Cisco Wireless :: VLAN Assignment Without ACS On 5508
Apr 8, 2013I was wondering if it is possible to do dynamic VLAN assignment on the Cisco Wireless Controller 5508 without using Cisco ACS but use Microsoft NPS server instead?
View 3 Replies
ADVERTISEMENT
Cisco Wireless :: WAP4410N 802.1x Dynamic VLAN Assignment?
Nov 27, 2012Does the WAP4410N support Dynamic VLAN assignment by means of 802.1x authentication?
The reason why I ask this; I am able to configure a SSID on a WAP4410N with WPA2-Enterprise, in combination with 802.1x PEAP network authentication. I can succesfully connect Windows, Windows RT, Windows Phone, iOS and Android devices. But.. I am unable to designate them to another VLAN based on access/connection policies. For example; I want mobile devices such as iPhone and Windows Phone to be assigned to a specific VLAN. The Wireless Access Point (authenticator) must be able to support that.
This is my setup:
Spplicants: Windows 8 / iPad / ...
Authenticator: WAP4410N
Authentication Server: Microsoft NPS (Network Policy Server)
I used 802.1x PEAP (Protected EAP) with password (domain user) authentication. In fact, the suplicants communicate with 802.1x to the authenticator. The authenticator communicates with RADIUS to the authentication server. NAP is not in between. It's just plain 802.1x authentication.
wether dynamic VLAN assignment is supported?
Cisco AAA/Identity/Nac :: ISE - WLC 7.2 VLAN Assignment?
Sep 10, 2012The Wireless_Employees authorization profile,assign vlan 666 for wireless employees.ISE is passing VLAN 666 to the WLC - see attachement Radius Auth-VLAN666.jpg then I look on the WLC at a wireless employee who has successuflly connected to the network, WLC is still placing him in the pre-configured VLAN 7.
1. can VLAN be pushed from ISE to the WLC (code 7.2.103) for specific user session?
Cisco :: WLC 4.0 - Dynamic VLAN Assignment And DHCP
Jan 16, 2011I have just upgraded our WLC from 4.0 to 7.0 (via 4.2). Before the upgrade we had our ACS returning a VLAN based on user group. This seemed to be working without an issue. Now that the WLC is on version 7 this is no longer working correctly. The ACS is returning a VLAN and passing the user but the client can not get an IP from the DHCP server configured.
Example configuration:
SSID-----VLAN
PN-CSC-----CSCVlan: Works
PN-Others------OthersVlan: Works
PN-Others-----CSCVlan: No DHCP
When users are trying to be allocated to a vlan that is different from the native one the DHCP fails however both WLANs are configured to point to the management interface so dont have any real connection to the vlan other than by name.
Have there been any changes I haven't seen in the way the dynamic vlan allocation works in version 7?
Cisco :: Dynamic Vlan Assignment With 1242AG And IAS Not Working
Dec 13, 2012I'm having trouble getting the dynamic vlan assignment to work on my 1242AG Cisco Aironet APs. I've seen multiple cases with a similar setup and configuration where it works just fine. I've tried everything I can think of. IAS and AD is running on Windows Server 2003.Everything works fine except the vlan assignment. Wireless clients successfully authenticate through IAS and Active Directory, but instead of being switched to the appropriate vlan the client stays in whichever vlan/ssid it originally connected to.PEAP is the authentication method, using MS-CHAP v2. Naturally I have the attributes in the policy set appropriately,[code] I've attached the config for the AP, which shows that I have two vlans/SSIDs set to cipher, aes, network eap, wpa, etc. I noticed that if the Tunnel-Pvt-Group-ID attribute is set to a vlan id that doesn't exist on the AP then the AP makes an event log saying so.
View 16 Replies View RelatedCisco AAA/Identity/Nac :: Guest Vlan - Assignment Error On 3560 Switch?
