Cisco AAA/Identity/Nac :: ACS 5.2 Static IP Assignment For Local User
Jun 7, 2011
how I can assign a static IP to a user in ACS 5.2. I am able to do it in ACS 4.2, but I don't see the same options under 5.2. General idea is that users authenticate from our VPN appliance via RADIUS, and upon authentication, their static IP is passed back to the VPN device. I can attach an arbitrary field to my local users by going to System Administration -> Configuration -> Dictionaries -> Identity -> Internal Users, but how do I get that IP address passed back when the user is authenticated via Radius?
View 1 Replies
ADVERTISEMENT
Nov 12, 2012
I want to have a local user in ACS that is permitted to login to routers. I have TACACS with AD already working but cannot get a local user to work. I used to do this in ACS 4.x.I created a user in the internal identity store.I tried configuring a policy to allow this users TACACS authentication multiple ways to no avail. I cannot find a config example doc and cannot figure it out from the user guide as the documention is sorely lacking.
View 5 Replies
View Related
Feb 9, 2010
I know the way to configure the ASA to fallback to LOCAL authentication, if the Radius server is not available.
Now we would like to authenticate the local users, if the user is not found in the AD. Is this possible and how can I configure this with the new policies? I tested it with "dropping" when the user is not found in the AD, but then the Radius server will be marked as "dead" and the other AD users can't login for a given period. Maybe we can configure the dead time to 0, but this is not as nice it could be.
View 4 Replies
View Related
May 15, 2012
i am running NX-OS image n5000-uk9.5.1.3.N1.1.bin on the nexus 5020 platform.i have configured authorization with tacacs+ on ACS server version 5.2 with fall back to switch local database.a user test with priv 15 is craeted on ACS server, password test2 everything works fine, until i create the same username on the local database with privilege 0. ( it doesnt matter if the user in local database was created before user in ACS or after ) e.g.: username test password test1 role priv-0 (note passwords are different for users in both databases)
after i create the same user in local database with privilege 0,if i try to connect to the switch with this username test and password defined on ACS, i get only privilege 0 authorization, regardless, that ACS server is up and it should be primary way to authenticate and authorizate the user.
View 3 Replies
View Related
Apr 28, 2011
I am trying to configure an ASA 5505 running 8.3 to allow a priv 15 local user to be able to ssh into the device and be placed into priv 15 mode without having to execute the enable command and type the enable password.Right now when you log in as a priv 15 user you still have to execute the enable command and type the enable password to get to priv 15.
View 3 Replies
View Related
Oct 3, 2012
I'm a bit new to Cisco and i find this AAA a bit confusing..I've turend on AAA by:aaa new-model
Can I use this "default" list for WebVPN ? And what would be a different if i create new "sslvpn" list..Also when I'll be creating user for VPN remote access.. that user will also exist in local database and have access to router via SSH?Because the research I've done it doesn't seem you can group users in different "aaa groups" e.g. user admin belongs under "admin" aaa group which can do ssh to router, users for VPN can only do remote VPN access and not SSH and login into router.i saw ASA has some attribute for users called remote-user
•admin, in which users are allowed access to the configuration mode. This option also allows a user to connect via remote access.
•nas-prompt, in which users are allowed access to the EXEC mode.
•remote-access, in which users are allowed access to the network.
But i can't find this option in IOS on my 1900 Series ISR router.
View 1 Replies
View Related
Feb 12, 2012
Actually I have a lab with ACS 5.3 running with 802.1x, but when when the user is successfully authenticated, it's assigned and IP address from the DHCP server, is there a way to assign a static IP address depending of login username??
View 13 Replies
View Related
Sep 17, 2011
At first I use ACS 4.2 to create static ip address user for remote access VPN,It's easy,just configuration it at user set>Client IP Address Assignment>Assign static IP address,but when I use ACS 5.2 I dont't know how to do it.
I try to add IPv4 address attribute to user by read "ACS 5.2 user guide" ,it says this:
Step 1Add a static IP attribute to internal user attribute dictionary:
Step 2Select System Administration > Configuration > Dictionaries > Identity > Internal Users.
Step 3Click Create.
Step 4Add static IP attribute.
Step 5Select Users and Identity Stores > Internal Identity Stores > Users.
Step 6Click Create.
Step 7Edit the static IP attribute of the user.
I just do it,but it's not work.When I use EasyVPN client to connect ASA 5520,user could success to authentication but will not get the static IP address which I configure on Internal Users,so the tunnel set up failed.I try to Configure a IP pool on ASA for ACS users get IP address,and use EasyVPN client to connect ASA , everything is OK,user authenticate successed.but when I kill IP pool coufigurations and use the "add a static IP address to user "configurations,EzVPN are failed. how to use ACS 5.2 to create a static ip address user for remote access VPN?
