Cisco Switches :: 2811 Router / SGH 300-20 For Distributing Bandwidth Between Vlans
May 1, 2012
I have a cisco Swtich SGH 300-20 Gigabit switch i configure 2 vlan one is default and one is vlan 10
Vlan 1 ip range 172.16.0.0/23
Vlan 10 ip range 172.16.2.0/24
Client on Vlan getting Proper IP from DHCP Server all i need is to distribute internet bandwidth we have 6/3 mb and i want to give 4/2 mb to vlan 1 and 2/1 mb to Vlan 10
Int Gi16 on switch is configured as trunk port and is connected to cisco 2811 router
what are the command used to distribute bandwidth between these 2 vlans
View 3 Replies
ADVERTISEMENT
Mar 21, 2013
We have two 2811 router with configured interfaces:
Router1
interface FastEthernet0/0.380 encapsulation dot1Q 380 ip address 192.168.232.18 255.255.255.248 no snmp trap link-status crypto map clientmap!
interface FastEthernet0/0.382 encapsulation dot1Q 382 ip address 10.132.1.126 255.255.255.252 no snmp trap link-status
interface Vlan1 ip address 192.168.5.1 255.255.255.128 ip nat inside ip virtual-reassembly
ip route 0.0.0.0 0.0.0.0 192.168.232.17
ip route 10.132.254.35 255.255.255.255 10.132.1.125
Router2
interface FastEthernet0/0.197 encapsulation dot1Q 197 ip address 192.168.222.2 255.255.255.248 ip nat inside ip virtual-reassembly no cdp enable
interface Vlan1 ip address 192.168.1.1 255.255.255.128 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452
So my case is: computer from router1's network can ping 192.168.222.2 (router2 -FastEthernet0/0.197 )computer from router2 network can ping 192.168.232.18 (router1- FastEthernet0/0.380),but can't ping 10.132.1.126 (router1- FastEthernet0/0.382).
How can i connect vlan 380 and vlan382.I want the three vlan to see each other.Is this happen with IRB or not?
View 4 Replies
View Related
Jun 2, 2011
my problem is this:we have two 2811 router with configured interfaces:
Router1
interface FastEthernet0/0.380 encapsulation dot1Q 380 ip address 192.168.232.18 255.255.255.248 no snmp trap link-status crypto map clientmap!
interface FastEthernet0/0.382 encapsulation dot1Q 382 ip address 10.132.1.126 255.255.255.252 no snmp trap link-status
interface Vlan1 ip address 192.168.5.1 255.255.255.128 ip nat inside ip virtual-reassembly
ip route 0.0.0.0 0.0.0.0 192.168.232.17
ip route 10.132.254.35 255.255.255.255 10.132.1.125
Router2
interface FastEthernet0/0.197 encapsulation dot1Q 197 ip address 192.168.222.2 255.255.255.248 ip nat inside ip virtual-reassembly no cdp enable
interface Vlan1 ip address 192.168.1.1 255.255.255.128 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452
so my case is:computer from router1's network can ping 192.168.222.2 (router2 -FastEthernet0/0.197 )computer from router2 network can ping 192.168.232.18 (router1- FastEthernet0/0.380),but can't ping 10.132.1.126 (router1- FastEthernet0/0.382)How can i connect vlan 380 and vlan382.I want the three vlan to see each other.Is this happen with IRB or not?
View 11 Replies
View Related
Aug 29, 2012
I am trying to use GNS to simulate this, but a bit difficult to achieve this. May I know can the Cisco Router handle below requirement? Example Cisco 2811
1) Bandwidth management based on IP Address or Subnet? For example; allocate 1Mbps (CIR) and 10Mbps (BIR) to 172.16.1.10
2) Can the Cisco Router control the inbound and outbound bandwidth?
3) Can you share the sample config?
View 7 Replies
View Related
Jan 6, 2011
I got connected ASA ----- ROUTER 2811) to metroethernet switch from my ISP , with a 4MB of bandwidth but the internet connections to all my LAN has been frozen and we lost connection to the internet, to restart the internet service I need to boot the ROUTER 2811 - and ISP switch to rollback the internet operation,My ISP support tell me if is possible to set up the traffic bandwidth in one or both borders devices, ( ASA 5510 or ROUTER 2811)
View 3 Replies
View Related
Jun 1, 2012
I am trying to configure router on a stick with 2811 and 3750, but I just cannot get it to work - vlans are not getting propagated from 3750 to 2811: 3750:
Code...