May 18, 2013I am configuring 802.1X in a 3560 Switch, my Radius server is a Microsoft IAS, when I connect a station of a guest user, the guest-vlan is not assigned in the port, and I have these logs:
May 8 21:23:02: dot1x-ev:Received an EAP Timeout on FastEthernet0/8 for mac 0000.0000.0000
May 8 21:23:02: dot1x-ev:dot1x_guest_vlan_applicable: Guest VLAN not
[Code].....
Cisco AAA/Identity/Nac :: ACS4.1 - Radius Dynamic VLAN Assignment Not Working?
Jan 28, 2013When the users connect their laptop they are getting a authentication prompt but the switch is not changing the VLANs on the port after successful authentication.Below are the logs on the switch
Jan 28 2013 17:21:32.417 CST: RADIUS: Framed-MTU [12] 6 1500
Jan 28 2013 17:21:32.417 CST: RADIUS: Called-Station-Id [30] 19 "E4-D3-F1-0B-C6-0A"
Jan 28 2013 17:21:32.417 CST: RADIUS: Calling-Station-Id [31] 19 "84-8F-69-A8-BD-1D"
Jan 28 2013 17:21:32.417 CST: RADIUS: EAP-Message [79] 45
[code]....
Cisco Switches :: Dynamic VLAN Assignment And Layer 3 Switching On 300 Series?
Jul 11, 2012I have a SG300-28P switch. I just read in the Administration Guide that, when in Layer 3 mode, the switch doesn't support MAC-based VLAN or Dynamic VLAN Assignment.
So, in order to assign a client to a VLAN based on their MAC or based on the response of a RADIUS server, we have to disable layer 3 features. Without layer 3 switching, the switch is unable to act as a default gateway and forward packets between VLANs. As a result, the VLANs can't communicate in any way, or access the internet, unless a separate router is connected to every VLAN. Right? Doesn't this limitation significantly reduce the usefulness of the DVA feature?
Cisco AAA/Identity/Nac :: 3750x / Dynamic VLAN Assignment For Wired Campus Network
Nov 23, 2012I`m working on Dynamic Vlan Assigmenton the basis of end user authenticatedwhoc are part of specific AD Group in c ampus enviorment.Objective: Need to assign the vlan on switch port on the basis of authenticated users OU Group in Active Directory. Eg: There are 2 OU groups in AD, Sales and Administration. Authenticated user in Sales group should get Vlan 10 and user in Admininstration Group shoudl get Vlan 20.
Components:
Cisco 3750x/Cisco 4500
ACS Version 5.2
Microsoft AD
Cisco AAA/Identity/Nac :: Use 802.1x To Authenticate Clients On Network With Dynamic VLAN Assignment From RADIUS?
Apr 11, 2013I'm trying to use 802.1x to authenticate clients on my network with dynamic VLAN assignment from RADIUS. We have IP-Phones(powered by PoE) that only supports EAP-MD5, and we would rather use MAB(it also uses LLDP-MED for some settings) to authenticate the phones using the MAC-range from the phones vendor. The following scenario works perfect:Connect the phone and let it boot up(takes a while) and authenticate with MAB.Connect a computer in the phones data-port and let it authenticate with 802.1x(or fail and reach guest-vlan) However, the following scenario doesn't work:The computer is already connected to the phoneThe phone is then connected to the switch What happends now is that the computer is authenticated using 802.1x before the phone boots up and get's authenticated with MAB. When the phone is ready, it's authenticated with MAB and everything works. However, after a short period(let's say a minute), using `debug authentication all`, we see a "NEW LL MAC: phones mac" message(which is weird since the mac has already been MAB-authenticated), and then we are unable to contact the phone using ping. When I check `show mac address-table` it has now moved the mac from `Port Gi 0/12` to `Port Drop`. However, if I check `show mab interface Gi 0/12` or `show authentication sessions` it lists the phones-mac as `mab auth sucess `.why the first scenario works, and not the second?
