We have two Cisco 2811 Routers setup with a GRE tunnel that we would like to constrain the bandwidth on to replicate a satellite connectinon of 400 kbits. We tried the bandwidth command 400, but from what I understand that is only for routing metrics and not actual speed of the interface.
View 5 RepliesI live in rural Alaska and use satellite internet with 1.5mbps rate and 4gb rolling weekly download limit. I was wondering if there are any wireless routers I can buy that I can set a bandwidth limit for the specific router. Due to teenage girls in the house we hit the weekly limit in a day or two because of all the music videos and such that they watch on you tube, it is annoying getting limited to the 256kbps download rate so often.
View 5 Replies View RelatedI am a gamer living in my apartment with a room mate who loves to download music 24/7 and a girlfriend who loves to watch netflix. Needless to say, every time I go to play a video game I get shitty ping and lots of lag. From what I've gathered, DD-WRT's QOS is ****, and Tomato is the way to go in 3rd party firmware.
View 1 Replies View RelatedWithout using another box as a router preferably. My Cisco Linksys router doesn't have any options for this but I heard you could possibly install some 3rd party firmware to get around that. This would be a last resort for me What I'm hoping for his some piece of software that could do this
View 2 Replies View RelatedI have a SG 300-20 small business switch and I would like to restrict bandwidth by gateway ip address but not by physical port or LAG. On the web interface, I can only do bw limiting per port or lag. I want to do bandwidth limiting by the IP addresses that I assign to vlans that my hosts use as a gateway ip.
View 3 Replies View RelatedI have a Cisco ASA5510 with two Cisco Catalyst 3560G switches plugged into it. Then I have 2 Cisco1400 Aironet WAPs plugged into the switches.
My goal is to limit incoming bandwith for two specific vlans. So users who are plugged into the switch or connected to the wifi can't go bandwidth crazy.
The rule I currently have setup on the ASA5510 is limiting internal bandwidth, I know shame on me.
So how do I setup a rule on the ASA5510 that will limit users external traffic on vlans without limit internal lan traffic?
I have an RV220W which I would like to set bandwidth limiting on. When we upload files to yousendit or an FTP server, it saturates the connection and essentially stops any other traffic until the upload is finished. Looking at the manual, it looks like it should do this, but does not seem clear to me.
View 1 Replies View RelatedI run a business and have customers who would like to use my wireless internet. I previously had a completely open network that I would allow them to use, until someone illegally downloaded a movie and got us in trouble. I would like to allow use of the network again, but limit activities like this. Basically, so they could only do basic web browsing, etc.
View 1 Replies View Relatedhow to limit bandwidth only for user account in window 7...My PC has 2 account ..one is admin and other is user ..i need to limit the bandwidth only for user account ,do I need a software for this.
View 3 Replies View RelatedI will have this one router. Its f0/0 will be for the Internet connection with bandwidth of 30Mbps. Its f0/1 will be connected to a switch for internal networks. This link will be separated to 3 VLANs for 3 internal networks. I'm wondering if there is a way to gurantee 10Mbps for each VLAN but allow use up to 30Mbps when another two VLANs are not using any Internet bandwidth? I only worry about download bandwidth from internet.The 3 internal networks will all have public IPs and they belong to their own subnets. There won't be NAT/PAT.
View 18 Replies View RelatedWe have a new 100MB internet service, but we only pay for 10MB and above that is a per/MB fee and not cheap. I want to limit all traffic inbound and outbound only to use up to 10MB on the outside interface of our Cisco 3825.
View 9 Replies View Relatedhow i can limit the bandwidth for a all my client conect to the AP, i have a Aironet 1200 with the 12.2.15 code.
View 3 Replies View RelatedI have a 4500 and 6500 that I'd like to be able to limit the bandwidth of layer 2 switchports. So for instance I have all GB blades but certain servers I'd like only to have connections of about 5 Mb per second or 15 Mb per second etc.
View 1 Replies View RelatedSo my ISP (Telus) recently replaced our old router with a ZyXEL VSG1432. I'm currently having a huge lag issue when my roommates laptop is connected to our network. He is connected via wireless, I'm wired. So I did some searching around and I think i can solve this by limiting his bandwidth with QoS settings. I'm getting conflicting information here though. After logging into the router there are no QoS options yet according to ZyXEL's website url...This router should have the settings available. Is it possible that Telus does something to remove this feature? Is there some not so obvious way to enable QoS? Is there some other way to limit the bandwidth?
