Cisco :: Setting Up A Local User But Denying Telnet / Ssh?
Mar 14, 2012
A quick query regarding setting up a local user on a Cisco 2811. I have setup a few users as they need to have remote VPN access into our edge router, this works fine and I'm happy with it. The only thing is that when they come into the office they now have logins to get onto the router, they do not have the enable secret so they can't exactly do a lot (plus I've created them with privilege 0 which cuts a few extra CLI options) but I'd rather not allow them access at all if possible.If they weren't on DHCP then I could setup an access-list but this isn't really an option, I could also set me up statically and deny everyone else, but yet again I'd rather not.Is there anyway to restrict telnet/ssh access based on user alone? So when they put in their login it just boots them out. I could setup something like RADIUS (and therefore remove the local users completely) but I think it will be a bit over kill for the sake of a couple of users.
View 1 Replies
ADVERTISEMENT
Oct 10, 2011
I want to create a local user in my Cisco ASA 5520 to allow the user to use the ASDM in Read-Only mode. I want the user to view the Dashboard only.
View 1 Replies
View Related
Feb 7, 2013
I have "transport local ssh" but its still allowing telnet??This is a 2960 switch Here is the end of running config:
Code:
View 6 Replies
View Related
Jun 17, 2011
how do i change the telnet and enable and vpn user password on asa 5570.
View 4 Replies
View Related
Jan 21, 2013
We are running in our DC one of the CISCO 2911 terminal server which is connected with HP ARC sight logger.
it is possible to capture user who execute ‘Telnet” or “show line” in the log, I mean all the command entries by user.
How to enable any config on 2911.
View 11 Replies
View Related
Nov 12, 2012
I want to have a local user in ACS that is permitted to login to routers. I have TACACS with AD already working but cannot get a local user to work. I used to do this in ACS 4.x.I created a user in the internal identity store.I tried configuring a policy to allow this users TACACS authentication multiple ways to no avail. I cannot find a config example doc and cannot figure it out from the user guide as the documention is sorely lacking.
View 5 Replies
View Related
Nov 14, 2012
I want to limit a local user's access to some specific groups of devices. In Role Management Setup I can define which service they can access, but I want to restrict it to a specific device as well.
View 3 Replies
View Related
Jun 7, 2011
how I can assign a static IP to a user in ACS 5.2. I am able to do it in ACS 4.2, but I don't see the same options under 5.2. General idea is that users authenticate from our VPN appliance via RADIUS, and upon authentication, their static IP is passed back to the VPN device. I can attach an arbitrary field to my local users by going to System Administration -> Configuration -> Dictionaries -> Identity -> Internal Users, but how do I get that IP address passed back when the user is authenticated via Radius?
View 1 Replies
View Related
Sep 11, 2012
We are wanting to use local database users to authenticate our SSH connections to our 6500 cores.
We have added the usernames and password into the 6500 using
username anameduser password astrongpassword or username anameduser secret astrongpassword
We where expecting the commands to be the same as other iOS devices example C3750 we would add.
Line vty 0 4 login local
And this would allow us to use the local user database to authenticate our ssh sessions.
The login local commands are not availbe on the 6500s and we have not found any documentation on how to impliment a local database for this purpose except in a CatOS 6500.
View 1 Replies
View Related
Feb 9, 2010
I know the way to configure the ASA to fallback to LOCAL authentication, if the Radius server is not available.
Now we would like to authenticate the local users, if the user is not found in the AD. Is this possible and how can I configure this with the new policies? I tested it with "dropping" when the user is not found in the AD, but then the Radius server will be marked as "dead" and the other AD users can't login for a given period. Maybe we can configure the dead time to 0, but this is not as nice it could be.
View 4 Replies
View Related
May 5, 2011
I have a 3845 router (12.4(13r)T10) with ZBF. On my LAN there is a user who need to access a remote IPSEC VPN server. He is able to get the tunnel but afterwards he cannot connect to any service in the remote LAN. As I'm using zbf I think that I should inspect traffic from my LAN zone to EXT zone, There is a document that describe a solution to this? What IP adressess should I use?
