Cisco AAA/Identity/Nac :: ACS4.1 - Radius Dynamic VLAN Assignment Not Working?
Jan 28, 2013
When the users connect their laptop they are getting a authentication prompt but the switch is not changing the VLANs on the port after successful authentication.Below are the logs on the switch
Jan 28 2013 17:21:32.417 CST: RADIUS: Framed-MTU [12] 6 1500
Jan 28 2013 17:21:32.417 CST: RADIUS: Called-Station-Id [30] 19 "E4-D3-F1-0B-C6-0A"
Jan 28 2013 17:21:32.417 CST: RADIUS: Calling-Station-Id [31] 19 "84-8F-69-A8-BD-1D"
Jan 28 2013 17:21:32.417 CST: RADIUS: EAP-Message [79] 45
[code]....
View 1 Replies
ADVERTISEMENT
Apr 11, 2013
I'm trying to use 802.1x to authenticate clients on my network with dynamic VLAN assignment from RADIUS. We have IP-Phones(powered by PoE) that only supports EAP-MD5, and we would rather use MAB(it also uses LLDP-MED for some settings) to authenticate the phones using the MAC-range from the phones vendor. The following scenario works perfect:Connect the phone and let it boot up(takes a while) and authenticate with MAB.Connect a computer in the phones data-port and let it authenticate with 802.1x(or fail and reach guest-vlan) However, the following scenario doesn't work:The computer is already connected to the phoneThe phone is then connected to the switch What happends now is that the computer is authenticated using 802.1x before the phone boots up and get's authenticated with MAB. When the phone is ready, it's authenticated with MAB and everything works. However, after a short period(let's say a minute), using `debug authentication all`, we see a "NEW LL MAC: phones mac" message(which is weird since the mac has already been MAB-authenticated), and then we are unable to contact the phone using ping. When I check `show mac address-table` it has now moved the mac from `Port Gi 0/12` to `Port Drop`. However, if I check `show mab interface Gi 0/12` or `show authentication sessions` it lists the phones-mac as `mab auth sucess `.why the first scenario works, and not the second?
The switch is a 3560E PoE 24p with IOS 12.2.58SE2. Sample of the switch-config: network-policy profile 1voice vlan 90!interface GigabitEthernet0/12switchport mode accessnetwork-policy 1authentication control-direction inauthentication event fail retry 1 action authorize vlan 60authentication event server dead action authorize vlan 60authentication event no-response action authorize vlan 60authentication event server alive action reinitializeauthentication host-mode multi-domainauthentication order mab dot1xauthentication priority mab dot1xauthentication port-control autoauthentication periodicauthentication violation replacemabdot1x pae authenticatordot1x timeout tx-period 5dot1x max-reauth-req 1spanning-tree portfast!Btw, when we tried authenticating the phones using 802.1x too (EAP-MD5), there are NO problems in any of the scenarios. However, we want to use MAB instead of 802.1x to avoid the requirement of configuring the phones with a username and password. The RADIUS response was the same when using 802.1x as it is with MAB for the phones (including device-traffic-class=voice AV-pair).
View 2 Replies
View Related
Dec 13, 2012
I'm having trouble getting the dynamic vlan assignment to work on my 1242AG Cisco Aironet APs. I've seen multiple cases with a similar setup and configuration where it works just fine. I've tried everything I can think of. IAS and AD is running on Windows Server 2003.Everything works fine except the vlan assignment. Wireless clients successfully authenticate through IAS and Active Directory, but instead of being switched to the appropriate vlan the client stays in whichever vlan/ssid it originally connected to.PEAP is the authentication method, using MS-CHAP v2. Naturally I have the attributes in the policy set appropriately,[code] I've attached the config for the AP, which shows that I have two vlans/SSIDs set to cipher, aes, network eap, wpa, etc. I noticed that if the Tunnel-Pvt-Group-ID attribute is set to a vlan id that doesn't exist on the AP then the AP makes an event log saying so.
View 16 Replies
View Related
Nov 23, 2012
I`m working on Dynamic Vlan Assigmenton the basis of end user authenticatedwhoc are part of specific AD Group in c ampus enviorment.Objective: Need to assign the vlan on switch port on the basis of authenticated users OU Group in Active Directory. Eg: There are 2 OU groups in AD, Sales and Administration. Authenticated user in Sales group should get Vlan 10 and user in Admininstration Group shoudl get Vlan 20.
