Cisco Routers :: Create Another Account With User Privileges In RV042 V3?
Jul 26, 2012
I am just wondering if it is possible to have two user accounts in Cisco RV042 V3 (Firmware: v4.1.1.01-sp (Dec 6 2011 20:03:18). User accounts to mean that one user can access the router with an administrative level access can do all the changes and management of the router's configurations and settings while another user can only do viewing of the system summary tab and connect and manage the simple configuration to connection to the ISP in both WANs, like setting up the connection type and release/renew the ip address for dynamic ip assigned by the ISP DHCP server.
How can i create customized user in Cisco ASA 5505 having the following Privileges? note i dont have AAA server.User can only perform show running, ping, traceroute, show xlate. I have review one of the firewall configuration and found two type of password defined, what is the difference b/w enable and password?
We have installed ACS 4.1 as authentication server for wireless SSID. Need to create list of ACS user expired on specific date.Is it possible to create report in ACS 4.1 as per user account expiry date?
After installing the RV042, we can no longer log in to our business bank account. My personal account works but it is a different bank. What could be causing this ?
I have a Cisco ASA 5505 and a Cisco/Linksys RV042. I would like to crerate a site to site VPN between them, and from what I've read it is possible. So I set up the connection on both routers but When I click on connect on the RV042 nothing happens. I've made sure that the encryption settings are the same on both routers but I can't get them to connect to each other. I think the problem may be with the RV042 as the ASA has other site to site VPN connections without any proble (although they are on other ASAs). I saw this thread [URL] but I'm not sure how to disable phase 2 on the RV042 or enable it on the ASA.
what setting I need to change on either router to make the site to site work?
Im able to create a gateway tunnel with two rv042 routers in different locations ( i can see the tunnel connected in the router) but the quick vpn utility is not working , i also tried to use the pptp as server as an alternative( im able to connect using windows connection to the pptp server but whenever I browse any of the four ip's allowed for the pptp server \10.0.0.200-204 it takes me to the documents of the local computer....I attached the configuration for one of the routers it is the same as the other end , just the information is flipped.
I upgraded my Linksys RV042 firmware to 1.3.12.19-tm and exported the config file, then tried to convert it using RV0xx_Migration_Utility_v1.0.2.2 in order to import it to a new Cisco RV042 (v3). The migration utility returns a config create fail message and fails to convert.
The LOG file ends with:
Get PORT_101 VLAN Group setting fail. ***log end***
how to make this work or how to move config file to v3?
I recently purchased a RV042 device but when I tried to set my DDNS account I realized that the only two providers are dyndns.org and 3322.net. We already have an account in no-ip.com and several services using the [URL] host.
Any detailed knowledge about Cisco ACS 5.1 and Windows AD interaction? I wonder why does Cisco ACS domain account must have permission to create/delete domain objects. This fact does really surprided me, because to my mind Cisco ACS only reads domain structure, and does not make any changes.
I have an ACS 5.2 server integrated with Active directory . Now i need to create an internal user account to login to some radisu devices using internal user database .I have near about 600 users all are authenticating through AD .
how to limit bandwidth only for user account in window 7...My PC has 2 account ..one is admin and other is user ..i need to limit the bandwidth only for user account ,do I need a software for this.
I have a laptop with 2 user account (one for me - administrator and the other for my eleven year old son). Connection is wireless. Until a few months ago everything was working fine and then the problems started: my son could no longer connect on the internet with Explorer and Google Chrome but I managed to connect it via Firefox. And it worked until yesterday. As of yesterday he can no longer connect to the internet even with Firefox. I tried again as an administrator to reinstall Google Chrome, but the icon is shown only on my user account. I took a completely new browser - Opera, but fails to connect. When I go to Diagnose & Repair connection problems - shows no problems. On my account everything is working properly. OS is Windows Vista Home Premium
While I was at school there was a system in place where by you had to enter a user name and password to access the internet. Every student had a data limit like 3GB per month for example. I remember it had something to do with a proxy. I would like to recreate this system on my office LAN as some staff members have been downloading a lot slowing down the (very expensive) Internet connection. Limiting each users data will discourage large downloads.
I have setup ACS 5.2 in my lab and have it completely funcation with Downloadable ACLs, Dynamic VLANs and the identity store on the backend is Active Directory. I need it to lock a user account in AD if there are to many auth attempts. I have gone into AD and set a max login attempts to 3 but if I continue to fail authentication (on purpose) using radius auth, it never locks out my AD account? I am using the Anyconnect 3.0 with NAM as the supplicant installed on my workstation. I have also configured the switchport that I am connect to with the following commands. I tried the dot1x max-reauth-req 3 command and that didn't really do anything for me either. What am I missing here?
