I have a 4500 and 6500 that I'd like to be able to limit the bandwidth of layer 2 switchports. So for instance I have all GB blades but certain servers I'd like only to have connections of about 5 Mb per second or 15 Mb per second etc.
View 1 RepliesI 3750 doesn't support "shape" command under policy map. How do I limit the bandwidth to 3 M? [code]
View 3 Replies View RelatedAny idea for limiting bandwidth on cisco 892F router? We have 2 VLANs through our LAN and one must be limited upto 1Mbps or 512Kbps.
View 2 Replies View RelatedAs per my understanding 6509 all slots are dual channel, so 9 slot * 40 per slot (20 g in and 20 g out) = 360 GB How cisco claim the 720 ?? What about the 6513 chassic switch fabric connection?
View 5 Replies View RelatedI live in rural Alaska and use satellite internet with 1.5mbps rate and 4gb rolling weekly download limit. I was wondering if there are any wireless routers I can buy that I can set a bandwidth limit for the specific router. Due to teenage girls in the house we hit the weekly limit in a day or two because of all the music videos and such that they watch on you tube, it is annoying getting limited to the 256kbps download rate so often.
View 5 Replies View RelatedI am a gamer living in my apartment with a room mate who loves to download music 24/7 and a girlfriend who loves to watch netflix. Needless to say, every time I go to play a video game I get shitty ping and lots of lag. From what I've gathered, DD-WRT's QOS is ****, and Tomato is the way to go in 3rd party firmware.
View 1 Replies View RelatedWithout using another box as a router preferably. My Cisco Linksys router doesn't have any options for this but I heard you could possibly install some 3rd party firmware to get around that. This would be a last resort for me What I'm hoping for his some piece of software that could do this
View 2 Replies View RelatedWe have two Cisco 2811 Routers setup with a GRE tunnel that we would like to constrain the bandwidth on to replicate a satellite connectinon of 400 kbits. We tried the bandwidth command 400, but from what I understand that is only for routing metrics and not actual speed of the interface.
View 5 Replies View RelatedI have a SG 300-20 small business switch and I would like to restrict bandwidth by gateway ip address but not by physical port or LAG. On the web interface, I can only do bw limiting per port or lag. I want to do bandwidth limiting by the IP addresses that I assign to vlans that my hosts use as a gateway ip.
View 3 Replies View RelatedI have a Cisco ASA5510 with two Cisco Catalyst 3560G switches plugged into it. Then I have 2 Cisco1400 Aironet WAPs plugged into the switches.
My goal is to limit incoming bandwith for two specific vlans. So users who are plugged into the switch or connected to the wifi can't go bandwidth crazy.
The rule I currently have setup on the ASA5510 is limiting internal bandwidth, I know shame on me.
So how do I setup a rule on the ASA5510 that will limit users external traffic on vlans without limit internal lan traffic?
I have an RV220W which I would like to set bandwidth limiting on. When we upload files to yousendit or an FTP server, it saturates the connection and essentially stops any other traffic until the upload is finished. Looking at the manual, it looks like it should do this, but does not seem clear to me.
View 1 Replies View RelatedI run a business and have customers who would like to use my wireless internet. I previously had a completely open network that I would allow them to use, until someone illegally downloaded a movie and got us in trouble. I would like to allow use of the network again, but limit activities like this. Basically, so they could only do basic web browsing, etc.
View 1 Replies View Relatedhow to limit bandwidth only for user account in window 7...My PC has 2 account ..one is admin and other is user ..i need to limit the bandwidth only for user account ,do I need a software for this.
View 3 Replies View RelatedI will have this one router. Its f0/0 will be for the Internet connection with bandwidth of 30Mbps. Its f0/1 will be connected to a switch for internal networks. This link will be separated to 3 VLANs for 3 internal networks. I'm wondering if there is a way to gurantee 10Mbps for each VLAN but allow use up to 30Mbps when another two VLANs are not using any Internet bandwidth? I only worry about download bandwidth from internet.The 3 internal networks will all have public IPs and they belong to their own subnets. There won't be NAT/PAT.
View 18 Replies View RelatedWe have a new 100MB internet service, but we only pay for 10MB and above that is a per/MB fee and not cheap. I want to limit all traffic inbound and outbound only to use up to 10MB on the outside interface of our Cisco 3825.
View 9 Replies View Relatedhow i can limit the bandwidth for a all my client conect to the AP, i have a Aironet 1200 with the 12.2.15 code.
View 3 Replies View RelatedSo my ISP (Telus) recently replaced our old router with a ZyXEL VSG1432. I'm currently having a huge lag issue when my roommates laptop is connected to our network. He is connected via wireless, I'm wired. So I did some searching around and I think i can solve this by limiting his bandwidth with QoS settings. I'm getting conflicting information here though. After logging into the router there are no QoS options yet according to ZyXEL's website url...This router should have the settings available. Is it possible that Telus does something to remove this feature? Is there some not so obvious way to enable QoS? Is there some other way to limit the bandwidth?
View 1 Replies View RelatedI currently use Verizon FiOS 20/5. The speed has been great until the day my cousin and his parents moved in. They also use our FiOS connection and I have came to the conclusion that my cousin's laptop is eating away all of the bandwidth which makes all devices using FiOS have extremely slow internet speeds. I know it is his computer because I logged in as admin to the Verizon FiOS page (192.168.1.1) and I saw that he is using several P2P applications and downloading torrents as well. Is there a way I can limit the bandwidth he is using so that the internet speed can improve? I looked at the QoS tab and tried to play around with the settings, but I don't want to mess it up. The router I have is Actiontec M1424-WR (Verizon FiOS 20 Down/5 Up). A lot of sources I am reading says that I have to use the QoS, but I don't know how to use it on the site.