Components:
Cisco 3750x/Cisco 4500
ACS Version 5.2
Microsoft AD
View 1 Replies
View Related
Jan 16, 2011
I have just upgraded our WLC from 4.0 to 7.0 (via 4.2). Before the upgrade we had our ACS returning a VLAN based on user group. This seemed to be working without an issue. Now that the WLC is on version 7 this is no longer working correctly. The ACS is returning a VLAN and passing the user but the client can not get an IP from the DHCP server configured.
Example configuration:
SSID-----VLAN
PN-CSC-----CSCVlan: Works
PN-Others------OthersVlan: Works
PN-Others-----CSCVlan: No DHCP
When users are trying to be allocated to a vlan that is different from the native one the DHCP fails however both WLANs are configured to point to the management interface so dont have any real connection to the vlan other than by name.
Have there been any changes I haven't seen in the way the dynamic vlan allocation works in version 7?
View 8 Replies
View Related
Nov 27, 2012
Does the WAP4410N support Dynamic VLAN assignment by means of 802.1x authentication?
The reason why I ask this; I am able to configure a SSID on a WAP4410N with WPA2-Enterprise, in combination with 802.1x PEAP network authentication. I can succesfully connect Windows, Windows RT, Windows Phone, iOS and Android devices. But.. I am unable to designate them to another VLAN based on access/connection policies. For example; I want mobile devices such as iPhone and Windows Phone to be assigned to a specific VLAN. The Wireless Access Point (authenticator) must be able to support that.
This is my setup:
Spplicants: Windows 8 / iPad / ...
Authenticator: WAP4410N
Authentication Server: Microsoft NPS (Network Policy Server)
I used 802.1x PEAP (Protected EAP) with password (domain user) authentication. In fact, the suplicants communicate with 802.1x to the authenticator. The authenticator communicates with RADIUS to the authentication server. NAP is not in between. It's just plain 802.1x authentication.
wether dynamic VLAN assignment is supported?
View 5 Replies
View Related
Jul 11, 2012
I have a SG300-28P switch. I just read in the Administration Guide that, when in Layer 3 mode, the switch doesn't support MAC-based VLAN or Dynamic VLAN Assignment.
So, in order to assign a client to a VLAN based on their MAC or based on the response of a RADIUS server, we have to disable layer 3 features. Without layer 3 switching, the switch is unable to act as a default gateway and forward packets between VLANs. As a result, the VLANs can't communicate in any way, or access the internet, unless a separate router is connected to every VLAN. Right? Doesn't this limitation significantly reduce the usefulness of the DVA feature?
View 2 Replies
View Related
Jan 13, 2013
I want to use RADIUS (of Secure ACS 5.3) to authenticate users within an ISP environment. Users log connect to a network using a point to point connection (L2) and then they are sending a RADIUS request to get IP adresses. Secure ACS is not quite easy to look through in that case.
View 3 Replies
View Related
Sep 10, 2012
The Wireless_Employees authorization profile,assign vlan 666 for wireless employees.ISE is passing VLAN 666 to the WLC - see attachement Radius Auth-VLAN666.jpg then I look on the WLC at a wireless employee who has successuflly connected to the network, WLC is still placing him in the pre-configured VLAN 7.
1. can VLAN be pushed from ISE to the WLC (code 7.2.103) for specific user session?
View 3 Replies
View Related
May 18, 2013
I am configuring 802.1X in a 3560 Switch, my Radius server is a Microsoft IAS, when I connect a station of a guest user, the guest-vlan is not assigned in the port, and I have these logs:
May 8 21:23:02: dot1x-ev:Received an EAP Timeout on FastEthernet0/8 for mac 0000.0000.0000
May 8 21:23:02: dot1x-ev:dot1x_guest_vlan_applicable: Guest VLAN not
[Code].....
View 7 Replies
View Related
Aug 21, 2012
I am using several SG300-28 Switches with firmware version 1.1.2.0.I have dynamic VLAN enabled. As RADIUS server I am using free radius 2.1.12.Authentication is only based on the MAC address. (I configured that on the switches)On the switches I created three VLANs. VLAN100 for the authenticated clients, VLAN200 for Management interface and VLAN300 as Guest VLAN. After a wrong authentication the clients should be put into this Guest VLAN immediately (I configured this on the switches). I am using Windows XP and Windows 7 clients in my network. I did not configure any EAP settings because I just wnat to use the MAC address.
