I am a gamer living in my apartment with a room mate who loves to download music 24/7 and a girlfriend who loves to watch netflix. Needless to say, every time I go to play a video game I get shitty ping and lots of lag. From what I've gathered, DD-WRT's QOS is ****, and Tomato is the way to go in 3rd party firmware.
View 1 Replies
I live in rural Alaska and use satellite internet with 1.5mbps rate and 4gb rolling weekly download limit. I was wondering if there are any wireless routers I can buy that I can set a bandwidth limit for the specific router. Due to teenage girls in the house we hit the weekly limit in a day or two because of all the music videos and such that they watch on you tube, it is annoying getting limited to the 256kbps download rate so often.
View 5 Replies View RelatedWithout using another box as a router preferably. My Cisco Linksys router doesn't have any options for this but I heard you could possibly install some 3rd party firmware to get around that. This would be a last resort for me What I'm hoping for his some piece of software that could do this
View 2 Replies View RelatedI run a business and have customers who would like to use my wireless internet. I previously had a completely open network that I would allow them to use, until someone illegally downloaded a movie and got us in trouble. I would like to allow use of the network again, but limit activities like this. Basically, so they could only do basic web browsing, etc.
View 1 Replies View Relatedhow to limit bandwidth only for user account in window 7...My PC has 2 account ..one is admin and other is user ..i need to limit the bandwidth only for user account ,do I need a software for this.
View 3 Replies View RelatedWe have two Cisco 2811 Routers setup with a GRE tunnel that we would like to constrain the bandwidth on to replicate a satellite connectinon of 400 kbits. We tried the bandwidth command 400, but from what I understand that is only for routing metrics and not actual speed of the interface.
View 5 Replies View RelatedI have a SG 300-20 small business switch and I would like to restrict bandwidth by gateway ip address but not by physical port or LAG. On the web interface, I can only do bw limiting per port or lag. I want to do bandwidth limiting by the IP addresses that I assign to vlans that my hosts use as a gateway ip.
View 3 Replies View RelatedI have a Cisco ASA5510 with two Cisco Catalyst 3560G switches plugged into it. Then I have 2 Cisco1400 Aironet WAPs plugged into the switches.
My goal is to limit incoming bandwith for two specific vlans. So users who are plugged into the switch or connected to the wifi can't go bandwidth crazy.
The rule I currently have setup on the ASA5510 is limiting internal bandwidth, I know shame on me.
So how do I setup a rule on the ASA5510 that will limit users external traffic on vlans without limit internal lan traffic?
I have an RV220W which I would like to set bandwidth limiting on. When we upload files to yousendit or an FTP server, it saturates the connection and essentially stops any other traffic until the upload is finished. Looking at the manual, it looks like it should do this, but does not seem clear to me.
View 1 Replies View RelatedSo my ISP (Telus) recently replaced our old router with a ZyXEL VSG1432. I'm currently having a huge lag issue when my roommates laptop is connected to our network. He is connected via wireless, I'm wired. So I did some searching around and I think i can solve this by limiting his bandwidth with QoS settings. I'm getting conflicting information here though. After logging into the router there are no QoS options yet according to ZyXEL's website url...This router should have the settings available. Is it possible that Telus does something to remove this feature? Is there some not so obvious way to enable QoS? Is there some other way to limit the bandwidth?
View 1 Replies View RelatedI currently use Verizon FiOS 20/5. The speed has been great until the day my cousin and his parents moved in. They also use our FiOS connection and I have came to the conclusion that my cousin's laptop is eating away all of the bandwidth which makes all devices using FiOS have extremely slow internet speeds. I know it is his computer because I logged in as admin to the Verizon FiOS page (192.168.1.1) and I saw that he is using several P2P applications and downloading torrents as well. Is there a way I can limit the bandwidth he is using so that the internet speed can improve? I looked at the QoS tab and tried to play around with the settings, but I don't want to mess it up. The router I have is Actiontec M1424-WR (Verizon FiOS 20 Down/5 Up). A lot of sources I am reading says that I have to use the QoS, but I don't know how to use it on the site.