View 3 Replies View RelatedMy QA team needs to test number of special connectivity scenarios where their wireless connection has a limited bandwidth.Ideally, I would like to provide them number of SSIDs each of which has different bandwidth limitation.But so far I did not find a way to apply any bandwidth limitations to my 2504 Wireless controller and the 3602E AP.QoS has only 4 pre-defined modes which can't be set to a specific limit.
View 10 Replies View RelatedCan I limit bandwith for guest in a wlan network with out Wlan controller? and of course, how can I do it?P.S.: I heard something about bronze profile in a wlan controller envoiroment, I need something like that but in an independent AP.
View 3 Replies View RelatedHow do I setup this on the SRP527W? I already block most of the video stuff on the internet. But I want to make this one more step.
View 1 Replies View Relatedhow can we upgrade 6500 non modular ios to normal 6500 ios?
View 5 Replies View RelatedWe recently got a 1921 for our main office and we have a dedicated 15/15 connection. We're running on an 1871 right now that is not under my control so I can't even see it's running config. OK! So when I set my gateway to be the 1871, we can get our upload to over 6mbit (we have 8 branches, so won't ever get full 15 since they're using it too). With the gateway set as the 1921, it seems like we're stuck at 1.5. I haven't seen it go higher than that. I've looked over the config but can't see anything that would imply some kind of bandwidth limit but I have copied the config here.
Building configuration...
Current configuration : 6688 bytes
!
! Last configuration change at 10:59:47 PCTime Thu Nov 29 2012 by admin
! NVRAM config last updated at 10:04:31 PCTime Thu Nov 29 2012 by admin
! NVRAM config last updated at 10:04:31 PCTime Thu Nov 29 2012 by admin
version 15.1
[code]....
We have a guest wireless setup but I need to rate limit the users so no one hogs all the bandwidth. The WLC is connected into a 3750 which is doing all the routing between the vlans. I know I cannot shape the traffic on the 3750.
View 2 Replies View RelatedI have a 2960 that I need to limit the uplink port to 50Mbps for 3 vlans and 350Mbps for another vlan. Would the following config achieve that or is this even possible for the 2960?
class-map match-any VLAN50-51-52
match vlan 50-52
class-map match-any VLAN53
[Code].....
I have a 3560 switch where I have 4 ports connected, one is to our WAN provider - 10Mbps and the other three are connected to different customers who I want to get an equal share of the 10Mbps bandwidth.I'm fairly clued up about configuring modular QoS but I'm being thrown by the fact that you can't apply a service-policy outbound on the ethernet ports.
View 3 Replies View RelatedI am trying to limit traffic inbound to 10Mbps on a gig interface 0/48 set to 100/full. So I downloaded some big files over this link and I'm able to see 30- 40Mbps or more. You can see from the show int - rate-limit command that parameters are never showing exceented so nothing has been dropped. [code]
View 3 Replies View RelatedI'm trying to limit the bandwidth on certain ports to 3Mbps and others 1Mbps for a project, however when I do a bandwidth test from a website the speed on the router doesn't seem to change it's as if the changes over telnet aren't actually affecting the swtich's qos settings. I have verified that the policy is attached to the interface and the settings are correct as well.
Router
Telnet address: 10.xxx.xx.xx
Password:
[Code].....
We have a number of 6509s which generally have dhcp relay agents configured on the SVIs. The dhcp servers are centralised. Recently we've had one or two faults with misconfigured or faulty devices (blade server chassis and also printers) generating high volumes of dhcp discover packets and causing high cpu on the relevant 6500. I would like to rate limit these discover packets, which are layer 2 broadcasts. Storm control can't discriminate between different types of broadcasts and on a gig link would need to be set down at about 1% to have much effect on the problem. I've looked at CoPP and also mls hardware rate-limiting but as I understand it, these two features don't control broadcast traffic. I also looked at dhcp snooping but if an interface receives a high level of dhcp discover broadcasts, e.g. over 100pps, I don't want it to go error-disabled (as this would knock down the whole edge switch), just to drop the excess packets.
View 2 Replies View RelatedI am trying to limit the incoming and outgoing traffic on a l2 port to 8mbps for a ip subnet within the nexus 7000. The port is connected to my ISP router which has a bandwidth of 20mbps.Policing won't work on a l2 Port and shaping cannot be applied on a port level. url...I have been reading thru the qos guide for nexus release v6 and have problems understanding the different queues.
View 3 Replies View Relatedhow to perform UBRL User Based Rate Limiting on ASR1000 like we can do it on Catalyst6500?
View 3 Replies View RelatedI am seeing a strange situation on my 6500 switch?By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for switching processor is gone to 88 % and some time creeps to 99 %.
snmpwalk -v2c -c "removes" sw6500 '1.3.6.1.4.1.9.9.109.1.1.1.1.3'
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.1 = Gauge32: 12 (--- this is for CPU of Router Processor )
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.3 = Gauge32: 99 (--- this is for CPU of Switching Processor )
but when I do sh process cpu on the console, all looks normal as it shows cpu utilization of RP. why the value is so high on the switching processor ?
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?
View 1 Replies View Related