View 2 Replies
View Related
Oct 3, 2011
I have a 3845 router (12.4(13r)T10) with ZBF. On my LAN there is a user who need to access a remote IPSEC VPN server. He is able to get the tunnel but afterwards he cannot connect to any service in the remote LAN. As I'm using zbf I think that I should inspect traffic from my LAN zone to EXT zone
View 3 Replies
View Related
Mar 14, 2011
How i can use both LDAP Authentication and local user database to authenticate the remote vpn clinet in asa 5505?
when i try to do the things either only one method is working both are not working at a time.
View 3 Replies
View Related
Jul 14, 2011
I have FWSM's in Cat 6513's. I have a need to be able to session from the switch to the FWSM by using default account (not local user), at privilege level 15 I further have a need to allow a user read only access by ssh'n into the FWSM...
I believe I need to setup a local user, at, say privilege level 5, assign the show command only to privilege level 5, then set the authorization command for that user. So, i think my command sets are as follows to accomplish this:
username <username> password <pw> priv 5
priv command level 5 mode exec command show
aaa auth ssh console LOCAL
aaa auth enable console LOCAL
aaa authorization command LOCAL
I think, that this will allow the user at privilege 5 to run only the show command and only by SSH to the FWSM while allow the priv 15 level default login to continue to function properly.
View 1 Replies
View Related
Aug 22, 2011
I have a console access to a Cisco 4500 series router over Cisco access server, which has following "line con 0" configuration:
View 8 Replies
View Related
Jan 12, 2012
I would like to create a additional user vpn on a 55010 where the user authenticates with the firewall and not the radius server.This user should NOT be able to log on to the firewall, but only be able to authenticates with the vpn client.I'm correct that the command "username abc123 password abc234 privilege 0" ?Also for this remote vpn how to I make sure the user only authencates with this password?
View 3 Replies
View Related
May 15, 2012
i am running NX-OS image n5000-uk9.5.1.3.N1.1.bin on the nexus 5020 platform.i have configured authorization with tacacs+ on ACS server version 5.2 with fall back to switch local database.a user test with priv 15 is craeted on ACS server, password test2 everything works fine, until i create the same username on the local database with privilege 0. ( it doesnt matter if the user in local database was created before user in ACS or after ) e.g.: username test password test1 role priv-0 (note passwords are different for users in both databases)
after i create the same user in local database with privilege 0,if i try to connect to the switch with this username test and password defined on ACS, i get only privilege 0 authorization, regardless, that ACS server is up and it should be primary way to authenticate and authorizate the user.
View 3 Replies
View Related
Apr 28, 2011
I am trying to configure an ASA 5505 running 8.3 to allow a priv 15 local user to be able to ssh into the device and be placed into priv 15 mode without having to execute the enable command and type the enable password.Right now when you log in as a priv 15 user you still have to execute the enable command and type the enable password to get to priv 15.
View 3 Replies
View Related
Oct 3, 2012
I'm a bit new to Cisco and i find this AAA a bit confusing..I've turend on AAA by:aaa new-model
Can I use this "default" list for WebVPN ? And what would be a different if i create new "sslvpn" list..Also when I'll be creating user for VPN remote access.. that user will also exist in local database and have access to router via SSH?Because the research I've done it doesn't seem you can group users in different "aaa groups" e.g. user admin belongs under "admin" aaa group which can do ssh to router, users for VPN can only do remote VPN access and not SSH and login into router.i saw ASA has some attribute for users called remote-user
•admin, in which users are allowed access to the configuration mode. This option also allows a user to connect via remote access.
•nas-prompt, in which users are allowed access to the EXEC mode.
•remote-access, in which users are allowed access to the network.
But i can't find this option in IOS on my 1900 Series ISR router.
View 1 Replies
View Related
Jan 13, 2013
I have a Cisco ASA 5505 that I've setup with an SSL VPN. This is for personal use, and I therefore don't have need for anything more than local authentication. [code]
I'd like to have one profile/policy where I only encrypt data going to my split-tunnel ACL, and I'd like to have one profile/policy where I encrypt all traffic.
The issue ive been fighting is - it doesn't seem like its possible to associate more than one group policy per user. If it IS possible - can you tell me how I associate both groups to my local account?