View 7 Replies
View Related
Mar 29, 2011
I'm having a strange issue with a Cisco 3845 ISR router. I am setting up basic ACL and NAT but 2 issues occur. When using pat (overload) and a static nat assignment on the same subnet, the host with the static assignment has no wan connectivity except for icmp. The host is not reachable via the wan and the static public ip. Running show ip nat translations show the correct inside local and inside global addresses. The other issue is when applying an extended ACL to the outside or WAN interface coming in. No host on the inside has connectivity (icmp, tcp etc.) even to the gateway. I've cleared out all the ACL's as well as the ipsec tunnel settings and created only the nat overload and a single static assignment with the same results.I'm posting the running config below.
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[Code]...
View 13 Replies
View Related
Feb 8, 2011
I've got a network of several AIR-LAP-1242G LWAPP access points controlled by a 2112 WLC. I assign static IP addresses to each LWAPP, but every few weeks, a couple of them (at random) revert back to grabbing a DHCP-assigned dynamic address for themselves, despite the fact that they're supposedly solidy configured to have static IPs. What's going on here? Is this a bug in their firmware or the WLC's firmware? If I reboot the APs, then they come up with their static IPs, but after running some random number of days/weeks, will spontaneously change their own management IP addresses and grab a DHCP address for themselves.
The 1242G APs version numbers reported by the WLC's web GUI are:
"Software version" 5.2.193.0
"Boot version" 12.4.13.0
"IOS version" 12.4(18a)JA2
"Mini IOS version" 3.0.51.0
The 2112 WLC is running software version 5.2.193.0
View 2 Replies
View Related
Sep 10, 2012
The Wireless_Employees authorization profile,assign vlan 666 for wireless employees.ISE is passing VLAN 666 to the WLC - see attachement Radius Auth-VLAN666.jpg then I look on the WLC at a wireless employee who has successuflly connected to the network, WLC is still placing him in the pre-configured VLAN 7.
1. can VLAN be pushed from ISE to the WLC (code 7.2.103) for specific user session?
View 3 Replies
View Related
Oct 10, 2011
I want to create a local user in my Cisco ASA 5520 to allow the user to use the ASDM in Read-Only mode. I want the user to view the Dashboard only.
View 1 Replies
View Related
Jan 13, 2013
I want to use RADIUS (of Secure ACS 5.3) to authenticate users within an ISP environment. Users log connect to a network using a point to point connection (L2) and then they are sending a RADIUS request to get IP adresses. Secure ACS is not quite easy to look through in that case.
View 3 Replies
View Related
Dec 1, 2011
my admin user is still being assigned privilege level 1, as shown in AAA Protocol > TACACS+ Authentication Details report.The report seems to show that the user is getting the right shell profile (Selected Shell Profile: Net-Admin -- is the one I setup for this user's group with both Default Privilege and Maximum Privilege set to Static 15). But still not the right privilege (Privilege Level: 1).Also, I found this document via Google: [URL] The router configuration examples all show this "aaa authorization exec tacacs+|radius local" command, which my device does not have.So I am wondering if I am not reading the ACS report right, or the device actually was assigned the correct privilge but that does not work without the "aaa authorization exec" command in the configuration?
View 1 Replies
View Related
May 18, 2013
I am configuring 802.1X in a 3560 Switch, my Radius server is a Microsoft IAS, when I connect a station of a guest user, the guest-vlan is not assigned in the port, and I have these logs:
May 8 21:23:02: dot1x-ev:Received an EAP Timeout on FastEthernet0/8 for mac 0000.0000.0000
May 8 21:23:02: dot1x-ev:dot1x_guest_vlan_applicable: Guest VLAN not
[Code].....
View 7 Replies
View Related
Jan 28, 2013
When the users connect their laptop they are getting a authentication prompt but the switch is not changing the VLANs on the port after successful authentication.Below are the logs on the switch
Jan 28 2013 17:21:32.417 CST: RADIUS: Framed-MTU [12] 6 1500
Jan 28 2013 17:21:32.417 CST: RADIUS: Called-Station-Id [30] 19 "E4-D3-F1-0B-C6-0A"
Jan 28 2013 17:21:32.417 CST: RADIUS: Calling-Station-Id [31] 19 "84-8F-69-A8-BD-1D"
Jan 28 2013 17:21:32.417 CST: RADIUS: EAP-Message [79] 45
[code]....