In most cases the dynamic VLAN assignment and authentication is working fine. The switch log says that the client is authenticated and the same I can see on free radius log. But in some (rare) cases the client is rejected. The CISCO log says "MAC aa:bb:cc:dd:ee:ff was rejected on port ge17" but when I look at the free radius log then this MAC address was successfully authorized.
The problem is that the client gets an IP address based on the Guest VLAN300 but after that the switch seems to "switch" the VLAN on the port and then the client is authenticated correctly on the right VLAN but the client does not request a new IP on the new VLAN. If I unplug and re-plug the LAN cable in most cases the client get the correct VLAN and the correct IP. This is happening randomly on nearly all my PCs.
Do I have to set some timers higher ? I don't think it is a problem between switch and RADIUS but a problem between communication of the host and the switch.
View 14 Replies
View Related
Aug 7, 2011
I have Remote Access VPN users (IPsec) who are terminated on Cisco ASA 5520 (v8.2). For those users, AAA is done on the ACS. Group-policies and tunnel groups are defined on ASA. Initialy I had all VPN users defined on ASA and group policies were associated with each user. Each group policy had it’s own IP pool for users. Now, I moved users to ACS. How can I associate group policy, defined on ASA, with users group defined on ACS? Is it possible that ACS send to ASA information about IP pool for different group policy? Users will use ONE vpn profile BUT based on the Active Directory group they belong to they obtain a different IP address for each group.Can it be done ? ACS version is 5.2.
View 1 Replies
View Related
Jan 6, 2013
Is it possible to disable DCA for a couple of APs and manually force the channels assignment ?
View 3 Replies
View Related
Aug 27, 2012
What are the VMware requirements to run ACS4.1.4? Im trying to use a VM this as the migration server. According to the cisco docs, it states that: "ACS 4.1 has been tested on the VMWare ESX server with the following configuration:
•VMWare ESX Server 3.0.0
•16 GB of RAM
•AMD Opteron Dual Core processor
•300 GB hard drive
•Four virtual machines
•Windows 2003 Standard Edition
•3 GB of RAM for the guest operating system"
I understand it will work as it "has been tested" with those specs, but the doc does not state the minimum requirements for the virtual machine. I dont want to use/find 300GB of space if I only need 20GB(as an example) to make it work.
View 2 Replies
View Related
Nov 14, 2012
We have configured following commands on switch to fallback to local Vlan if both radius server (policy persona's) is found dead. For test purpose we shutdown both servers (policy persona's) but fallback didn't work. We have 3750 switch running image 12.2(55)SE6 having following configuration.We do not know whether we configured switch in proper way or do we need to modify it. [code]
View 5 Replies
View Related
Sep 13, 2012
I have a cisco 3845 running 12.4(15)T10.
I can send a POD and disconnect my session. But when I try to send a COA, I always get back the same error. Here is the debug log:
*Sep 14 17:25:16.017: COA: 172.16.XX.XX request queued
*Sep 14 17:25:16.017: ++++++ CoA Attribute List ++++++
*Sep 14 17:25:16.017: 66F2DBEC 0 00000009 string-session-id(337) 8 0000007F
*Sep 14 17:25:16.017: 670B3394 0 00000009 sub-qos-policy-out(346) 11 POLICE-TEST
[code]....
View 10 Replies
View Related
Jun 6, 2011
I'm installing ACS4.2 in our lab domain and want to leverage the corporate domain for authentication. The one way trust is in place, but there is a facet that I'm not clear on in regards to the installation requirement.
I'd like to install ACS on a lab domain member server, but I'm not sure that will work. The installation docs seem to imply that a member server must be in the same domain as the authentication server, but its not very clear. if I want to use the one way trust to the Corporate Domain, am I required to install ACS on the domain controller of the Lab Domain?
View 3 Replies
View Related
Mar 21, 2011
Any relevant doc for ACS4.2 on 1113 platform to be integrated with Unix Directory service having LDAP10.2.0.0 version from Oracle or guidance available.
View 1 Replies
View Related
Apr 8, 2013
I was wondering if it is possible to do dynamic VLAN assignment on the Cisco Wireless Controller 5508 without using Cisco ACS but use Microsoft NPS server instead?