The switch is a 3560E PoE 24p with IOS 12.2.58SE2. Sample of the switch-config: network-policy profile 1voice vlan 90!interface GigabitEthernet0/12switchport mode accessnetwork-policy 1authentication control-direction inauthentication event fail retry 1 action authorize vlan 60authentication event server dead action authorize vlan 60authentication event no-response action authorize vlan 60authentication event server alive action reinitializeauthentication host-mode multi-domainauthentication order mab dot1xauthentication priority mab dot1xauthentication port-control autoauthentication periodicauthentication violation replacemabdot1x pae authenticatordot1x timeout tx-period 5dot1x max-reauth-req 1spanning-tree portfast!Btw, when we tried authenticating the phones using 802.1x too (EAP-MD5), there are NO problems in any of the scenarios. However, we want to use MAB instead of 802.1x to avoid the requirement of configuring the phones with a username and password. The RADIUS response was the same when using 802.1x as it is with MAB for the phones (including device-traffic-class=voice AV-pair).
Cisco Wireless :: 5508 WLC In HA Over L2 VLAN
Nov 13, 2012I am very interested in the new 7.3 feature HA.Also I can read that it is recommended to connect the two WLCs directly. How to use a L2-VLAN between them, in fact to bridge a distance between two data centres?
View 3 Replies View RelatedCisco Wireless :: 5508 / AP On Different Vlan Than Controller?
Sep 30, 2011I have a 5508 controller at our headquarters and am installing some 3502 AP's at a remote branch. Unfortunatly, the remote branch has a different Vlan setup for some reason and the vlan that is used for the WLC (90) is designated for telephony at this branch. Can I put the AP's on a different VLAN (10) without having any issues? I will still use DHCP option 43 to point them back to the controller. Below are the configs for the WLC interfaces and what I am proposing for the AP interfaces:
WLC Config
interface GigabitEthernet1/1/38
description WLC01
switchport
switchport trunk encapsulation dot1q
switchport trunk native vlan 90
switchport trunk allowed vlan 1,10,50,90,91,390,410-413,610-613,800,810,811
switchport mode trunk
[code]......
Cisco Wireless :: WLC 5508 Multicast Between SSID's And Vlan's
Dec 12, 2012is it possible to multicast between 2 different SSID's that are associated to 2 different VLAN's?
View 2 Replies View RelatedCisco Wireless :: WLC 5508 Request Received On Wrong Vlan
May 31, 2012We have two WLC's 5508. Following are its interfaces & details:mgmt 10.49.5.251 on wlc1 & .252 on wlc2 access p 10.49.6.251 on wlc1 & .252 on wlc2 there is no AP manager interface seen on both wlc's nor configured. both wlc1 & wlc2 are connected each to two switch ports, configured as normal trunk link each.LAG is enabled on both WLC's.
View 2 Replies View RelatedCisco Wireless :: H-Reap Vlan Mapping Groups On WLC 5508
Feb 29, 2012Im configuring a WLC 5508 ( version 7 ) with h-reap local switching.All is working , yet i wonder if the vlan mapping can be done better.Currently i need to go into each Lightweight Access point , enable h-reap, then set the native vlan , with the final step to map the vlan. This needs to be done for each AP. In an environment of 100's of APs i would take forever. ( i thought one of the main points of the WLC is centralized management).
View 1 Replies View RelatedCisco Wireless :: 5508 To Use Same VLAN And WLANs For Wired Guests
Jan 2, 2013We created a VLAN interface and a WLAN on the wireless controller (5508) and using it for Guest Wireless (Web auth), can we use the same VLAN and WLAN s for Wired Guests also?
View 5 Replies View RelatedCisco Wireless :: New 5508 DHCP For Management VLAN Not Working?
Sep 25, 2012I have a new 5508 that I am setting up. My first one from scratch.
