static route I created. The static route is really basic and I can't create a firewall rule on the router to prevent the Business network speaking to guest network because it only has a LAN - WAN firewall and this connection is LAN - LAN.
What I need is...to somehow stop any traffic from the 192.168.30.0 network routing to anything on the 192.168.10.0 network, appart from the router on 192.168.10.1.Is this possible? I have this setup on a number of different site, the only difference is I have a CIsco Security Router on these with the VLAN's configured so I don't have this problem. Because I have a rather limited Netgear DGN2200 I am unable to setup the VLAN's correctly and as such I need to see if I can do this on the switch in any way.