I am using using 2 broadband with tp-link dual wan router 10 pc using the broadband.does any one know about the router who controls bandwith there is option available in Tp-Link Dual wan router but its not working...is there any router which automatically takes bandwith and allow as per my details.
View 1 Replieshow to limit the bandwidth in digicom router?
View 2 Replies View Relatedwould like to know how a bandwidth gets distributed in switches.for example consider a scenariowhere i have a coreswitch A and coreswitch B connected between each other througha a 1Giga Fiber, now each of my core switche are connected to two edge switches through fiber links. all edge switches have giga ports. now if i connect a pc with giga link in th edge switch of coreswitch A and tansfer a file to a PC connnected to the edge switch in network B.. how much bandwidth would i get?how does the switch allocate bandwidth?
View 8 Replies View RelatedI have a 24Mbps (my bandwidth) connection, what I need is that all the computers in my network have the same bandwith. Let's say I have 12 computers so I want the 24 mbps divided across the 12 pc, but if I shut down 4 of those computers , I want some sort of software that would be capable of detecting that activity so my 8 remaining Pc will have more bandwith. I don't know If I was clear enough?what I need to know is:
-is the bandwith will automatically divised between computers?
- at least is this scenario possible?
just as information if I want to create a client/server with one server and 12 clients, and the initial bandwidth= 24Mbps, theoretically, how to devise the bandwidth between all clients, and if one client is shutdown, the bandwidth attached to it, will it redistributed between the other clients? if no, what happen with it?
I have a cisco Swtich SGH 300-20 Gigabit switch i configure 2 vlan one is default and one is vlan 10
Vlan 1 ip range 172.16.0.0/23
Vlan 10 ip range 172.16.2.0/24
Client on Vlan getting Proper IP from DHCP Server all i need is to distribute internet bandwidth we have 6/3 mb and i want to give 4/2 mb to vlan 1 and 2/1 mb to Vlan 10
Int Gi16 on switch is configured as trunk port and is connected to cisco 2811 router
what are the command used to distribute bandwidth between these 2 vlans
I have a scenario where 15 c500 switches and 5 2960 8 port switch connected to 4507R core switch. There are 10 dhcp pools created on the 4507.
Eg: ip dhcp pool XXXX
network xxxx.xxxxxxx
default-router x.x.x.x
Now the default router is directed to vlans created on the switch i.e vlan 101, 102, 103 and so on. Now the remaining switches connected are configured to be in the same vlan. So the systems connected to the edge switches will get the DHCP ip automatically, Now my problem is after sometime (may be 2 or 3 hrs) all the edge switches are losing configuration automatically even though it's not restarted, even after saving the config on to nvram, everytime I connect the console and check all the saved config is lost?
I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
View 3 Replies View Relatedhow to connect two subnets with two switches and one router using router sim software?
View 1 Replies View RelatedI have two RV082's connected across the internets using the primary WAN ports. They are both set to Auto Load Balance. Both ends of the VPN are set to "IP Only, IP by DNS Resolved".
If I attempt to access the remote subnet, the VPN won't automatically initiate a connection. However, if I do a "Tunnel Test" connection on both routers, then the remote subnet access works just fine.
Should the router automatically connect the VPN when a remote subnet is attempted? If so, what might I do to make it connect automatically?
Cisco Rv042 (obtain an ip automatically) problam ?,Firmware Version : v4.1.0.02-tm (Sep 16 2011 18:40:48)
DHCP Server Working, but Cisco Rv042 can't obtain an ip address autimatically on WAN Ports.
How do I get one of these to automatically bring up the VPN tunnel without the end user having to login and click connect? I got the VPN working Dynamic to ASA static, but it doesnt come up on its own when I try to access something over VPN.
View 7 Replies View RelatedI am setting up a dual WAN network in our small business office and I am confussed on the set up of the RV042.
On WAN1 I have a satellite modem connected
On WAN2 I have a cradlepoint CTR35 Router with a verizon aircard
The satellite has lag issues and will drop out during poor weather but has a 17GB dowload limit. The verizon aircard has only 5GB download limit but normally works in poor weather. Code...
Do I select obtain DNS automatically on both WAN1 and 2? Do I set this up as a gateway or a router?
I purchased 2 RV042's (h/w version 3) less than two months ago. I updated them to the latest firmware (v4.0.4.02-tm (Jul 4 2011 13:30:56)), did a factory reset to make sure I was working with a clean slate, set up DDNS through DynDNS and a site to site VPN between the two. Everything was working great for a month, then the DynDNS accounts expired because they weren't being updated. I reactivated the names on the DynDNS site, and started to monitor the "last updated" date and time. After 24 hours there were no updates according to the DynDNS site. I logged into one of the RV042's, and it said "Dyndns Enabled : Dynamic DNS is updated successfully." This is a stale message from 24 hours ago when I hit save. So I went into Setup | Dynamic DNS | Edit Config and there it also says "Dynamic DNS is updated successfully." I clicked "Save", status changed to " Dyndns Enabled : Updating..." for a few seconds, and then back to "Dyndns Enabled : Dynamic DNS is updated successfully". I refreshed the DynDNS website and it shows the current time (in eastern time, i'm pacfic) as the last time it was updated. So it works when I manually hit the "Save" button. Not making any changed, just hitting "Save". I've let the other RV042 go over 48 hours and it still hasn't updated. So it apears for the time being, I'll have to remember to push the "Save" button once a week to prevent my DynDNS accout from expiring. Does DDNS working in the lastest firmware and h/w version 3? If so, what is the update frequency?
