Cisco WAN :: Rate Limiting By IP On 2821 ISR?
Nov 8, 2011
I am looking for information on how to properly configure rate limits on a Cisco 2821 so that I can set different Service levels by IP address. For example I want to limit a block of IPs to 1 Mbps Down and 512 kbps Up. I am doing point to point networks from our router (ISR 2821) to another router that is assigned a static IP. The other router connects to our router through a Fast Ethernet port on a NM 16 port switch card. The routing end point for the network is on a VLAN interface. Currently we are using bonded T1's but are about to turn up a Metro-E circuit.
View 1 Replies
ADVERTISEMENT
Feb 24, 2011
I have a 3825 with a 16 port etherswitch card installed that I'm trying to setup rate-limits on. Interface G0/0 is the connection to the outside world and int g0/1 has a couple of 2950 switches attached to it.
The etherswitch card, f1/0, f1,1 etc has corresponding vlans, 902, 903 etc each with an IP 10.110.1.x, 10.110.2.x and all part of access-group 111. The switches connect on sub-interfaces g0/1.101, g0/1.102 etc and have IP's 10.55.1.x, 10.55.2.x and part of access-group 101.
What i'm trying to achieve is that every port / IP that is on access-group 111 shares 3Mb of bandwidth in/out and access-group 101 shares a separate 3Mb of bandwidth in/out.
I've created two access-lists as follows;
access-list 101 permit ip 10.55.0.0 0.0.255.255 any
access-list 111 permit ip 10.110.0.0 0.0.255.255 any
And on int g0/0 I've created the following rate-limits;
rate-limit input access-group 101 3072000 64000 64000 conform-action transmit exceed-action drop
rate-limit input access-group 111 3072000 64000 64000 conform-action transmit exceed-action drop
rate-limit output access-group 101 3072000 64000 64000 conform-action transmit exceed-action drop
rate-limit output access-group 111 3072000 64000 64000 conform-action transmit exceed-action drop
Now instead of both access-groups having 3Mb each they all seem to be sharing 3Mb! I've tried class-maps and policy-maps but to no avail..
View 3 Replies
View Related
Aug 18, 2011
I have a router 3845 connected to a LAN and other routers and providing internet through a link on an ethernet interface
Gi0/0
LAN connection
GI0/1
WAN connection
fa0/0
Internet connection
View 9 Replies
View Related
Feb 10, 2011
I have used the following basic configuration to do rate limiting on a vlan interface on a 6509:
access-list 100 permit ip any any
class-map match-all ratelimit
match access-group 100
policy-map ratelimit-10Mb
class ratelimit
police 10000000 428750 conform-action transmit exceed-action drop
[code]....
How do I combine the two correctly to give me a vlan port rate limited at 10Mb up and down, but still setting aside (dynamically) 2Mb for voice?
View 1 Replies
View Related
Jul 17, 2012
We have a guest wireless setup but I need to rate limit the users so no one hogs all the bandwidth. The WLC is connected into a 3750 which is doing all the routing between the vlans. I know I cannot shape the traffic on the 3750.
View 2 Replies
View Related
Nov 14, 2011
I have a 2960 that I need to limit the uplink port to 50Mbps for 3 vlans and 350Mbps for another vlan. Would the following config achieve that or is this even possible for the 2960?
class-map match-any VLAN50-51-52
match vlan 50-52
class-map match-any VLAN53
[Code].....
View 1 Replies
View Related
Jul 18, 2011
i have to restrict that router and switches shall join only given multicasts. Means if i change multicast in TVG430 from 239.0.96.1 to 233.0.96.1 than it shall be blocked.My TX rate i set to 20 Mbits on TVG430, i want to rate-limit it to 15 Mbits on switch on Ingress int gi 0/23 or egress gi 0/24 included are three show runs output.ip multicast rate-limit out group-list GROUP source-list SOURCE.
View 2 Replies
View Related
Oct 30, 2011
I am trying to limit traffic inbound to 10Mbps on a gig interface 0/48 set to 100/full. So I downloaded some big files over this link and I'm able to see 30- 40Mbps or more. You can see from the show int - rate-limit command that parameters are never showing exceented so nothing has been dropped. [code]
View 3 Replies
View Related
Feb 5, 2012
I'm trying to limit the bandwidth on certain ports to 3Mbps and others 1Mbps for a project, however when I do a bandwidth test from a website the speed on the router doesn't seem to change it's as if the changes over telnet aren't actually affecting the swtich's qos settings. I have verified that the policy is attached to the interface and the settings are correct as well.
Router
Telnet address: 10.xxx.xx.xx
Password:
[Code].....