Interfaces:
managment -> 10.10.10.10 ->dhcp 10.10.10.1
voice -> 10.10.7.1 ->dhcp 10.10.10.1
guest -> 192.168.1.2 ->dhcp 192.168.1.2
Local DHCP (via the 5508) is for the guest network while the management and voice use the Windows DHCP server.
My problem, Voice and guest work fine. I have two SSID's (one 802.1X and the other PSK) that use the management interface that will not get an IP. I have enabled dhcp proxy from the cli on the controller. I tried with the management VLAN tagged and untagged.
Cisco Wireless :: WLC 5508 / Cannot Create Interface As Same Vlan Id And Subnet
Aug 12, 2012I have got a wireless project with WLC main office and have 10 sites where ap's are there and ap's getting registerd .we need 4 ssid in all branches same .
ssid guest
ssid scanner
ssid user
vlan 600 main office for scanner 192.168.1.0
in branch
vlan 600 for scanner but ip is 172.16.1.0
and bgp is running . And customer is asking me not to edit the ip range or vlan or create new vlan . but in wlc am not able to create branch network 172.16.1.0 range interface and vlan 600 as vlan 600 i already created for scanner main office 192.168.1.0 So is there a way to do that .
Temprarly one site i did like created vlan 610 in branch no ip . And in main office interface vlan 610 given another ip range . and i created interface in wlc . from branch i can connect the ssid and getting ip . But they dont want to create any aditional vlan or another network . Customer dont have a smartnet contract . They recently baught 2 wlc 5508 and 40 ap 1142.
Cisco Wireless :: WLC 5508 / Guest VLAN Unable To Get DHCP IP Address From Anchor Controller
Feb 23, 2012In our test set up, we have two WLC 5508 Controllers connected via Checkpoint UTM-1 firewall Inside and DMZ Interfaces. Both the WLC controllers are connected to the firewall via Cisco 3750 switch. On the Local (Inside) Controller, guest SSID is enabled and attached to the wireless management Interface. On the remote anchor controller, guest SSID is enabled and attached to the Management Interface as well. The following configs are replicated on both the Controllers.
SSID Name - guest
Interface - Management ( VLAN 10 on Local and VLAN 20 on remote) -
Mobility Group: Same configs at both ends
SSID Anchor : Anchor SSID on local and local SSID on Anchor.
AP: CAPWAP 3502 Management Subnet
[code]....
Is there any thing missing in the wireless configs and or the firewall rules as i could not see DHCP request back from the Anchor Controller. Also, after DHCP is obtained, the web authentication request will be redirected to an Amigopod device for authentication. In this case is the redirect URL congiguration to be performed only on the Anchor Controller or is this to be replicated on both the Local and Anchor Controllers.
Cisco Wireless :: 5508 / H-REAP LWAPs Losing VLAN Mapping When Fail To Secondary WLCs
May 2, 2011I have three 5508 WLCs, running code 7.0.98.0 supporting 100+ LWAPs in H-REAP mode. The LWAPs are servicing 2-3 WLANs each. Some are using central authentication and local switching, some are configured for central authentication and central switching. When the LWAPs fail from one WLC to another WLC, the LWAP's lose all of their VLAN mappings and pick up the VLAN of the management interface on the new WLC.
All WLANs are configured to use the management interface on the WLC and the VLAN mappings are configured per LWAP on the H-REAP properties tab. The WLAN ID numbers and all the WLAN settings are the same across all 3 WLC's. I have created AP groups on all 3 WLC's and the AP group config matches across the 3 WLCs.
I can get the LWAPs to keep their VLAN mapping by creating an interface on the WLC with the VLAN ID of the locally switched/remote site VLAN and then setting the interface for the WLAN to the new interface. However, then the WLAN doesn't work, because the centrally located WLC doesn't have the remote site VLAN. It also seems to keep the VLAN mapping if I create the locally switched/remote site VLAN interface on the WLC , and point the WLAN to the management interface. This shouldn't be a necessary step though... In H-REAP with local switching, the LWAPs aren't using the interface on the WLC.