View 3 Replies
View Related
Dec 1, 2011
my admin user is still being assigned privilege level 1, as shown in AAA Protocol > TACACS+ Authentication Details report.The report seems to show that the user is getting the right shell profile (Selected Shell Profile: Net-Admin -- is the one I setup for this user's group with both Default Privilege and Maximum Privilege set to Static 15). But still not the right privilege (Privilege Level: 1).Also, I found this document via Google: [URL] The router configuration examples all show this "aaa authorization exec tacacs+|radius local" command, which my device does not have.So I am wondering if I am not reading the ACS report right, or the device actually was assigned the correct privilge but that does not work without the "aaa authorization exec" command in the configuration?
View 1 Replies
View Related
Jun 7, 2011
how I can assign a static IP to a user in ACS 5.2. I am able to do it in ACS 4.2, but I don't see the same options under 5.2. General idea is that users authenticate from our VPN appliance via RADIUS, and upon authentication, their static IP is passed back to the VPN device. I can attach an arbitrary field to my local users by going to System Administration -> Configuration -> Dictionaries -> Identity -> Internal Users, but how do I get that IP address passed back when the user is authenticated via Radius?
View 1 Replies
View Related
Jun 26, 2011
I have some 1130AG access point and I'd like to have :
- Multiple broadcasted SSIDs (because most of my clients are OSX and OSX doesn't deal with hidden SSID at all ! the clients have to enter the data each time which for WPA2 enterprise is really annoying)
- Dynamic VLAN assignement (so my clients don't have to know to which VLAN they belong and so I can easily change them from one to another).
As it turns out, it's apparently not supported to have both. But I can't understand WHY ? What exactly is the relation between those features ? What's the underlying technical constraint ?
I can understand the cipher suite must match between all the dynamic vlan because of the way wlan works, but for this, I really don't see what the problem is ... (Especially since I only have one of the SSID that needs dynamic assignement, the other is really the 'guest' one).
View 4 Replies
View Related
Oct 12, 2011
I'm wanting to setup a Virtual Office scenario. Everything is working fine except for 802.1x...I can get the 881 to authenticate things connected to it, but I don't have the options of guest-vlan or auth-fail vlan.Idea is if the users takes the router home and someone, either accidentally or on pupose, connects an unauthorized Laptop, they stay off the Corp network but can get to the internet still.I found this link on Cisco's site: [URL]That link shows them configuring a guest vlan right on the fa0-3 ports of an 881W. I dont have that option on mine. I can only configure 802.1x on the vlan interface. I have 802.1x working, for things that connect to vlan1, but I would like to have a "fallback" setup.
EZVPN_Remote(config-if)#int fa1
EZVPN_Remote(config-if)#dot
EZVPN_Remote(config-if)#dot1?
dot1q
EZVPN_Remote(config-if)#dot1
[code]....
View 1 Replies
View Related
Apr 22, 2013
I have enabled IP DHCP snooping on a 24 port 3560 switch (v small office) and let the database fill up, now I have added dynamic arp inspection on the single vlan and I amd getting these errors.
Apr 23 16:15:34: %SW_DAI-4-DHCP_SNOOPING_DENY: 1 Invalid ARPs (Req) on Fa0/5, vlan 1.([5835.d9b0.b9d1/172.30.5.2/0000.0000.0000/172.30.5.3/16:15:33 BST Tue Apr 23 2013])
Apr 23 16:15:39: %SW_DAI-4-DHCP_SNOOPING_DENY: 1 Invalid ARPs (Req) on Fa0/8, vlan 1.([0004.f2be.55e4/172.30.5.5/0000.0000.0000/172.30.5.8/16:15:39 BST Tue Apr 23 2013])
Apr 23 16:15:40: %SW_DAI-4-DHCP_SNOOPING_DENY: 1 Invalid ARPs (Req) on Fa0/8, vlan 1.([0004.f2be.55e4/172.30.5.5/0000.0000.0000/172.30.5.8/16:15:40 BST Tue Apr 23 2013])
[Code] .....
View 2 Replies
View Related
Apr 19, 2012
I've got a new 891 to replace an old 837 and I'm struggling to get the dynamic nat pool working.I've successfully configured the dialer etc for PPPoE and when I set up a static NAT translation between my PC and an external address then I can ping hosts on the internet e.g. ping 8.8.8.8 successfully. But when I remove the static translation and try and use the dynamic NAT pool then no NAT translations take place, and show ip nat translations only shows the other static entries.The relevant bits of the config are below and I've also attached a full (cleaned) config.
ip nat pool TestPool 81.2.123.226 81.2.123.226 netmask 255.255.255.248
ip nat inside source list 15 pool TestPool overload
! Can only access internet when static route is defined for my PC
! If I remove this line then it doesn't use the dymnamic pool TestPool
ip nat inside source static 172.16.0.11 81.2.123.226
[code]....