View 1 Replies
View Related
Nov 23, 2012
I`m working on Dynamic Vlan Assigmenton the basis of end user authenticatedwhoc are part of specific AD Group in c ampus enviorment.Objective: Need to assign the vlan on switch port on the basis of authenticated users OU Group in Active Directory. Eg: There are 2 OU groups in AD, Sales and Administration. Authenticated user in Sales group should get Vlan 10 and user in Admininstration Group shoudl get Vlan 20.
Components:
Cisco 3750x/Cisco 4500
ACS Version 5.2
Microsoft AD
View 1 Replies
View Related
Apr 11, 2013
I'm trying to use 802.1x to authenticate clients on my network with dynamic VLAN assignment from RADIUS. We have IP-Phones(powered by PoE) that only supports EAP-MD5, and we would rather use MAB(it also uses LLDP-MED for some settings) to authenticate the phones using the MAC-range from the phones vendor. The following scenario works perfect:Connect the phone and let it boot up(takes a while) and authenticate with MAB.Connect a computer in the phones data-port and let it authenticate with 802.1x(or fail and reach guest-vlan) However, the following scenario doesn't work:The computer is already connected to the phoneThe phone is then connected to the switch What happends now is that the computer is authenticated using 802.1x before the phone boots up and get's authenticated with MAB. When the phone is ready, it's authenticated with MAB and everything works. However, after a short period(let's say a minute), using `debug authentication all`, we see a "NEW LL MAC: phones mac" message(which is weird since the mac has already been MAB-authenticated), and then we are unable to contact the phone using ping. When I check `show mac address-table` it has now moved the mac from `Port Gi 0/12` to `Port Drop`. However, if I check `show mab interface Gi 0/12` or `show authentication sessions` it lists the phones-mac as `mab auth sucess `.why the first scenario works, and not the second?
The switch is a 3560E PoE 24p with IOS 12.2.58SE2. Sample of the switch-config: network-policy profile 1voice vlan 90!interface GigabitEthernet0/12switchport mode accessnetwork-policy 1authentication control-direction inauthentication event fail retry 1 action authorize vlan 60authentication event server dead action authorize vlan 60authentication event no-response action authorize vlan 60authentication event server alive action reinitializeauthentication host-mode multi-domainauthentication order mab dot1xauthentication priority mab dot1xauthentication port-control autoauthentication periodicauthentication violation replacemabdot1x pae authenticatordot1x timeout tx-period 5dot1x max-reauth-req 1spanning-tree portfast!Btw, when we tried authenticating the phones using 802.1x too (EAP-MD5), there are NO problems in any of the scenarios. However, we want to use MAB instead of 802.1x to avoid the requirement of configuring the phones with a username and password. The RADIUS response was the same when using 802.1x as it is with MAB for the phones (including device-traffic-class=voice AV-pair).
View 2 Replies
View Related
Sep 22, 2011
We are running ACS 5.2 patch 6 and want to restrict access for users to be able to add devices to the system.For example, admin person in site A can only add devices into the site A group and cannot see/access other sites groups.
View 1 Replies
View Related
Nov 14, 2012
I want to limit a local user's access to some specific groups of devices. In Role Management Setup I can define which service they can access, but I want to restrict it to a specific device as well.
View 3 Replies
View Related
Apr 10, 2011
I am trying to configure ASA to assign same static ip address to certain user(User1) every time when he connect to network via AnyConnect client. We have Windows AD and use LDAP AAA server for authentication of VPN Remote Access users. I found in document "Cisco ASA 5500 Series Configuration Guide using the CLI, 8.2" in section "Configuring an External Server for Security Appliance User Authorization" explanation and configured ASA and User Properties in AD on exectly same way:First, I assigned static ip address in properties menu(dial in section) of User1 in Active Directory. Then I created ldap attribute map where I mapped msRADIUSFrameIPAddressattribute to IETF-Radius-Framed-IP-Address attribute. At the end I applied this ldap attribute map to AAA server group LDAP.
Although I set this up, whenever I connect using User1 credentials from AD I still get ip address from vpn pool instead static ip address that I configured. In output of debug ldap 255 command I found line "msRADIUSFramedIPAddress: value = -1062718956" but not any line that prove mapping above mentioned attributes.It seems like mapping is not working.All AnyConnect users get parameters from defined internal group policy on ASA,including addresses form pool,dns server etc. I want that User1 get static ip address and inherit all other parameters from group policy.
View 4 Replies
View Related
Nov 29, 2011
I want to assign static IPs to users that login to IPSec VPN using Group Authentication in ASA 8.2. The authentication through a Windows RADIUS server. Right now, they are connecting just fine and pulling an IP from the pool I have configured in the IPSec policy.
What would the best way to assign static IPs through VPN?