View 1 Replies
View Related
Mar 23, 2013
I have a task of setting up bandwidth limit on the 2811 router Fastethernet interfaces.The scenario is:We have a 4MB Internet connection and would like to allocate bandwidth usage to users.
Fastethernet 0/0 needs to be set with 256KB output and 2048 input. This is going to be connected to a wireless router. Fastethernet 0/1 needs to be configured with 2048 output.I could also use SDM if that's easier than using CLI.
View 2 Replies
View Related
May 31, 2012
I have 2 ISPs terminating on 2 FE ports on my 2811 router.ISP1 had always been here, used for the following:Internet access to LAN usersInternet access with public IP mapping to servers in different security zones (VLANS)Site to Site VPN tunnels to 3rd party partnersRemote VPN access to 3rd party partners We recently got a second ISP, mainly for the following:Internet access and public IP mapping to servers on seperate security zones (VLANS)Site to Site VPN tunnels to 3rd party partners as above, but different hosts So far, ISP1 and all the above service have worked based on the config below. However, having added ISP2, I have not been able to successfully create the site-to-site VPN tunnels.
version 12.4
!
ip source-route
!
ip cef
!
ip name-server 4.2.2.2
ip name-server 137.65.1.1
ip inspect WAAS enable
[code]....
Whenver I try to establish a tunnel on SDM_CMAP_2 and run a test using CCP, I get 2 failure reasons:
1. The peer must be routed through the crypto map interface. The following peer(s) are routed through non-crypto map interface - 4.58.130.130
2. The tunnel traffic destination must be routed through the crypto map interface. The following destinations are routed through non-crypto map interface - 4.58.130.134
The tunnels on SDM_CMAP_1 are all active Do I need to include a default route for the second ISP on the router? If so, how do I get this done? When I tried it, I had loops on the user LAN segment of the network.
View 5 Replies
View Related
Nov 30, 2011
What are the benefits of using a Layer 3 switch as opposed to a router for distributing traffic? Basically the building I work in has a fiber line coming in which then gets connected to a Level 3 switch (NetVanta 1534) which is then connected to all the ethernet ports and what not. Why would they choose to use this device as opposed to a router? Or just a regular Layer 2 switch?
View 12 Replies
View Related
Aug 29, 2012
I am looking for some tips on managing my router. I have noticed lately our bandwidth useage has gone up and maxing our DSL line.Cacti is monitoring just for traffic trending and I am in the middle of getting NetFlow going.
Our router sits on the edge with no internal way to access it (or at least so I think right now.)
My thought is to enable NetFlow and port forward it into our network and use ManageEngine to see whats going on.I dont have any ACLs running on the router... We have two connections DSL and T1, I have them into a routing policy.Our nating and firewall sit behind the 2811.
View 1 Replies
View Related
Jun 10, 2013
We have two Cisco 2811 Routers setup with a GRE tunnel that we would like to constrain the bandwidth on to replicate a satellite connectinon of 400 kbits. We tried the bandwidth command 400, but from what I understand that is only for routing metrics and not actual speed of the interface.
View 5 Replies
View Related
May 1, 2012
Router 2811 got 3 Interfaces. One Interface connected to INTERNETProvider, Second Interface connected to Sales_Dept, Third Interface connected to Business_Dept. Internet Bandwidth in Total is 8MB. I need assistance to allocate 6MB total bandwidth to Sales_Dept and 2MB total to Business_Dept Sales_dept has 48port switch 2960, Business_Dept 24 port switch 2960. Gateway for users is the 2811 Router and both are on different subnets
View 3 Replies
View Related
Jul 10, 2012
i am trying to get a SG300 work as a router between VLAN's?So fare without any lock?Test setup one SG300 switch and 2 PC's ?Ping works from host to VLAN IP's, but not from host A to host B
Here is the host configuration
<TABLE style="BORDER-BOTTOM: #000000 1px solid; BORDER-LEFT: #000000 1px solid; WIDTH: 400px; BORDER-TOP: #000000 1px solid; BORDER-RIGHT: #000000 1px solid" class=jiveBorder border=1 cellSpacing=0 cellPadding=3 mcestyle="BORDER-BOTTOM: #000000 1px solid; BORDER-LEFT: #000000 1px solid; WIDTH: 400px; BORDER-TOP: #000000 1px solid; BORDER-RIGHT: #000000 1px solid">
[code]...