View 1 Replies View RelatedI currently use Verizon FiOS 20/5. The speed has been great until the day my cousin and his parents moved in. They also use our FiOS connection and I have came to the conclusion that my cousin's laptop is eating away all of the bandwidth which makes all devices using FiOS have extremely slow internet speeds. I know it is his computer because I logged in as admin to the Verizon FiOS page (192.168.1.1) and I saw that he is using several P2P applications and downloading torrents as well. Is there a way I can limit the bandwidth he is using so that the internet speed can improve? I looked at the QoS tab and tried to play around with the settings, but I don't want to mess it up. The router I have is Actiontec M1424-WR (Verizon FiOS 20 Down/5 Up). A lot of sources I am reading says that I have to use the QoS, but I don't know how to use it on the site.
View 3 Replies View RelatedMy QA team needs to test number of special connectivity scenarios where their wireless connection has a limited bandwidth.Ideally, I would like to provide them number of SSIDs each of which has different bandwidth limitation.But so far I did not find a way to apply any bandwidth limitations to my 2504 Wireless controller and the 3602E AP.QoS has only 4 pre-defined modes which can't be set to a specific limit.
View 10 Replies View RelatedI 3750 doesn't support "shape" command under policy map. How do I limit the bandwidth to 3 M? [code]
View 3 Replies View RelatedCan I limit bandwith for guest in a wlan network with out Wlan controller? and of course, how can I do it?P.S.: I heard something about bronze profile in a wlan controller envoiroment, I need something like that but in an independent AP.
View 3 Replies View RelatedAny idea for limiting bandwidth on cisco 892F router? We have 2 VLANs through our LAN and one must be limited upto 1Mbps or 512Kbps.
View 2 Replies View RelatedHow do I setup this on the SRP527W? I already block most of the video stuff on the internet. But I want to make this one more step.
View 1 Replies View RelatedI am looking for some tips on managing my router. I have noticed lately our bandwidth useage has gone up and maxing our DSL line.Cacti is monitoring just for traffic trending and I am in the middle of getting NetFlow going.
Our router sits on the edge with no internal way to access it (or at least so I think right now.)
My thought is to enable NetFlow and port forward it into our network and use ManageEngine to see whats going on.I dont have any ACLs running on the router... We have two connections DSL and T1, I have them into a routing policy.Our nating and firewall sit behind the 2811.
I am trying to use GNS to simulate this, but a bit difficult to achieve this. May I know can the Cisco Router handle below requirement? Example Cisco 2811
1) Bandwidth management based on IP Address or Subnet? For example; allocate 1Mbps (CIR) and 10Mbps (BIR) to 172.16.1.10
2) Can the Cisco Router control the inbound and outbound bandwidth?
3) Can you share the sample config?
Router 2811 got 3 Interfaces. One Interface connected to INTERNETProvider, Second Interface connected to Sales_Dept, Third Interface connected to Business_Dept. Internet Bandwidth in Total is 8MB. I need assistance to allocate 6MB total bandwidth to Sales_Dept and 2MB total to Business_Dept Sales_dept has 48port switch 2960, Business_Dept 24 port switch 2960. Gateway for users is the 2811 Router and both are on different subnets
View 3 Replies View RelatedI got connected ASA ----- ROUTER 2811) to metroethernet switch from my ISP , with a 4MB of bandwidth but the internet connections to all my LAN has been frozen and we lost connection to the internet, to restart the internet service I need to boot the ROUTER 2811 - and ISP switch to rollback the internet operation,My ISP support tell me if is possible to set up the traffic bandwidth in one or both borders devices, ( ASA 5510 or ROUTER 2811)
View 3 Replies View RelatedI'm seeing on an IOS VPN Tunnel interface which keeps going down and then back up...
We have a Cisco 2811 acting as a VPN Hub router on the backbone, which connects to various client sites over VPN. Of the 7 VPNs configured so 6 work well and are generally trouble free. The VPN interface on the other VPN keeps going down ,multiple times throughout the day, just recently the client has been noticing loss of connectivity. The remote router is managed over the VPN so there is always some kind of traffic over it.
*Sep 7 06:40:53.631: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel111, changed state to down
*Sep 7 06:41:23.991: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel111, changed state to up
[Code]......
ISP on each circuit cannot provide more than 3MB, so soon will get three circuit each of 3MB. ISP recommends to terminate all the links on Layer2 switch and have a trunk to the Router. I need all experts opinion on this proposed setup. We currently got 2811 with two GigaEthernet ports. We plan to have three GRE over IPSEC Tunnels (One tunnel for each circuit) to load balance/load Share/redundancy.