View 3 Replies View RelatedI will have this one router. Its f0/0 will be for the Internet connection with bandwidth of 30Mbps. Its f0/1 will be connected to a switch for internal networks. This link will be separated to 3 VLANs for 3 internal networks. I'm wondering if there is a way to gurantee 10Mbps for each VLAN but allow use up to 30Mbps when another two VLANs are not using any Internet bandwidth? I only worry about download bandwidth from internet.The 3 internal networks will all have public IPs and they belong to their own subnets. There won't be NAT/PAT.
View 18 Replies View RelatedWe have a new 100MB internet service, but we only pay for 10MB and above that is a per/MB fee and not cheap. I want to limit all traffic inbound and outbound only to use up to 10MB on the outside interface of our Cisco 3825.
View 9 Replies View Relatedhow i can limit the bandwidth for a all my client conect to the AP, i have a Aironet 1200 with the 12.2.15 code.
View 3 Replies View RelatedI have a 4500 and 6500 that I'd like to be able to limit the bandwidth of layer 2 switchports. So for instance I have all GB blades but certain servers I'd like only to have connections of about 5 Mb per second or 15 Mb per second etc.
View 1 Replies View RelatedMy QA team needs to test number of special connectivity scenarios where their wireless connection has a limited bandwidth.Ideally, I would like to provide them number of SSIDs each of which has different bandwidth limitation.But so far I did not find a way to apply any bandwidth limitations to my 2504 Wireless controller and the 3602E AP.QoS has only 4 pre-defined modes which can't be set to a specific limit.
View 10 Replies View RelatedI 3750 doesn't support "shape" command under policy map. How do I limit the bandwidth to 3 M? [code]
View 3 Replies View RelatedCan I limit bandwith for guest in a wlan network with out Wlan controller? and of course, how can I do it?P.S.: I heard something about bronze profile in a wlan controller envoiroment, I need something like that but in an independent AP.
View 3 Replies View RelatedAny idea for limiting bandwidth on cisco 892F router? We have 2 VLANs through our LAN and one must be limited upto 1Mbps or 512Kbps.
View 2 Replies View RelatedHow do I setup this on the SRP527W? I already block most of the video stuff on the internet. But I want to make this one more step.
View 1 Replies View RelatedHow do I setup one IP to throttle bandwidth?
View 1 Replies View RelatedI came across some free bandwidth monitoring software by Solarwinds while doing some reading on other sites. I installed the software and now im stuck at setup. The Softaware is asking for...
Ip Address/Hostname
SNMP Version
Community string
I'm assuming the IP Address/Hostname would be my computers IPv4 on the network and as far as the SNMP Version goes im not sure, I can either choose from SNMP v1/2c or v3. For the community string, I'm assuming its Public but im not completely sure.When I attempt to go to the next step is says the credentials test failed So obviously something I entered is incorrect.
Note: this is on my own home network. Im using a Comcast all in one router and modem.
I got connected ASA ----- ROUTER 2811) to metroethernet switch from my ISP , with a 4MB of bandwidth but the internet connections to all my LAN has been frozen and we lost connection to the internet, to restart the internet service I need to boot the ROUTER 2811 - and ISP switch to rollback the internet operation,My ISP support tell me if is possible to set up the traffic bandwidth in one or both borders devices, ( ASA 5510 or ROUTER 2811)
View 3 Replies View RelatedI am trying to set up my router to grant http traffic a minimum bandwidth of - for example - 5,000 kBit (if there is any http traffic).
So I set http min. rate to 5,000 while I set nntp min. rate to 1 However, when I run nntp downloads on several connections (e.g. 10) my single http download never goes above 1,000 kBit. Without any other connections I reach 8,000 kBit.
I am using a single 12 MBit line.
Region : UnitedKingdom
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP :
Looking at the manual for this router in regards to bandwidth restrictions.When you set up the Rules under Bandwidth Control does this setting shared by the IP range or does each IP in the range get that amount of bandwidth?
I have a Cisco Aironet 1240AG Access Point and I am trying to setup a guest network that is secure and limited in bandwidth utilization. I see an option under security > SSID Manager on the web interface to select an interface of Radio0-802.11G, Radio1-802.11A or both. Can I put the guest network on the Radio1-802.11A and make it more secure/bandwidth limited or does this option not matter?
