how to limit bandwidth only for user account in window 7...My PC has 2 account ..one is admin and other is user ..i need to limit the bandwidth only for user account ,do I need a software for this.
View 3 RepliesI live in rural Alaska and use satellite internet with 1.5mbps rate and 4gb rolling weekly download limit. I was wondering if there are any wireless routers I can buy that I can set a bandwidth limit for the specific router. Due to teenage girls in the house we hit the weekly limit in a day or two because of all the music videos and such that they watch on you tube, it is annoying getting limited to the 256kbps download rate so often.
View 5 Replies View RelatedI am a gamer living in my apartment with a room mate who loves to download music 24/7 and a girlfriend who loves to watch netflix. Needless to say, every time I go to play a video game I get shitty ping and lots of lag. From what I've gathered, DD-WRT's QOS is ****, and Tomato is the way to go in 3rd party firmware.
View 1 Replies View RelatedWithout using another box as a router preferably. My Cisco Linksys router doesn't have any options for this but I heard you could possibly install some 3rd party firmware to get around that. This would be a last resort for me What I'm hoping for his some piece of software that could do this
View 2 Replies View RelatedI run a business and have customers who would like to use my wireless internet. I previously had a completely open network that I would allow them to use, until someone illegally downloaded a movie and got us in trouble. I would like to allow use of the network again, but limit activities like this. Basically, so they could only do basic web browsing, etc.
View 1 Replies View RelatedWe have two Cisco 2811 Routers setup with a GRE tunnel that we would like to constrain the bandwidth on to replicate a satellite connectinon of 400 kbits. We tried the bandwidth command 400, but from what I understand that is only for routing metrics and not actual speed of the interface.
View 5 Replies View RelatedI have a SG 300-20 small business switch and I would like to restrict bandwidth by gateway ip address but not by physical port or LAG. On the web interface, I can only do bw limiting per port or lag. I want to do bandwidth limiting by the IP addresses that I assign to vlans that my hosts use as a gateway ip.
View 3 Replies View RelatedI have a Cisco ASA5510 with two Cisco Catalyst 3560G switches plugged into it. Then I have 2 Cisco1400 Aironet WAPs plugged into the switches.
My goal is to limit incoming bandwith for two specific vlans. So users who are plugged into the switch or connected to the wifi can't go bandwidth crazy.
The rule I currently have setup on the ASA5510 is limiting internal bandwidth, I know shame on me.
So how do I setup a rule on the ASA5510 that will limit users external traffic on vlans without limit internal lan traffic?
I have an RV220W which I would like to set bandwidth limiting on. When we upload files to yousendit or an FTP server, it saturates the connection and essentially stops any other traffic until the upload is finished. Looking at the manual, it looks like it should do this, but does not seem clear to me.
View 1 Replies View RelatedSo my ISP (Telus) recently replaced our old router with a ZyXEL VSG1432. I'm currently having a huge lag issue when my roommates laptop is connected to our network. He is connected via wireless, I'm wired. So I did some searching around and I think i can solve this by limiting his bandwidth with QoS settings. I'm getting conflicting information here though. After logging into the router there are no QoS options yet according to ZyXEL's website url...This router should have the settings available. Is it possible that Telus does something to remove this feature? Is there some not so obvious way to enable QoS? Is there some other way to limit the bandwidth?
View 1 Replies View RelatedI currently use Verizon FiOS 20/5. The speed has been great until the day my cousin and his parents moved in. They also use our FiOS connection and I have came to the conclusion that my cousin's laptop is eating away all of the bandwidth which makes all devices using FiOS have extremely slow internet speeds. I know it is his computer because I logged in as admin to the Verizon FiOS page (192.168.1.1) and I saw that he is using several P2P applications and downloading torrents as well. Is there a way I can limit the bandwidth he is using so that the internet speed can improve? I looked at the QoS tab and tried to play around with the settings, but I don't want to mess it up. The router I have is Actiontec M1424-WR (Verizon FiOS 20 Down/5 Up). A lot of sources I am reading says that I have to use the QoS, but I don't know how to use it on the site.
View 3 Replies View RelatedI will have this one router. Its f0/0 will be for the Internet connection with bandwidth of 30Mbps. Its f0/1 will be connected to a switch for internal networks. This link will be separated to 3 VLANs for 3 internal networks. I'm wondering if there is a way to gurantee 10Mbps for each VLAN but allow use up to 30Mbps when another two VLANs are not using any Internet bandwidth? I only worry about download bandwidth from internet.The 3 internal networks will all have public IPs and they belong to their own subnets. There won't be NAT/PAT.
View 18 Replies View RelatedWe have a new 100MB internet service, but we only pay for 10MB and above that is a per/MB fee and not cheap. I want to limit all traffic inbound and outbound only to use up to 10MB on the outside interface of our Cisco 3825.
View 9 Replies View Relatedhow i can limit the bandwidth for a all my client conect to the AP, i have a Aironet 1200 with the 12.2.15 code.
View 3 Replies View RelatedI have a 4500 and 6500 that I'd like to be able to limit the bandwidth of layer 2 switchports. So for instance I have all GB blades but certain servers I'd like only to have connections of about 5 Mb per second or 15 Mb per second etc.