We had a power outage that kicked off our server and our network switch (2008R2, Cisco2960), before we could get it back up, a user was able to log into his laptop.
The user used the domain login - not the local machine account - he obviously wasn't able to access any shared resources, but how did he log in with a domain account, when the server and switch were both off?
I would like to create a additional user vpn on a 55010 where the user authenticates with the firewall and not the radius server.This user should NOT be able to log on to the firewall, but only be able to authenticates with the vpn client.I'm correct that the command "username abc123 password abc234 privilege 0" ?Also for this remote vpn how to I make sure the user only authencates with this password?
how to set WLC 5508 to allow single create web authentication user account to get connected in a same time. i found that i can use the same username and password combo to be login in 2 machine in the same time.
I am having problems with my RV042.I have a Intervoip(url...) account for VOIP.
When I try to register the intervoip account to the internet I don't get any kind of reply. My VOIP server just keeps requesting to register the SIP account, but gets no reply.
When I connect an other router to my ISP modem, the register just goes fine. However the RV042 blocks something I don't really know what the cause could be.I installed wireshark to monitor my network traffic.
When I monitor registering with intervoip with the RV042, I see requests but no replies from intervoip, the VOIP server keeps requesting, but doesn't get any reply.
When I monitor registering with intervoip with an other router, I see requests from the VOIP server, and replies from intervoip initiating my intervoip account and everything goes well and registers. The following I tried:
I have an instance of ISE and NCS with a WLC 2100 plus a couple of LWAPs. This is an evaluation POC lab to sell ISE and NCS to our management to make our life easier.The problem I have amoungst many is I can create a guest user directly on the ISE and the guest can login, the ISE monitor shows the guest authenticates but the clients webpage passes them back to the login page not onto the original client url. The web auth is pointed at the ISE/guestportal/portal.jsp page.If I point the web auth at the internal WLC page using a WLC local user account it works.If I set the guest access to pass through it works without issues getting dhcp and dns. On the ISE is there a policy needed to say if guests are web authenticated give them access? The need is for AD authenticated users to be able tocreate guest users. The AD authentication works for sponsorship and guest creation its just the guest access redirection I am having issues with.
(WLC 4400) which enables employees to browse to a custom made webpage, where they can create an account for company vistors to access the internet. It's important for the employees not use any login credentials, they arrive on a webpage where they specify the login & password which the vistor will enter to browse the internet. Is there any good link to documention about this topic?
At first I use ACS 4.2 to create static ip address user for remote access VPN,It's easy,just configuration it at user set>Client IP Address Assignment>Assign static IP address,but when I use ACS 5.2 I can't find it.I try to add IPv4 address attribute to user by read "ACS 5.2 user guide" ,it says this: [code] I do this,but it's not work.When I use EasyVPN client to connect ASA 5520,user could through authentication but will not get that static IP address which I configuration on Internal Users.so,what should I do,if anyboby knows how to use ACS 5.2 to create a static ip address user for remote access VPN.
I'm trying to create a new ACS 5.3 user via RESTclient (Mozilla plug-in). Which are the header and the body content to send invoking https://172.26.0.72/Rest/Identity/User/ with POST method?
At first I use ACS 4.2 to create static ip address user for remote access VPN,It's easy,just configuration it at user set>Client IP Address Assignment>Assign static IP address,but when I use ACS 5.2 I dont't know how to do it.
I try to add IPv4 address attribute to user by read "ACS 5.2 user guide" ,it says this:
Step 1Add a static IP attribute to internal user attribute dictionary: Step 2Select System Administration > Configuration > Dictionaries > Identity > Internal Users. Step 3Click Create. Step 4Add static IP attribute. Step 5Select Users and Identity Stores > Internal Identity Stores > Users. Step 6Click Create. Step 7Edit the static IP attribute of the user.
I just do it,but it's not work.When I use EasyVPN client to connect ASA 5520,user could success to authentication but will not get the static IP address which I configure on Internal Users,so the tunnel set up failed.I try to Configure a IP pool on ASA for ACS users get IP address,and use EasyVPN client to connect ASA , everything is OK,user authenticate successed.but when I kill IP pool coufigurations and use the "add a static IP address to user "configurations,EzVPN are failed. how to use ACS 5.2 to create a static ip address user for remote access VPN?
We are planning to setup a new WLAN using Cisco 2504 WLAN Controller and 1142N Access Point.Is it possible to create individual user accounts for the users those who all are connecting to this WLAN Network by using the 2504 WLAN Controller ?
