I want to create a local user in my Cisco ASA 5520 to allow the user to use the ASDM in Read-Only mode. I want the user to view the Dashboard only.
View 1 RepliesWhat is the command for creating a user on an ASA 5500 running 7.2(3) that can only view the config but not make any changes?
View 8 Replies View RelatedI have a customer that has a FWSM on a 6500, I want to create a read only account for them, i believe user privelage of lvl_3 When I log into the firewall it prompts me for a password straight away.
Is there a way that i can create a login that when it prompts me for a password, I can have a password setup to put into that prompt to get a certain level of access, instead of the standard lvl_15 access
After pulling a brand new ASA5515 out of the box this morning, I spent countless hours scratching my head wondering why:
1. I cannot establish an HTTPS connection to the Management port - https://192.168.1.1/admin
2. When connecting via the console port I get prompted with a username and password sequence that I don't know
I get an SSL Version Error message when I try to connect with any browser. although I did find a way to resolve it, it requires a console port connection which is not working either.This is not my typical experience with the console or ASDM port setup.
How can i create customized user in Cisco ASA 5505 having the following Privileges? note i dont have AAA server.User can only perform show running, ping, traceroute, show xlate. I have review one of the firewall configuration and found two type of password defined, what is the difference b/w enable and password?
View 2 Replies View RelatedWe are using an ASA 5510 and remote access (SSL VPN) using the AnyConnect client.
Is it possible to display a user message when a user connects using the AnyConnect client, matching a specific dynamic access policy? Can the message be displayed when the action is "Continue" rather than "Terminate"? I can't seem to get this to work and wondered if there was a LUA function to do this.
We have a DAP which gives a restricted ACL when the user's anti-virus is out of date, and I wanted to notify the user to update their anti-virus and reconnect.
I have a 3845 router (12.4(13r)T10) with ZBF. On my LAN there is a user who need to access a remote IPSEC VPN server. He is able to get the tunnel but afterwards he cannot connect to any service in the remote LAN. As I'm using zbf I think that I should inspect traffic from my LAN zone to EXT zone, There is a document that describe a solution to this? What IP adressess should I use?
View 2 Replies View RelatedI have a 3845 router (12.4(13r)T10) with ZBF. On my LAN there is a user who need to access a remote IPSEC VPN server. He is able to get the tunnel but afterwards he cannot connect to any service in the remote LAN. As I'm using zbf I think that I should inspect traffic from my LAN zone to EXT zone
View 3 Replies View RelatedI have FWSM's in Cat 6513's. I have a need to be able to session from the switch to the FWSM by using default account (not local user), at privilege level 15 I further have a need to allow a user read only access by ssh'n into the FWSM...
I believe I need to setup a local user, at, say privilege level 5, assign the show command only to privilege level 5, then set the authorization command for that user. So, i think my command sets are as follows to accomplish this:
username <username> password <pw> priv 5
priv command level 5 mode exec command show
aaa auth ssh console LOCAL
aaa auth enable console LOCAL
aaa authorization command LOCAL
I think, that this will allow the user at privilege 5 to run only the show command and only by SSH to the FWSM while allow the priv 15 level default login to continue to function properly.
I would like to create a additional user vpn on a 55010 where the user authenticates with the firewall and not the radius server.This user should NOT be able to log on to the firewall, but only be able to authenticates with the vpn client.I'm correct that the command "username abc123 password abc234 privilege 0" ?Also for this remote vpn how to I make sure the user only authencates with this password?
View 3 Replies View RelatedIs it possible to have emails stored automatically on a network drive after email is been read by the user? I know for sure that on a mailserver there is a feature that can be set up to have a copy stored and than send it to the users application.
View 1 Replies View RelatedI´m looking for the best configuration to restrict a user to read-only. The restriction should be configured via CLI not TACACS+.