Here is the switch configuration
SG300 with FW 1.1.2.0 configuration i L3 mode
set system mode router
confip routing (needed on SG300??? - ti is on a 3560 i PacketTracer)
vlan databasevlan 5vlan 6vlan 7
[code]...
View 5 Replies
View Related
Jan 23, 2012
Currently, we have a Cisco router (28xx), ASA 5520, and a core switch 4500. We have different vlans. We also have Auto QoS running for our Cisco IP Phones.My manager just asked me to see if I can either reserve some certain bandwidth for one vlan, or give that vlan higher priority on internet traffic than the others.
1.) Anyway we can reserve some more bandwidth for one vlan than other vlans?
2.) If #1 cannot be done, how can we provide higher priority on the internet traffic to one vlan than the others?
3.) Is #1 or #2 the same config? If not, which one would be easier (without changing our current QoS settings)?
4.) If 1 or 2 can be done, which device I should config the settings on?
5.) This question may be duplicate, but do we need to reset our current QoS to achieve the goal?
View 6 Replies
View Related
Oct 9, 2012
This is existing network diagram and find attached file for configuration of Router and L3 Switch:ISP provided 6 Mbps internet access link with ethernet Handoff which is terminated over Cisco 1841.ISP also provided pool of 30 Public ip's 125.63.74.33 /27 , range from 125.63.74.34 to 125.63.74.62.In my current setup, all Inside to ouside traffic going out through 125.63.74.34 public ip because this public-ip NAT overload with Router F0/1 interface.
1) I want to divide 6 Mbps link physically into three parts 2Mbps, 2Mbps, 2Mbps for three VLANs.
2) I want to also configure each vlan IN/OUT traffic with different Public ip. is it possible or not ?
Vlan2 = 172.25.162.0 /24 => Inside to outside / Outside to inside traffic through 125.63.74.40
Vlan3 = 172.25.163.0 /24 => Inside to outside / Outside to inside traffic through 125.63.74.41
Vlan4 = 172.25 164.0 /24 => Inside to outside / Outside to inside traffic through 125.63.74.42
How can i configure above desired setup with CBWFQ
View 23 Replies
View Related
Aug 20, 2012
I have 2 switch groups.
2 SGE2010's with VLAN's defined as 10,20 and 30
Vlan 10 is the management VLAN, and it uplinks to our border router.Vlan 20 is the workstation VLAN, and all workstations point to the switch as their default GW? Vlan 30 is the ip phone VLAN, and all phones use this as their gateway.
I would like to put a LAG between said switches, we have some servers on the ip phone switch that need to be accessed by the workstation clients, and the single 100mb link through the router is probably not going to be enough.As I understand it, because the switches have different networks on them, a simple lag will not work. I did create a lag, and assign ip addresses to each side, however in that mode, it doesn't appear I can block vlan 10 from transiting the LAG, and with out that block I will end up with a logical loop, and spanning-tree will block one of the uplinks, or the LAG itself.
View 10 Replies
View Related
Jul 17, 2012
I was looking for configuring QOS for two VLANS i have created. these will be for voice traffic vlan 22 and video traffic vlan23. i also have three other vlans for pc's, wireless devices and our cnc machines. we have 5 switches that are all SG30028P's with a single switch doing the intervlan routing (operating at layer 3). all of the switches are trunked back to the main switch and ive been through the guide written on how to do this on a single switch which i dont think is layer 3.
View 5 Replies
View Related
Aug 20, 2012
I'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
View 3 Replies
View Related
Apr 8, 2011
I am using using 2 broadband with tp-link dual wan router 10 pc using the broadband.does any one know about the router who controls bandwith there is option available in Tp-Link Dual wan router but its not working...is there any router which automatically takes bandwith and allow as per my details.
View 1 Replies
View Related
Jan 21, 2013
I work for a company that recently upgraded to a Cisco RVS4000 router in place of a failing D-Link router. I configured the RVS4000 to utilize the same address space as the D-Link previously did (192.168.0.0 Network Address, 255.255.255.0 Subnet Mask, RVS4000 in Gateway Mode with IP Address 192.168.0.1, DHCP Scope from 192.168.0.101 - 200 managed by the RVS4000) before installing it on the network. I powered down the D-Link as well as the cable modem, then all of the workstations in the office. Then, I installed the RVS4000, powered up the cable modem, and once it was ready, powered on the RVS4000.