View 2 Replies
View Related
Oct 30, 2011
I am currently useing ACS 5.2 and have no problem using Tacacs+ with AD access.
But with Radius it seems I can only get the Local identity store to work, need to do something special to get Radius to work with active directory with Cisco ACS?
View 10 Replies
View Related
Apr 20, 2011
I am testing a ACS 5.2 in our lab environment, I am testing port security for policy based VLAN and ACL assignment. The problem I am having is with the 2960S switches; in my current setup it is working but it doesn't seem to me like it is the way that it should be working. I have a downloadable ACL in the ACS defined and associated to an Access policy and it is working correctly. The problem is, from what I understand, I have to assign a default ACL on the switchport? So what I have assigned on the switchport is ip access-group 10 in. The downloadable ACL from the ACS is also called 10. Do I really need to match the ACL on the switchport with the ACL name I have created in ACS? That doesn't seem like it's dynamic if that is the case? What is the ACL that I should apply to the switch port (if any) in order for the downloadable acls that I configure in the ACS to work no matter what port the user is patched into?
View 2 Replies
View Related
Dec 5, 2012
I am gettning warning messages in ISE saying
Cause:Dynamic Authorization Failed for Device: 0002SWC003 (switch)Details:Dynamic Authorization Failed
It is not only on that switch but on all switches I have configured. I am using 3560 IPBase 12.2(55)SE6. I have configured them according to Trustsec 2.1. My end devices are none-802.1x. I can't figure out what is causing this error.
The thing is that I have not experienced any problem. In Live Authentications there are some 'Unknown' and 'Profiled' devices hitting the DenyAccess rule, but other then that everying is beeing Authorized fine.
View 8 Replies
View Related
May 7, 2013
How often does ACS 4.1 purge dynamic users from it's user group after inactivity?
We're trying to disable access to certain resources via a NAR, and finding that some users are not in the ACS dynamic user database, despite that, at one point in the past, they have used it.
Am I correct in assuming that a user that has never authenticated via an ACS-controlled resource would not be in the database?
View 6 Replies
View Related
Nov 22, 2011
I have been trying to get our IPS (ASA-SSM-10 and 4260) to authenticate with Cisco Radius ACS 5.2 and they are not working. However, I was able to get them working with Microsoft Radius. Below is the logs from the IPS:
evStatus: eventId=1321566464942057375 vendor=Cisco originator: hostId: NACAIRVIDLAB1 appName: authentication appInstanceId: 350 time: 2011/11/23 17:50:38 2011/11/23 09:50:38 GMT-08:00 controlTransaction:
[Code].....
View 0 Replies
View Related
Dec 3, 2011
I need to configure RADIUS VSA configuration for a my alvarion device. Following are the attributes that need to be configured.
- Packet Data Flow ID (ID 1, integer16)
- Direction (ID 4, integer8)
- Transport Type (ID 6, integer8)
- UplinkQoSID (ID 7, integer8)
- DownlinkQoSID (ID 8, integer8)
[code]....
I was able to configure the first 6 attributes, how can I add the Sub - TLV's ClassifiedID, Priority, VLAN-ID and Classifier Direction which come under Classifier. Don't see any option for that in ACS 5.x
View 1 Replies
View Related
Jan 31, 2012
We have 2 ACS 4.2.1 servers in Windows 2003 with SP2 installed. We have updated the first ACS to the latest patches for Windows. After that we started having problems. CSRadius either stops by itself or when some time passes we get the following error in Failed attempts "Unknown error". When we restart the ACS services by the GUI, it resumes until the next time it stops.Do you happen to know if we have any bugs related to Windows patches?
View 3 Replies
View Related
Mar 25, 2013
I am trying to configure AAA authentication and authorization with Cisco 3725 (IOS 12.4(17)) for 802.1x and ACS 4.2 with VLAN assignment to my Windows XP client. (trying to assign VLAN 100 in my scenario).When user connects to the Router, it passes the authentication process (EAP-MD5). In my debug i see that Router recieves the Radius Attributes BUT does not apply anything!My running config:
Building configuration...
Current configuration : 1736 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[code]......
As a result the vlan-switch data based does not change.
View 3 Replies
View Related