-Hardware: 3750 (probably not interesting for this question)
-Oldest IOS: 12.2(53)SE1
The user should be allowed to: see the running-configurationtrigger all kinds of show-commandsping and traceroute from the device.The user should not be allowed to: upload/delete/rename files on the flash-memoryget into level 15 (not sure if I can avoid this)all other commands despite those from level 1 and those specified above.
i have user connected to office using Cisco vpn client , Cisco asa 5520 acts as vpn gateway, frequently the users got disconnected from the server while the VPN still established and not disconnected!
what is the cause of the issue , where the fault is located ? how to start the troubleshooting to figure out the issue?
Is there a way to create an account for the ASA using ASDM that is only read only and cannot make firewall changes?
View 1 Replies View RelatedI want to create Password and user name of my wireless. so how can I do it?
View 1 Replies View Relatedhow do i create and manage 40 user accounts on a windows 7 PC.
View 1 Replies View RelatedI Need to create more options on Cisco ACS 5.2 under internal identity store in users. How to do add, default not showing all.
View 6 Replies View RelatedI have an instance of ISE and NCS with a WLC 2100 plus a couple of LWAPs. This is an evaluation POC lab to sell ISE and NCS to our management to make our life easier.The problem I have amoungst many is I can create a guest user directly on the ISE and the guest can login, the ISE monitor shows the guest authenticates but the clients webpage passes them back to the login page not onto the original client url. The web auth is pointed at the ISE/guestportal/portal.jsp page.If I point the web auth at the internal WLC page using a WLC local user account it works.If I set the guest access to pass through it works without issues getting dhcp and dns. On the ISE is there a policy needed to say if guests are web authenticated give them access? The need is for AD authenticated users to be able tocreate guest users. The AD authentication works for sponsorship and guest creation its just the guest access redirection I am having issues with.
View 1 Replies View Related(WLC 4400) which enables employees to browse to a custom made webpage, where they can create an account for company vistors to access the internet. It's important for the employees not use any login credentials, they arrive on a webpage where they specify the login & password which the vistor will enter to browse the internet. Is there any good link to documention about this topic?
View 3 Replies View Relatednat global entry not showing up in ASDM but it does via CLI see blow, it's a policy NAT.
nat (inside) 5 access-list inside_nat_outbound_4
global (outside) 5 ************-OUTSIDE netmask 255.0.0.0
Global 5 doesnt show in ASDM 6.1 (5) the globals only go up to 3
At first I use ACS 4.2 to create static ip address user for remote access VPN,It's easy,just configuration it at user set>Client IP Address Assignment>Assign static IP address,but when I use ACS 5.2 I can't find it.I try to add IPv4 address attribute to user by read "ACS 5.2 user guide" ,it says this: [code] I do this,but it's not work.When I use EasyVPN client to connect ASA 5520,user could through authentication but will not get that static IP address which I configuration on Internal Users.so,what should I do,if anyboby knows how to use ACS 5.2 to create a static ip address user for remote access VPN.
View 2 Replies View RelatedI am just wondering if it is possible to have two user accounts in Cisco RV042 V3 (Firmware: v4.1.1.01-sp (Dec 6 2011 20:03:18). User accounts to mean that one user can access the router with an administrative level access can do all the changes and management of the router's configurations and settings while another user can only do viewing of the system summary tab and connect and manage the simple configuration to connection to the ISP in both WANs, like setting up the connection type and release/renew the ip address for dynamic ip assigned by the ISP DHCP server.
View 1 Replies View RelatedI'm trying to create a new ACS 5.3 user via RESTclient (Mozilla plug-in). Which are the header and the body content to send invoking https://172.26.0.72/Rest/Identity/User/ with POST method?
View 2 Replies View RelatedWe are running ACS 5.2 patch 6 and want to restrict access for users to be able to add devices to the system.For example, admin person in site A can only add devices into the site A group and cannot see/access other sites groups.