I found a note in the 7.0 WLC config guide that explains why the VLANs are picking up the management interface VLAN, but that same note says the VLAN mappings can be changed per LWAP/WLAN!
From config guide: For hybrid-REAP access points, the interface mapping at the controller for WLANs that is configured for H-REAP Local Switching is inherited at the access point as the default VLAN tagging. This mapping can be easily changed per SSID, per hybrid-REAP access point
Using H-REAP and been able to get the LWAPs to keep the VLAN mapping when failing from one WLC to another?
Cisco Wireless :: AP Power Level Assignment 1252
Sep 1, 2011We are using WiSM WLCs and WCS to control a variety of 1131,1142 and 1252 APs utilising AP groups.
I've noticed on WCS that the power of certain APs is at a low setting, even though the APs surrounding them are also at a low setting. This is causing some gaps to appear on the heatmaps. I was under the impression that the WLCs would regulate the AP power to compensate for any gaps. Currently the global TX power level assignment method algorithm is set to automatic every 600 sec.
Now, obviously I could change this to fixed (not ideal as I may not want all my APs to run at max power all the time) or to on demand (also not ideal due to the increased admin).
Is there a way I can verify that the automatic power levels are adjusting as they should? Why are there gaps appearing in my heatmaps?
*NB It's not just the gaps on the heatmaps, I'm getting reports of dropping wireless signals from users hence me looking at the heatmaps and they just happen to correspond.
WLC version 6.0.199.4
WCS version 7.0.172.0
Cisco :: 5508 OpenDNS On Public Vlan
Jan 8, 2012I have a 5508 WLC that for whatever reason cant take any DNS settings, but I still need to get some filtering on the public hotspot side of my wireless network. Can I put the DNS settings on the router that the circuit terminates on? This is the same router that the public vlan is defined on, I'm just not sure if I can put DNS settings in place for just one vlan, and how that'd work.
View 3 Replies View RelatedCisco Wireless :: Adjusting Maximum Power Level Assignment Value With AIR-CAP35021
May 1, 2012I have a deployment of AIR-CAP35021 APs. They are in 2 buildings with multiple floors. They are installed in a row down the hallways. I want to increase the power levels by using the controller and not configuring the APs individually. I have set the TPC value to -50 but I still do not reach the outer walls of the floors in some areas. I need to know what to set the Max Power Level Assignment or Min Power Level Assignment to to get the APs to power up some more. If the MAX value is 30 and the default is 30 then how to adjust that value?
View 5 Replies View RelatedCisco :: WLC 5508 AP Group - Clients Using Wrong VLAN
Feb 14, 2011I have a network setup as live-ssid. It is using the Interface for VLAN 14. All APs under the default-group AP Group obviously allows clients to DHCP an address from VLAN 14. This is working fine.
I created a new AP Group called 3rd Floor. This has the live-ssid setup, but instead of using the Interface for VLAN 14 it is setup for the Interface for VLAN 50. I have all the APs on this floor moved to the 3rd Floor AP Group.
The problem is that 95% of the clients on 3rd Floor are still picking up DHCP addresses from VLAN 14. I checked and all the clients are connected to the APs on the 3rd Floor. Only 4 Clients are getting an address from VLAN 50.
I'm not sure if something is configured wrong or not since some devices pick up the new VLAN and the rest don't. I've manually reboot the APs on the 3rd floor to see if that would fix it.
Cisco :: Requirements For VLAN Select Feature In 5508 WLC?
Jan 8, 2013We implemented WLC 5508 software version 7.3, with 8 Aironet devices, most of them are AIR-LAP1131AG-E-K9, and two AIR-LAP1242AG-E-K9.I could really have benefits of VLAN select feature, but I noticed that it's not working like it should. Two interfaces are in Interface group, but from 45 clients only few of them has IP address from one subnet, others have from second sub.I see requirements for this to work is 32 MB of flash on LWAP devices..I only have 16 MB.. upgrade of flash on devices or something ?