When devices connect, the RVS4000 is assigning them an IP address in the 192.168.1.0/24 subnet, instead of the 192.168.0.0/24 subnet. I have verified that the RVS4000's GUI is showing the correct settings, but connected devices are not picking up addresses from the correct address pool. In troubleshooting, I went to each workstation, released and renewed their IP addresses, and they picked up addresses in the correct subnet. I thought everything was solved, but the next day, the same problem resurfaced.
I left the DHCP lease time at the defaul value "0", which according to the unit's documentation should correspond to a 24-hour lease period. I suspect this is why I had to renew the clients' IP addresses the next day (today), but I still don't get why the RVS4000 wants to give out addresses in the 192.168.1.0/24 scope. Could this be a holdover from the factory settings?
Additional Information: I did not set up any VLANs on the network and the office only requires one subnet as there are not a lot of devices connected, nor do we need the traffic segragated. The VPN functions of the RVS4000 work fine. Using the QuickVPN utility, I can access the network and resources on the network remotely without issue.
View 2 Replies
View Related
Aug 13, 2011
I just received a new Cisco SG300-10 and am configuring it in Layer 3 mode. I am trying to setup multiple routed VLANs going back to a FiOS Actiontec router. My configuration is as follows.
Fios Router: 192.168.1.1
Assigning DHCP 192.168.1.2 through 100.
SG300-10 has VLan 1 ip 192.168.1.5 used for Mgmt.
VLAN2 is 10.0.2.1
VLAN3 is 10.0.3.1.
I have a static route set on the fios router for both subnets setup as follows.
Destination 10.0.3.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
Destination 10.0.2.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
I have a laptop connected to Gi8 on the Cisco (Vlan 3) and statically assigned 10.0.3.3, with a gateway of 10.0.3.1. DNS set to the fios router (192.168.1.1).
Everything pretty much works EXCEPT, I cannot get out to the internet from either vlan. Traffic routes between vlans/and the default subnet on the fios without issue.
When I ping out, DNS resolves, but will not go past the fios router. Am I missing a setting somewhere?
View 3 Replies
View Related
May 22, 2011
I am trying to set up three vlans across two switches. The switches are Cisco SG200 and SG 300 series. There are 20 devices connected to the two switches including a router for Internet. Among these devices are five wireless access points all hardwired to the LAN. If I understand correctly the first thing I have to do is aggregate the two switches. I ran two cat5 cables to ports 1 and 2 of each switch. As I understand it all I need to do is to create SAG with the two ports on each switch. I think I need to use tagging but I don't really understand how to do this. Once I get the trunking set up correctly I want to create one vlan to which all devices will belong for Internet access. The other two would be for data and VoIP. Do I create vlans with the same name on both switches? When I assign the devices (by port) do I need to enable tagging? Which type of port setting should I use? I am assuming that by including the acess points in the vlans will mean that any wireless device connected to them will have acess to the Internet and the devices in the same vlan.
View 1 Replies
View Related
Apr 12, 2012
I have a 4 port etherchannel configured to talk to a 4 port etherchannel on NETAPP server. The NETAPP server seems to be distributing traffic across all the links. The 4507 does not. It appears that traffic is going across only 2 of the for links. [code]
View 6 Replies
View Related
Sep 9, 2012
I am trying to get WOL working across different VLANS on a SG-300-10 Switch in Layer 3 Mode. To achieve this, I've setup an UDP-Relay (GUI menu IP Configuration) for UDP-Port 7 to 255.255.255.255 (this should flood all interfaces with the paket), however, WOL doesn't work across different VLANS. When I am connected directly to the corresponding VLAN, WOL works fine within the same subnet.
View 2 Replies
View Related
Mar 22, 2012
How shall i use different vlans outside another gateway in sg-300 28? Example:
vlan2 192.168.2.0/24 gateway 192.168.2.1 outside router gateway 192.168.2.254
vlan3 192.168.3.0/24 gateway 192.168.3.1 outside router gateway 192.168.3.254
should me doing in sg-300 28?