View 7 Replies View RelatedI have a cisco Swtich SGH 300-20 Gigabit switch i configure 2 vlan one is default and one is vlan 10
Vlan 1 ip range 172.16.0.0/23
Vlan 10 ip range 172.16.2.0/24
Client on Vlan getting Proper IP from DHCP Server all i need is to distribute internet bandwidth we have 6/3 mb and i want to give 4/2 mb to vlan 1 and 2/1 mb to Vlan 10
Int Gi16 on switch is configured as trunk port and is connected to cisco 2811 router
what are the command used to distribute bandwidth between these 2 vlans
We have point to point metro ether net link terminating on 7204VXR router.On this point to point link we are configuring GRE over ip sec. Problem is when the traffic exceeding 8mbps we started getting packet drops. from the Cisco documentation it seems the tunnel bandwidth is by default 8mbps and there is parameter like Inherit/receive but those actually not change the tunnel interface bandwidth.If we just give tunnel bandwidth with bandwidth mentioned it allows me to give option of 100mbps but again the tunnel interface bandwidth remains 8mbpos only and probably that 100mbps is useful only for routing decisions.
i am using advance security 12.4.15T12 image. Whether this is a limitation or any other way to go beyond 8mbps for the tunnel interface (7204VXR-NPEG1 processor)
I have a task of setting up bandwidth limit on the 2811 router Fastethernet interfaces.The scenario is:We have a 4MB Internet connection and would like to allocate bandwidth usage to users.
Fastethernet 0/0 needs to be set with 256KB output and 2048 input. This is going to be connected to a wireless router. Fastethernet 0/1 needs to be configured with 2048 output.I could also use SDM if that's easier than using CLI.
A multipoint GRE (mGRE) and IPSec tunnel is built between two routers. The topology of the device is briefied below:Configuration in End Router: This is a cisco 2811 router. Amoung 2 ethernet interface ,one is using for LAN and one is for WAN. In WAN part , we have configured mGRE (Tunnel1 and Tunnel 2)by creating sub-interface of the router. From the interface ,we terminating the link to MPLS cloud from there its pointing towards our core router.From End router we are advertising the path through EIGRP and from the cloud BGP advertisied to the core router.[code]
View 1 Replies View RelatedI have a Cisco 1941 router with the Security license running IOS c1900-universalk9-mz.SPA.151-4.M.bin. Is there a "tunnel bandwidth" command like with routers that have the Advanced IP Services license? My concern is being able to adjust the bandwidth to a value greater than 8 Mbps...
View 3 Replies View RelatedWe have a major poblem going on with our VPN router.We have a 7206vxr router which has an mGRE tunnel forming EIGRP neighbourship with about 800 remote locations using GRE over IPsec.
We have a problem where the EIGRP neighbourship keeps flapping intermittently and this happens to 30-40 locations at one time and very frequently.What I noticed was that the GRE tunnel transmit bandwidth was showing as 8 Mbps. I guess there is an option to change it.Will this 8 Mbps limit cause any issues of EIGRP neighbourship flaps and will increasing the bandwidth useful.
We are also seeing output drops on the tunnel interface.
pcvpnstore#sh int tu0Tunnel0 is up, line protocol is up Hardware is Tunnel Internet address is 10.254.254.254/16 MTU 17912 bytes, BW 30000 Kbit/sec, DLY 50000 usec, reliability 255/255, txload 244/255, rxload 110/255 Encapsulation TUNNEL, loopback not set Keepalive not set Tunnel source x.x.x.x (GigabitEthernet0/2) Tunnel protocol/transport multi-GRE/IP Key 0x328CDF, sequencing disabled Checksumming of packets disabled Tunnel TTL 255 Tunnel transport MTU 1472 bytes Tunnel transmit bandwidth 8000 (kbps) Tunnel receive bandwidth 8000 (kbps) Tunnel protection via IPSec (profile "dmvpn") Last input 00:00:00, output never, output hang never Last clearing of "show interface" counters 00:17:06 Input queue: 0/800/0/0 (size/max/drops/flushes); Total output drops: 732
We are facing network heavy and slow performance at one of our remote site, we are using Cisco2800 series router with same IOS on either of the sites.Our WAN network is running on BGP with EIGRP configured and tunnels were configured on either of the sites. As part of the testing I have removed the tunnel to see the performance was ok from Head office to remote branch and the WAN network is getting heavy and slow down when we put the tunnel back in hub and spoke.
quick info
Cisco 2800 Series router
IOS: (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)T1, RELEASE SOFTWARE