View 3 Replies View RelatedWe have 1 mpbs bandwidth line, but most of the time we are getting only 300-500 kpbs download speed, i want to send statistics report to our ISP, what will be best procedure to test the bandwidth report, i have checked in some websites like bandwidthplace and speedtest but these sites are not accurate, how to check the actual bandwidth we getting from ISP against 1 Mbps. We have solarwinds monitoring tool in this i have configured the WAN interface for 1 mbps
View 5 Replies View RelatedI have a 3825 with a 16 port etherswitch card installed that I'm trying to setup rate-limits on. Interface G0/0 is the connection to the outside world and int g0/1 has a couple of 2950 switches attached to it.
The etherswitch card, f1/0, f1,1 etc has corresponding vlans, 902, 903 etc each with an IP 10.110.1.x, 10.110.2.x and all part of access-group 111. The switches connect on sub-interfaces g0/1.101, g0/1.102 etc and have IP's 10.55.1.x, 10.55.2.x and part of access-group 101.
What i'm trying to achieve is that every port / IP that is on access-group 111 shares 3Mb of bandwidth in/out and access-group 101 shares a separate 3Mb of bandwidth in/out.
I've created two access-lists as follows;
access-list 101 permit ip 10.55.0.0 0.0.255.255 any
access-list 111 permit ip 10.110.0.0 0.0.255.255 any
And on int g0/0 I've created the following rate-limits;
rate-limit input access-group 101 3072000 64000 64000 conform-action transmit exceed-action drop
rate-limit input access-group 111 3072000 64000 64000 conform-action transmit exceed-action drop
rate-limit output access-group 101 3072000 64000 64000 conform-action transmit exceed-action drop
rate-limit output access-group 111 3072000 64000 64000 conform-action transmit exceed-action drop
Now instead of both access-groups having 3Mb each they all seem to be sharing 3Mb! I've tried class-maps and policy-maps but to no avail..
I've had a DIR-600 for years, and this past month it has been really bad. I have a 3mbps Cable connection, always worked fine and fast, but since the start of the month I've been getting, at most, 60kb/s of download speed (I have a wired connection to the router). Speed tests register everything as fine, except for the download speed, which is really unstable and shoots all over the place, going from 1MB/s to 0 in some instances. I thought it was the ISP being bad since we're having a lot of problems with this provider where I work, but got tired of it and decided to do some troubleshooting myself. When I connect directly to the modem, without the router, I get the same fast speeds I used to. I tried rebooting everything, I tried resetting the router to factory defaults, but nothing seemed to change that. DL speed is always below 60KB/s and if something is downloading at that speed, a single page takes a minute to load.
View 3 Replies View RelatedI need to limit the amount of data my child can download each day and can't find a simple program to do this. I have a Verizon MiFi access point in my house with a 10GB monthly cap. I need a program that I can install on a single computer that will allow say, 100MB per day data transfer, then not allow any more internet access on that computer till the next day. I'm OK with computers, but not a guru so simplicity of setup & use is important.Most programs I've seen are geared for complex network monitoring by IT pros, and the ones geared for monitoring kids mainly restrict access by time spent online, whereas I need to cap usage by the amount used each day. Computer is an Acer laptop and an eMachines desktop, both using wireless access and both running Windows 7.
View 7 Replies View RelatedI have a router 3845 connected to a LAN and other routers and providing internet through a link on an ethernet interface
Gi0/0
LAN connection
GI0/1
WAN connection
fa0/0
Internet connection
I am looking for information on how to properly configure rate limits on a Cisco 2821 so that I can set different Service levels by IP address. For example I want to limit a block of IPs to 1 Mbps Down and 512 kbps Up. I am doing point to point networks from our router (ISR 2821) to another router that is assigned a static IP. The other router connects to our router through a Fast Ethernet port on a NM 16 port switch card. The routing end point for the network is on a VLAN interface. Currently we are using bonded T1's but are about to turn up a Metro-E circuit.
View 1 Replies View RelatedIs there a way to limit number of concurrent SSH connections that Prime LMS 4.2 makes to devices? Periodically it occupies all of VTY lines. I know I can restrict access to particular VTY lines by 'access-class' command, but I'd rather want to limit number of simultaneous connections on Prime LMS. Is it possible?
View 2 Replies View Related