View 12 Replies View RelatedCisco Switching/Routing :: VLAN Interface Quantity Of WLC 5508?
Apr 25, 2013How many VLAN Interface can be create on a WLC Interface, e.g. GigabitEthernet 1?
View 2 Replies View RelatedCisco Wireless :: 4402 - Setting Update Time For Auto Tx Power Level Assignment
Dec 1, 2011We have a WLC 4402 controlling 40+ LWAPs. Is there a way to keep Tx power level assignment dynamic, but set the time of day it does it? I'd like to minimize user impact. (Firmware v. is 7.0.116.0)
View 2 Replies View RelatedCisco :: 5508 VLAN Select - DHCP Leases On Each Scope For Same Client
Sep 11, 2011The 5508 is running code 7.0.116.0. I have created a group interface for 3 subnets and assigned the group to the WLAN. Clients are getting IP addresses in a round robin fashion. The issue or downside to this is if the lease has not expired before the next time the station connects to the WLAN it consumes an address on another subnet instead of grabbing the unexpired lease IP address on it's previous VLAN. It seems that the WLC determines the VLAN in the interface group before the DHCP request from the client in case the client already received a DHCP address that has not expired. This can be problematic since we have seen some iPhones requesting an address every 20 minutes thus consuming an address on every subnet in the interface group. Other than setting a lease time extremely low what can be done to address this?
View 1 Replies View RelatedCisco :: WLC 5508 - Physical Port Devoted For Specific VLAN / Function?
Apr 2, 2013We have currently a WLC 5508 using 8 ports bundled into an etherchannel.
We would like to remove one physical from this etherchannel and use it for providing an access to Internet only,
Is it possible to create an virtual interface on the WLC that points only on this port?
(we would like to have a physical separation for the Internet traffic only and encrypt the capwapp up to the WLC).
WNDR3700 IP Assignment?
Apr 1, 2012In the settings, there is a spot in which you can set the range of IPs to assign to connected computers and other devices. This particular option is available under the "LAN" options. What I am seeing is that the only IP that is assigned within the range is the one and only device hardwired to the router. Everything else is being assigned IP addresses outside of the range. Am I missing something? I was under the assumption that any IP addresses assigned dynamically would be within the range whether they were wired or wireless
View 10 Replies View RelatedCisco VPN :: ASA 8.2 - ACS 5.2 With Dynamic VPN IP Pool Assignment?
Aug 7, 2011I have Remote Access VPN users (IPsec) who are terminated on Cisco ASA 5520 (v8.2). For those users, AAA is done on the ACS. Group-policies and tunnel groups are defined on ASA. Initialy I had all VPN users defined on ASA and group policies were associated with each user. Each group policy had it’s own IP pool for users. Now, I moved users to ACS. How can I associate group policy, defined on ASA, with users group defined on ACS? Is it possible that ACS send to ASA information about IP pool for different group policy? Users will use ONE vpn profile BUT based on the Active Directory group they belong to they obtain a different IP address for each group.Can it be done ? ACS version is 5.2.
View 1 Replies View RelatedCisco :: ASA Dhcpd Server Assignment Based On Mac
Sep 24, 2011is it possible to use the asa dhcp server function to assign based on mac address (yet)? I have read numerous places that it was not possible (as of 8.2) at least, but I am workin in 8.4. I should have mentioned that I've already tried commands (asa 5510 btw)
View 4 Replies View RelatedCisco :: Fictional Network Design Assignment
Mar 5, 2013I have gotten the assignment of constructing a fictional network for my school.. and i cannot quite agree with myself upon which equipment i should choose.. its supposed to be all cisco. i need to supply 5000 users all in all, but only 300 on this site. i need to know which connections would be the most reasonable to use and of course which routers "if any" and switches i need.. (+ additional modules if needed) i have tried to make a visio representation, but i just think something is way off.
View 6 Replies View Related