View 1 Replies
View Related
Sep 11, 2012
We have a number of 6509s which generally have dhcp relay agents configured on the SVIs. The dhcp servers are centralised. Recently we've had one or two faults with misconfigured or faulty devices (blade server chassis and also printers) generating high volumes of dhcp discover packets and causing high cpu on the relevant 6500. I would like to rate limit these discover packets, which are layer 2 broadcasts. Storm control can't discriminate between different types of broadcasts and on a gig link would need to be set down at about 1% to have much effect on the problem. I've looked at CoPP and also mls hardware rate-limiting but as I understand it, these two features don't control broadcast traffic. I also looked at dhcp snooping but if an interface receives a high level of dhcp discover broadcasts, e.g. over 100pps, I don't want it to go error-disabled (as this would knock down the whole edge switch), just to drop the excess packets.
View 2 Replies
View Related
Mar 27, 2012
how to perform UBRL User Based Rate Limiting on ASR1000 like we can do it on Catalyst6500?
View 3 Replies
View Related
Dec 11, 2010
We have cisoc 2821 at one of branch and created five sub inetrfaces for different vlans.Output of Show interface shows very frequent increase in the input error count.I have changed the physical cable and switch port on the other side.But still error rate is increasing.When the traffic is less error rate is low but with high traffic it is increasing drastically.My router process is very less(4%) only.What could be possible reason. [code]
View 8 Replies
View Related
May 20, 2012
Is there a way to limit number of concurrent SSH connections that Prime LMS 4.2 makes to devices? Periodically it occupies all of VTY lines. I know I can restrict access to particular VTY lines by 'access-class' command, but I'd rather want to limit number of simultaneous connections on Prime LMS. Is it possible?
View 2 Replies
View Related
Apr 7, 2011
I live in rural Alaska and use satellite internet with 1.5mbps rate and 4gb rolling weekly download limit. I was wondering if there are any wireless routers I can buy that I can set a bandwidth limit for the specific router. Due to teenage girls in the house we hit the weekly limit in a day or two because of all the music videos and such that they watch on you tube, it is annoying getting limited to the 256kbps download rate so often.
View 5 Replies
View Related
Mar 13, 2012
I am a gamer living in my apartment with a room mate who loves to download music 24/7 and a girlfriend who loves to watch netflix. Needless to say, every time I go to play a video game I get shitty ping and lots of lag. From what I've gathered, DD-WRT's QOS is ****, and Tomato is the way to go in 3rd party firmware.
View 1 Replies
View Related
Feb 13, 2012
Is it possible to set up an RV110W to limit access to only specified websites according to a schedule? I can block access to specific sites using the Internet Access Policy settings under Firewall, but I can't figure out a successful way to block access to all sites except those specified. I also tried establishing access rules but that did not work either.
View 4 Replies
View Related
Jun 10, 2013
We have two Cisco 2811 Routers setup with a GRE tunnel that we would like to constrain the bandwidth on to replicate a satellite connectinon of 400 kbits. We tried the bandwidth command 400, but from what I understand that is only for routing metrics and not actual speed of the interface.
View 5 Replies
View Related
Apr 13, 2011
I have a SG 300-20 small business switch and I would like to restrict bandwidth by gateway ip address but not by physical port or LAG. On the web interface, I can only do bw limiting per port or lag. I want to do bandwidth limiting by the IP addresses that I assign to vlans that my hosts use as a gateway ip.
View 3 Replies
View Related
Feb 6, 2012
I have a Cisco ASA5510 with two Cisco Catalyst 3560G switches plugged into it. Then I have 2 Cisco1400 Aironet WAPs plugged into the switches.
My goal is to limit incoming bandwith for two specific vlans. So users who are plugged into the switch or connected to the wifi can't go bandwidth crazy.
The rule I currently have setup on the ASA5510 is limiting internal bandwidth, I know shame on me.
So how do I setup a rule on the ASA5510 that will limit users external traffic on vlans without limit internal lan traffic?
View 5 Replies
View Related
Jun 4, 2013
I have an RV220W which I would like to set bandwidth limiting on. When we upload files to yousendit or an FTP server, it saturates the connection and essentially stops any other traffic until the upload is finished. Looking at the manual, it looks like it should do this, but does not seem clear to me.
View 1 Replies
View Related
Feb 21, 2012
I've had a DIR-600 for years, and this past month it has been really bad. I have a 3mbps Cable connection, always worked fine and fast, but since the start of the month I've been getting, at most, 60kb/s of download speed (I have a wired connection to the router). Speed tests register everything as fine, except for the download speed, which is really unstable and shoots all over the place, going from 1MB/s to 0 in some instances. I thought it was the ISP being bad since we're having a lot of problems with this provider where I work, but got tired of it and decided to do some troubleshooting myself. When I connect directly to the modem, without the router, I get the same fast speeds I used to. I tried rebooting everything, I tried resetting the router to factory defaults, but nothing seemed to change that. DL speed is always below 60KB/s and if something is downloading at that speed, a single page takes a minute to load.