View 1 Replies View RelatedMy QA team needs to test number of special connectivity scenarios where their wireless connection has a limited bandwidth.Ideally, I would like to provide them number of SSIDs each of which has different bandwidth limitation.But so far I did not find a way to apply any bandwidth limitations to my 2504 Wireless controller and the 3602E AP.QoS has only 4 pre-defined modes which can't be set to a specific limit.
View 10 Replies View RelatedI 3750 doesn't support "shape" command under policy map. How do I limit the bandwidth to 3 M? [code]
View 3 Replies View RelatedCan I limit bandwith for guest in a wlan network with out Wlan controller? and of course, how can I do it?P.S.: I heard something about bronze profile in a wlan controller envoiroment, I need something like that but in an independent AP.
View 3 Replies View RelatedAny idea for limiting bandwidth on cisco 892F router? We have 2 VLANs through our LAN and one must be limited upto 1Mbps or 512Kbps.
View 2 Replies View RelatedWe have a guest wireless setup but I need to rate limit the users so no one hogs all the bandwidth. The WLC is connected into a 3750 which is doing all the routing between the vlans. I know I cannot shape the traffic on the 3750.
View 2 Replies View RelatedHow do I setup this on the SRP527W? I already block most of the video stuff on the internet. But I want to make this one more step.
View 1 Replies View Relatedhow to perform UBRL User Based Rate Limiting on ASR1000 like we can do it on Catalyst6500?
View 3 Replies View RelatedHow to restrict internet particular user account in pc
View 1 Replies View Relatedhow many unsucessful attempts a user has to access the LMS application prior to the account being locked? Is this configurable?
View 3 Replies View RelatedI have a laptop with 2 user account (one for me - administrator and the other for my eleven year old son). Connection is wireless. Until a few months ago everything was working fine and then the problems started: my son could no longer connect on the internet with Explorer and Google Chrome but I managed to connect it via Firefox. And it worked until yesterday. As of yesterday he can no longer connect to the internet even with Firefox. I tried again as an administrator to reinstall Google Chrome, but the icon is shown only on my user account. I took a completely new browser - Opera, but fails to connect. When I go to Diagnose & Repair connection problems - shows no problems. On my account everything is working properly. OS is Windows Vista Home Premium
View 2 Replies View RelatedWhile I was at school there was a system in place where by you had to enter a user name and password to access the internet. Every student had a data limit like 3GB per month for example. I remember it had something to do with a proxy. I would like to recreate this system on my office LAN as some staff members have been downloading a lot slowing down the (very expensive) Internet connection. Limiting each users data will discourage large downloads.
View 1 Replies View Relatedi have cisco ACS 5.2 and want to create user account for technician, with only certain commands.
View 3 Replies View RelatedWe had a power outage that kicked off our server and our network switch (2008R2, Cisco2960), before we could get it back up, a user was able to log into his laptop.
The user used the domain login - not the local machine account - he obviously wasn't able to access any shared resources, but how did he log in with a domain account, when the server and switch were both off?
I have an ACS 5.2 server integrated with Active directory . Now i need to create an internal user account to login to some radisu devices using internal user database .I have near about 600 users all are authenticating through AD .
View 3 Replies View RelatedI am just wondering if it is possible to have two user accounts in Cisco RV042 V3 (Firmware: v4.1.1.01-sp (Dec 6 2011 20:03:18). User accounts to mean that one user can access the router with an administrative level access can do all the changes and management of the router's configurations and settings while another user can only do viewing of the system summary tab and connect and manage the simple configuration to connection to the ISP in both WANs, like setting up the connection type and release/renew the ip address for dynamic ip assigned by the ISP DHCP server.
View 1 Replies View RelatedI have setup ACS 5.2 in my lab and have it completely funcation with Downloadable ACLs, Dynamic VLANs and the identity store on the backend is Active Directory. I need it to lock a user account in AD if there are to many auth attempts. I have gone into AD and set a max login attempts to 3 but if I continue to fail authentication (on purpose) using radius auth, it never locks out my AD account? I am using the Anyconnect 3.0 with NAM as the supplicant installed on my workstation. I have also configured the switchport that I am connect to with the following commands. I tried the dot1x max-reauth-req 3 command and that didn't really do anything for me either. What am I missing here?
switchport mode access ip access-group 10 in authentication event fail action authorize vlan 40 authentication event no-response action authorize vlan 40 authentication host-mode multi-host authentication priority dot1x mab authentication port-control auto authentication timer reauthenticate 10 authentication timer inactivity 20 authentication violation protect mab dot1x pae authenticator dot1x timeout quiet-period 5 dot1x timeout tx-period 5 dot1x max-req 3 spanning-tree portfast
I would like to create a additional user vpn on a 55010 where the user authenticates with the firewall and not the radius server.This user should NOT be able to log on to the firewall, but only be able to authenticates with the vpn client.I'm correct that the command "username abc123 password abc234 privilege 0" ?Also for this remote vpn how to I make sure the user only authencates with this password?
View 3 Replies View Relatedhow to set WLC 5508 to allow single create web authentication user account to get connected in a same time. i found that i can use the same username and password combo to be login in 2 machine in the same time.
View 4 Replies View Related