View 1 Replies
View Related
Mar 14, 2012
A quick query regarding setting up a local user on a Cisco 2811. I have setup a few users as they need to have remote VPN access into our edge router, this works fine and I'm happy with it. The only thing is that when they come into the office they now have logins to get onto the router, they do not have the enable secret so they can't exactly do a lot (plus I've created them with privilege 0 which cuts a few extra CLI options) but I'd rather not allow them access at all if possible.If they weren't on DHCP then I could setup an access-list but this isn't really an option, I could also set me up statically and deny everyone else, but yet again I'd rather not.Is there anyway to restrict telnet/ssh access based on user alone? So when they put in their login it just boots them out. I could setup something like RADIUS (and therefore remove the local users completely) but I think it will be a bit over kill for the sake of a couple of users.
View 1 Replies
View Related
Sep 11, 2012
We are wanting to use local database users to authenticate our SSH connections to our 6500 cores.
We have added the usernames and password into the 6500 using
username anameduser password astrongpassword or username anameduser secret astrongpassword
We where expecting the commands to be the same as other iOS devices example C3750 we would add.
Line vty 0 4 login local
And this would allow us to use the local user database to authenticate our ssh sessions.
The login local commands are not availbe on the 6500s and we have not found any documentation on how to impliment a local database for this purpose except in a CatOS 6500.
View 1 Replies
View Related
May 5, 2011
I have a 3845 router (12.4(13r)T10) with ZBF. On my LAN there is a user who need to access a remote IPSEC VPN server. He is able to get the tunnel but afterwards he cannot connect to any service in the remote LAN. As I'm using zbf I think that I should inspect traffic from my LAN zone to EXT zone, There is a document that describe a solution to this? What IP adressess should I use?
View 2 Replies
View Related
Oct 3, 2011
I have a 3845 router (12.4(13r)T10) with ZBF. On my LAN there is a user who need to access a remote IPSEC VPN server. He is able to get the tunnel but afterwards he cannot connect to any service in the remote LAN. As I'm using zbf I think that I should inspect traffic from my LAN zone to EXT zone
View 3 Replies
View Related
Mar 14, 2011
How i can use both LDAP Authentication and local user database to authenticate the remote vpn clinet in asa 5505?
when i try to do the things either only one method is working both are not working at a time.
View 3 Replies
View Related
Jul 14, 2011
I have FWSM's in Cat 6513's. I have a need to be able to session from the switch to the FWSM by using default account (not local user), at privilege level 15 I further have a need to allow a user read only access by ssh'n into the FWSM...
I believe I need to setup a local user, at, say privilege level 5, assign the show command only to privilege level 5, then set the authorization command for that user. So, i think my command sets are as follows to accomplish this:
username <username> password <pw> priv 5
priv command level 5 mode exec command show
aaa auth ssh console LOCAL
aaa auth enable console LOCAL
aaa authorization command LOCAL
I think, that this will allow the user at privilege 5 to run only the show command and only by SSH to the FWSM while allow the priv 15 level default login to continue to function properly.
View 1 Replies
View Related
Sep 15, 2011
At first I use ACS 4.2 to create static ip address user for remote access VPN,It's easy,just configuration it at user set>Client IP Address Assignment>Assign static IP address,but when I use ACS 5.2 I can't find it.I try to add IPv4 address attribute to user by read "ACS 5.2 user guide" ,it says this: [code] I do this,but it's not work.When I use EasyVPN client to connect ASA 5520,user could through authentication but will not get that static IP address which I configuration on Internal Users.so,what should I do,if anyboby knows how to use ACS 5.2 to create a static ip address user for remote access VPN.
View 2 Replies
View Related
May 5, 2011
i have a ISDN connection i have got 1 static WAN ip and 7 static LAN ip . i have connected it to a server 2008 r2 given that the WAN ip and shared it how do i assisgn 7 LAN static IP in local area network
View 3 Replies
View Related
Sep 14, 2012
I am in need of a Static IP alternative (My ISP chooses not to offer the service). I do not need the Static IP to access my own devices. I need to access other networks as a "trusted" user.
View 10 Replies
View Related
Aug 22, 2011
I have a console access to a Cisco 4500 series router over Cisco access server, which has following "line con 0" configuration:
View 8 Replies
View Related
Jan 12, 2012
I would like to create a additional user vpn on a 55010 where the user authenticates with the firewall and not the radius server.This user should NOT be able to log on to the firewall, but only be able to authenticates with the vpn client.I'm correct that the command "username abc123 password abc234 privilege 0" ?Also for this remote vpn how to I make sure the user only authencates with this password?
View 3 Replies
View Related