View 1 Replies
View Related
Jan 15, 2013
have a Cisco RV120W and I need setup a Quick VPN user, however i can't enable this user.I have Remote Management enable, access type All Ip Address and port number 443.
View 3 Replies
View Related
Mar 6, 2012
I am migrating an asa 5520 from 8.2 to 8.3 and after the migration the ACL's are blocking access to the DMZ. It looks like the NAT functions were migrated properly by the migration tool but now when I try to access devices in the DMZ the ACL is denying the traffic because my acls in 8.2 had the NATTED IP, not the real IP in the ACL. Now it looks like 8.3 is looking for the real IP and not the NATTED IP.
Here is an example:
Inside network: 172.24.0.0/24
DMZ server real IP: 1.1.1.1
DMZ server NAT IP 2.2.2.2
so, in 8.2 I would have an ACL on the inside interface that said permit 172.24.0.0/24 to 2.2.2.2 eq 80, 443. This acl doesn't work in my 8.3 config because it wants: permit 172.24.0.0/24 to 1.1.1.1 eq 80, 443.
Is this correct for 8.3 or are my NAT rules all messed up after the migration?
View 2 Replies
View Related
Apr 23, 2013
I'm having a (fairly common) problem with my ASA in that I cannot get traffit to pass through it. I can't determine the source of this problem and need getting traffic from my inside network (10.1.2.1, please ignore anything labled 192.168.X.X) to my outside network.
-The border router can ping the Internet, itself, and the ASA's outside int (10.1.1.2)
-The ASA can ping everything
-An ASDM can connect and can manage the ASA via the 10.1.3.2 management cloud
-The inside router (R2) can ping the inside int of the ASA but not the outside
I've tried in both the CLI and ASDM to: -Add network objects to prepare configuring NAT (objects required after 8.3 I believe) -Configure NAT (static) -Configure ACL's to allow any traffic in any direction (just for these initial testing purposes) -Allow ICMP inspection (which was weird because my ASA had no global_policy and I had to make one)
The ASDM doesn't show any logging traffic when I try to ping from R2 (192.168.150.150 or old 10.1.2.2) to my Border (either ints, both being inside 10.1.1.1 and outside 172.16.68.190). Again, I can't even ping the outside int of the ASA from R2. [code]
View 10 Replies
View Related
Aug 15, 2012
We are implementing an ASA 5510 firewall with DMZ. Our UDP packets are able to get outside the firewall, but our TCP packets are being denied because of no connection. I've attached the config file and log file.
View 2 Replies
View Related
Apr 9, 2013
Device Cisco ASA
Model:5520
OS 8.4(2)
I am not able to access the device via SSH .After connecting to teh console I have found that allowed SSh session are fully utilized with show resource usage command and the output is [code]
So I used show ssh session command to see who is using the sessions but in the output it has showed only one session and the output was [code]
I was wondering why it shows only one session above instead of showing all the 5 sessions which are utilized as confirmed by show resource usge command.We are usning some internal tool for ssh monitoring on device which is poling the device after a fixed interval for port 22 reachabilty .I dont think these tools are making any issue as this is secondary firewall and we are not facing any reachabilty issue for primary firewall.also we are using 10 min for idle ssh timeout.
View 13 Replies
View Related
Sep 4, 2012
Why is it that when SNMPv3 user "TestV3-User" was added to my SNMPv3 implementation on my 6506 switch, the group/MD5/Emcryption settings are missing for this user (See "sh snmp user" output)???
router#sh snmp user
User name: TestV3-User
Engine ID: 80000009030000249706EFC0
storage-type: nonvolatile active access-list: test
[Code]....
View 3 Replies
View Related
Aug 29, 2011
We want to set up a wireless user group in our town between a few friends and new people who are interested to join. As far as I heard I don't need a ICASA License for the 5.8GHz Frequency if we are using it for a non profit orginization, so we may use that.
1 x Routerboard
3 x Radio Plugin Boards
3 x 120degree Antennas
to set up a 360degree HS (Highsite).Then at each person's house we will need:
1 x Routerboard
1 x Radio Plugin Board
1 x Whichever Antenna
Is that correct? Then also if we wanto run VoIP on our network, how do I do that? Basicly we want to use it for gaming, file sharing and VoIP. No Internet of anything else.