View 1 Replies View RelatedI want to have a local user in ACS that is permitted to login to routers. I have TACACS with AD already working but cannot get a local user to work. I used to do this in ACS 4.x.I created a user in the internal identity store.I tried configuring a policy to allow this users TACACS authentication multiple ways to no avail. I cannot find a config example doc and cannot figure it out from the user guide as the documention is sorely lacking.
View 5 Replies View RelatedI want to limit a local user's access to some specific groups of devices. In Role Management Setup I can define which service they can access, but I want to restrict it to a specific device as well.
View 3 Replies View RelatedAt first I use ACS 4.2 to create static ip address user for remote access VPN,It's easy,just configuration it at user set>Client IP Address Assignment>Assign static IP address,but when I use ACS 5.2 I dont't know how to do it.
I try to add IPv4 address attribute to user by read "ACS 5.2 user guide" ,it says this:
Step 1Add a static IP attribute to internal user attribute dictionary:
Step 2Select System Administration > Configuration > Dictionaries > Identity > Internal Users.
Step 3Click Create.
Step 4Add static IP attribute.
Step 5Select Users and Identity Stores > Internal Identity Stores > Users.
Step 6Click Create.
Step 7Edit the static IP attribute of the user.
I just do it,but it's not work.When I use EasyVPN client to connect ASA 5520,user could success to authentication but will not get the static IP address which I configure on Internal Users,so the tunnel set up failed.I try to Configure a IP pool on ASA for ACS users get IP address,and use EasyVPN client to connect ASA , everything is OK,user authenticate successed.but when I kill IP pool coufigurations and use the "add a static IP address to user "configurations,EzVPN are failed. how to use ACS 5.2 to create a static ip address user for remote access VPN?
We have installed ACS 4.1 as authentication server for wireless SSID. Need to create list of ACS user expired on specific date.Is it possible to create report in ACS 4.1 as per user account expiry date?
View 3 Replies View RelatedIs it configurable to allow wifi user to user traffic on WLC 5508?
View 4 Replies View RelatedTime Warner used remote access to get into my wrt54g system and create a new user id/password for security. As a result, my hp printer will no longer communicate with my computer. HP says to hook up a usb from router to printer, but there's no usb port on the wrt model I own. I hooked up a usb from computer to printer but it did nada...
View 5 Replies View RelatedA quick query regarding setting up a local user on a Cisco 2811. I have setup a few users as they need to have remote VPN access into our edge router, this works fine and I'm happy with it. The only thing is that when they come into the office they now have logins to get onto the router, they do not have the enable secret so they can't exactly do a lot (plus I've created them with privilege 0 which cuts a few extra CLI options) but I'd rather not allow them access at all if possible.If they weren't on DHCP then I could setup an access-list but this isn't really an option, I could also set me up statically and deny everyone else, but yet again I'd rather not.Is there anyway to restrict telnet/ssh access based on user alone? So when they put in their login it just boots them out. I could setup something like RADIUS (and therefore remove the local users completely) but I think it will be a bit over kill for the sake of a couple of users.
View 1 Replies View Relatedhow I can assign a static IP to a user in ACS 5.2. I am able to do it in ACS 4.2, but I don't see the same options under 5.2. General idea is that users authenticate from our VPN appliance via RADIUS, and upon authentication, their static IP is passed back to the VPN device. I can attach an arbitrary field to my local users by going to System Administration -> Configuration -> Dictionaries -> Identity -> Internal Users, but how do I get that IP address passed back when the user is authenticated via Radius?
View 1 Replies View RelatedWe are wanting to use local database users to authenticate our SSH connections to our 6500 cores.
We have added the usernames and password into the 6500 using
username anameduser password astrongpassword or username anameduser secret astrongpassword
We where expecting the commands to be the same as other iOS devices example C3750 we would add.
Line vty 0 4 login local
And this would allow us to use the local user database to authenticate our ssh sessions.
The login local commands are not availbe on the 6500s and we have not found any documentation on how to impliment a local database for this purpose except in a CatOS 6500.