View 3 Replies
View Related
Jun 11, 2011
Without using another box as a router preferably. My Cisco Linksys router doesn't have any options for this but I heard you could possibly install some 3rd party firmware to get around that. This would be a last resort for me What I'm hoping for his some piece of software that could do this
View 2 Replies
View Related
Jan 2, 2011
I need to limit the amount of data my child can download each day and can't find a simple program to do this. I have a Verizon MiFi access point in my house with a 10GB monthly cap. I need a program that I can install on a single computer that will allow say, 100MB per day data transfer, then not allow any more internet access on that computer till the next day. I'm OK with computers, but not a guru so simplicity of setup & use is important.Most programs I've seen are geared for complex network monitoring by IT pros, and the ones geared for monitoring kids mainly restrict access by time spent online, whereas I need to cap usage by the amount used each day. Computer is an Acer laptop and an eMachines desktop, both using wireless access and both running Windows 7.
View 7 Replies
View Related
Jan 14, 2013
Network settings. What I want to do is limit the rate that people can download files from my webserver remotely. LAN connections should still be able to transfer at full speed, but anything outside of the local network should be limited to 200Kbps per connection. Is that even possible? Can I limit the number of connections per client (probably by IP)?
If this can't be done at the OS level, is there any way I could script it using PHP? Maybe read X bytes into a file and then sleep...
View 1 Replies
View Related
Jul 29, 2010
I will have this one router. Its f0/0 will be for the Internet connection with bandwidth of 30Mbps. Its f0/1 will be connected to a switch for internal networks. This link will be separated to 3 VLANs for 3 internal networks. I'm wondering if there is a way to gurantee 10Mbps for each VLAN but allow use up to 30Mbps when another two VLANs are not using any Internet bandwidth? I only worry about download bandwidth from internet.The 3 internal networks will all have public IPs and they belong to their own subnets. There won't be NAT/PAT.
View 18 Replies
View Related
Mar 13, 2012
We have a new 100MB internet service, but we only pay for 10MB and above that is a per/MB fee and not cheap. I want to limit all traffic inbound and outbound only to use up to 10MB on the outside interface of our Cisco 3825.
View 9 Replies
View Related
May 17, 2004
how i can limit the bandwidth for a all my client conect to the AP, i have a Aironet 1200 with the 12.2.15 code.
View 3 Replies
View Related
Apr 16, 2012
I have a 4500 and 6500 that I'd like to be able to limit the bandwidth of layer 2 switchports. So for instance I have all GB blades but certain servers I'd like only to have connections of about 5 Mb per second or 15 Mb per second etc.
View 1 Replies
View Related
Jan 27, 2011
I have three VLANS set up on my Catalyst 3560G switch. Each VLAN has its own subnet and I have enabled IP routing and set up my VLANS so that clients on VLANS 1 and 3 can get to VLAN 2 because they share a server located on VLAN 2. However, now they can also see and get to each others VLANS! How I can allow my clients on VLANS 1 and 3 access a server on VLAN 2 but not access the other VLANS? I don't want VLAN 1 to get to VLAN 3 or VLAN 3 to get to VLAN 1.
View 17 Replies
View Related
Aug 20, 2012
I run a business and have customers who would like to use my wireless internet. I previously had a completely open network that I would allow them to use, until someone illegally downloaded a movie and got us in trouble. I would like to allow use of the network again, but limit activities like this. Basically, so they could only do basic web browsing, etc.
View 1 Replies
View Related
Sep 19, 2012
how to limit bandwidth only for user account in window 7...My PC has 2 account ..one is admin and other is user ..i need to limit the bandwidth only for user account ,do I need a software for this.
View 3 Replies
View Related
Feb 23, 2012
I am sutdying at uni and in a few months, I will be moving into a house, with my current flatmates. We will be buying a fibre optic line.Ideally,what I want to do, is split the connections evenly,depending on how many people are online current, rather than having mass downloads of everyone at the same time, when other will only get a small speed while browsing or gaming,or streaming,etc.So, basically, what I want to do is split the connection at anyone time evenly,so if there are 5 people connected and our connection speed is 50MB then each will get 10MB. And if 2 people are connected, then the speed will be 25MB each, and so on.
I am wondering what is the cheapest way of doing this? I am very computer illerate,I know how to use unix systems.I even own my own server, but I'm not so clued up in this area of networking.I believe it's something to do with a switch, and which switches support this? (I've heard it's something to do with full-duplex / half duplex).
- I will probably set up a domain system, where everyone has to login to the main server to access the internet. (I know vaguely how to do that) - is there some software that I can put on the server which will distribute connection speeds automatically.
View 6 Replies
View Related
Apr 13, 2011
Is it possable to limit the download/upload speeds of a wireless computer on this router, the reason is i am at home working on files from my office computer and my son gets home, and starts downloading massive amounts of music an other ****, and i get disconnected to the office computer, and have to start from scratch again. I just want to limit his speed to maybe 25% of the max internet connection.
View 5 Replies
View Related