View 2 Replies
View Related
May 7, 2013
One of our customer , where there 2 6509 switch , one is Core_sw1 and other is Core_sw2 , catering about 32 Vlan , and HSRP in running for all Vlans , till here no problem , now there internet Router which having one Internet link , which connected and configured on Core_sw1 in a way that one interface of Core_sw1 is given Public IP and there is vlan 85 which internet vlan and vlan 85 ip are natted with that public IP with one simple static route given toward internet router , this is how internet is working ok.
Now i have configured vlan 85 in hsrp as all other are , how can give redundancy to vlan 85 user , that if Core_sw1 get down , internet traffic can get out through Core_sw2.using same internet router with single internet link .i am not talking of ISP redundancy , but Vlan 85 in Core_sw1 goes down , other Core_sw2 will server internet.
View 1 Replies
View Related
Mar 13, 2011
What I'm trying to do is create a private network for local file sharing but also have internet access. There is a WRT54G router connected to a satellite modem in a separate building, just barely close enough to connect from my laptop, which is what sparked my original idea to use my WRT54GL as an access point.
View 1 Replies
View Related
Jun 5, 2012
I've been playing around with my E4200 but cannot find the right combination of settings. My problem: I bought the router for cable internet that never happened. In the meantime I am accessing the web using a 3G dongle. Hoewever, while connected to the router (wired or wireless), all the PC's in my home refuses to access the 3G internet - it is as if it wants to use the E4200 to access the net, no matter what. So every time I want to access the internet, I have to disconnect the PC from the home network, and connect with the 3G on that particulat PC. (I have three PC's at home, 1 wired and two wireless). If I set the E4200 to bridge mode, I struggle to find a logical IP address, since I would ideally like to run the network at 192.168.1.X. How do I set the E4200 to allow a home network to be established without having to disconnect everytime I use the 3G on a PC? Also, it seems that if the router doesn't handle the DHCP duties, win7 by default makes the network public, which complicates sharing a lot...
View 5 Replies
View Related
Mar 18, 2013
I've got a 3750x stack set up as my core switch (only a small-ish environment) - I'm shortly going to be deploying an enterprise wireless network with Corporate and Guest SSID's. I'm going to be putting all traffic from the Guest SSID in VLAN 244, and don't want it to have access to any of the other VLANs (1 (Legacy Eqpt), 4, 8, 12, 16, 20, 24, 28, 32, 248 & 252).
IP ranges for all the main VLANs are:
1: 10.0.0.x/22
4: 10.0.4.x/22
8: 10.0.8.x/22
12: 10.0.12.x/22
16: 10.0.16.x/22 etc etc (you get the pattern)
I'll probably give Guest traffic (VLAN 248) the IP range 192.168.10.x/22 (not because I NEED that many addresses, but it's easier for everyone to remember/understand if I keep the subnet masks the same all round). However I also have a CCTV VLAN (252) which already has the range 192.168.0.x/24, which some people in other VLANs WILL need access to.
So my question is: What is the syntax for the ACL on my 3750x (IP base - 15.0.2) to prevent traffic from VLAN 244 gaining access to any of my other VLANs. I'm making a broad assumption here that a layer 3 switch is perfectly capable of supporting that function? I need ALL the syntax for setting up ACL's - I've never done it before
My gateway device by the way is 10.0.4.1, and I do have inter-VLAN routing set up on the core switch (obviously).
View 3 Replies
View Related
Sep 22, 2011
We are running ACS 5.2 patch 6 and want to restrict access for users to be able to add devices to the system.For example, admin person in site A can only add devices into the site A group and cannot see/access other sites groups.
View 1 Replies
View Related
Apr 20, 2009
We are using an ASA 5510 and remote access (SSL VPN) using the AnyConnect client.
Is it possible to display a user message when a user connects using the AnyConnect client, matching a specific dynamic access policy? Can the message be displayed when the action is "Continue" rather than "Terminate"? I can't seem to get this to work and wondered if there was a LUA function to do this.
We have a DAP which gives a restricted ACL when the user's anti-virus is out of date, and I wanted to notify the user to update their anti-virus and reconnect.
View 4 Replies
View Related