View 1 Replies
View Related
Jan 30, 2012
Trunk from 3500 going into SF300-8 #1 QNQTrunk from SF300-8 #1 going into trunk SF300-8 #2QNQ from SF300-08#2 going into Trunk SF300-24, All Vlans from Network 1 seem to be communicating properly between the 3550 and SF300-24 and is isolated from the Transport Network by QnQ. I am having one problem, I can not ping the SF300-24 or get to the management interface. I am able to access other devices on the SF300-24 Vlan1 from devices on the 3550 Vlan1 and vice versa.
View 1 Replies
View Related
Apr 12, 2013
At the moment i have 2 internetconnentions with 2 different modems/routers. The computers are currently direct connected to the router.I'm considering adding a switch in the network and i hope i can make 2 different vlans each for one internet connection. The two networks should not be able to connect eachother.But i dont know what switch i need to do that. Do i need a Sg-200 or a SG-300 switch?
View 1 Replies
View Related
Aug 26, 2012
I have 2 SG300-10 switches, and I need two VLANs, one for internal network and one for WiFi APs.I need ports 1->4 on both switches to be part of 1st VLAN and ports 5->8 on 2nd VLAN; and port 10 uplink to 2nd switch.How I set up the VLANs and interface VLAN mode?
[code]...
View 1 Replies
View Related
May 22, 2011
My ISP is providing me with 1 public IP on a /30 network and 14 public IPs on a /28 network. In this example the 10.0.0.1 is the default gw provided by my ISP and 10.0.0.2 is my SF300-08. If I setup my router to route to 10.0.0.2 as the default gw through the interface between the switch and router, can I configure the static routes in the switch to route further to 10.0.0.1?
is it possible to have these 2 networks on different VLANs and configure inter-VLAN routing? I don't want the switch accessible from the 10.0.0.2 IP.
View 3 Replies
View Related
Apr 9, 2013
I am IT teacher at a middle school in Nuremberg, Germany. We have in our school 5 VLANs, 4 Switchtes, 1 L3 switch and 1 router.
2 months ago the old L3 switch (Catalyst 3550-12T) is broken. In the short term I've borrowed a Catalyst 3750G-24, so that the network continues to function. Now a SG 300-10 switch was purchased. This should be configured the same as the 3550-12T or 3750-24G.The network looks like this (there are much more PCS than in this image):
VLAN ID
VLAN Interface
DHCP
DHCP-pool
[Code]....
The DHCP server in VLAN 30 is also a FOG server. The Fog server images all PCs in school. PCs in VLAN 10, 20 and 30 boot from PXE. The MS Server in VLAN 10 has been configured by the DHCP options 66 and 67.
The Catalyst 3750G-24 routes the multicast, but the SG 300-10 I do not have the option of using the commands ip multicast-routing distributedip pim sparse-dense-modeto work and must configure igmp. I'm having problems with the igmp-configuration on the SG 300-10. Therefore, I have uploaded the configuration of the 3750G-24 and the configuration of the SG 300-10 (without ACL).
View 2 Replies
View Related
Jun 22, 2011
I am having problems accomplishing these tasks with my new SG 200-18.
I have a LinkSys WRT54G2 connected to port 1. I would like ports 2-8 to be in one VLAN with access to the Internet and to be able to share their printers, hard drives, etc. with other computers on ports 2-8. I would like each of ports 9-16 to be on a separate VLAN with access only to the Internet and no other ports on the switch. I would like to be able to manage the switch from any of the ports 2-8.
After I create the VLAN 1009 (see screenshot below), port 9 can browse the Internet and cannot see the other ports on the switch which is correct. However, ports 2-8 can no longer access the switch at 192.168.1.20 in order to manage the switch.
View 10 Replies
View Related
Oct 26, 2011
I am a novice at setting up Cisco routers, I have a few years of networking form the server side of things just beginning to work on the switch side. I am trying to configure a sg200-8 to have three VLANs.
Here are the steps i used:
Create VLAN:
VLAN
VLAN ID: 10
VLAN Name: 22 lab network
Apply
VLAN
VLAN ID: 20
VLAN Name: 23 lab network
Apply
[code].....
View 7 Replies
View Related
May 18, 2012
I have a 2960 and a 2811 with a hwic card I have one port set as 100 meg and another port set at 10 meg. Both are set to access mode. i need one port for failover (10 meg) . I can't do ether channel on the hwic. How do I prevent a loop when I connect my second connection. While having both connections up. Should I use bpdu guard? the goal is to have one port fail over if the 100 meg goes down. And I'm currently running ospf so it should take the faster connection.
View 1 Replies
View Related