View 6 Replies View Relatedi need to access my routers settings. i have my default gateway 192.168.21.254 . i enter that into my web browser, and it takes me to a user agreement page. the whole purpose of this is to set my NAT type to open on my xbox 360.
View 3 Replies View RelatedI have a new d-link wireless N 150 home router DIR-600. I heard of the wan ping which works it connect for online gaming, does or does it not turn on when you install it and is there any other things i can do to improve it? can't connect to League of legends
View 4 Replies View RelatedI have a cisco RV180W with a IPsec tunnel to the head office. The tunnel is working good, but if I reboot the RV180W, the tunnel don’t reconnect automatically, I need to go in the admin interface to IPsec Connections Status and press on Connect.Is there a way to make the tunnel connect automatically?
View 4 Replies View RelatedI have got a very basic/fundamental doubt.I would like to know how a bandwidth gets distributed in switches.for example consider a scenario where i have a coreswitch A and coreswitch B connected between each other througha a 1Giga Fiber now each of my core switche are connected to two edge switches through fiber links. all edge switches have giga ports. now if i connect a pc with giga link in th edge switch of coreswitch A and tansfer a file to a PC connnected to the edge switch in network B.how does the switch allocate/distribute bandwidth?
View 2 Replies View RelatedWhen I start-up my computer, it takes over an hour to find my router on my computer (Not on my brother's computer, or the computer upstairs). Once it does, it connect perfectly. This is very annoying because I do not have a lot of time anyway to work/play and when I do, it takes over an hour to find the router.Recently, I have been having HUGE lag spikes, constantly disconnecting from games and skype calls.
View 1 Replies View RelatedRegion : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP :
Region : Others
Model : TL-MR3220
Hardware Version : V1
Firmware Version : latest
ISP : Orange
The TL-MR3220 takes a long time to identify the 3g modem and sometimes it will not identify it at all and says "unplugged". Sometimes "unplugged" suddenly apears after the modem has been identified and was working properly.Is this the normal behavior of this device ? Why ? What can be done ? I'm Using Alcatel X500D 3g modem.
I have a WRK54G v2 connected to a Ubee cable modem, and when my computer, connected with wifi or ethernet, tries to play a Youtube video, the actual webpage loads fine but the spinning dots in the player remain for several minutes before the video starts to load. If the video has to buffer again in the middle of playback, it also takes several minutes to start again. When the computer is connected directly to the cable modem, everything works fine. Youtube is the only site I am having an issue with, other video streaming sites like Vimeo work fine.
View 9 Replies View RelatedWhen I boot my system lately I have to fiddle with task manager to get things stable enough to connect to my network. This is getting very tiresome. I always find OdHost.exe taking almost all the CPU and have to kill it to get things running. This can't be normal and has not been until recently. I don't know of anything that has been installed in the last several months that is network related.
View 1 Replies View RelatedNot sure if I have a defective router, but if I unplug it I then need to wait at least a half hour to plug it back in. Anytime sooner and it won't broadcast a SSID or connect to the modem. This is a huge inconvenience if you want to change router settings and then you need to restart.
View 1 Replies View RelatedI have a SG 300-20 small business switch and I would like to restrict bandwidth by gateway ip address but not by physical port or LAG. On the web interface, I can only do bw limiting per port or lag. I want to do bandwidth limiting by the IP addresses that I assign to vlans that my hosts use as a gateway ip.
View 3 Replies View RelatedJust put in an SF302-08P switch with two AP541N's. Just a Comcast modem connects into the switch along with the two WAPs, nothing else. Speedtest through the cable modem with nothing plugged into it is 48Mbps. Then connecting a single laptop via the switch shows a speedtest of 33Mbps. Then with the two AP541N's plugged in and using the same laptop over WiFi, I'd consistently seen 10Mbps for downloading. But going right back to the cable modem directly showed me close to 50Mbps in a speed test.
Have factory defaults in all the Cisco devices, and poured over the settings and it looks like bandwidth limiting is disabled. Suspecting maybe it is for QoS and to optimize voice, but I see definite places in the devices where I could designate optimizing voice and those aren't enabled. Then started thinking with tweaking the wireless frequencies, but didn't want to do anything too unstable.
Does the SGE2000 supports NetFlow? I've checked the Cisco docs and also called Cisco support to which no one has been able to answer me.
Anyhow, just in case it doesn't support NetFlow, how to be able to set up something that would be able to check the bandwidth usage on each port?
I've got a problem where I think the SGE2000 switch is failing when I pump around 190~200Mbps through x2 of the ports (Server A on port 1=130Mbps and Server B on port 2=60Mbps) of Multicast traffic (UDP). I can measure the output from the Streaming servers that provide the multicast content, thats how I know the input to the switch and I know that there are no packets lost or any errors departing from the servers, yet when I increase server B to say 80Mbps, I get break up and all sorts of problems on the client end STBs and it is happening on the multicast content provided by Server A too which is a different source, so I'm 99.9% sure its a SGE2000 switch problem which is why I'd like to monitor it somehow.
I'd like to use an SG200 swicth to allocate bandwidth on a 100 Mbps fiber Internet uplink.I will have 5 routers (each supporting a separate network) connected to the SG200, and I'd like to give each network 20 Mbps. QOS configuration, best CIR and CBS settings for this.
View 1 Replies View RelatedMy home network has two routers. My setup is...modem to router 1, then router 1 to router 2. is there a way to track the bandwidth usage on the two routers. My ISP says that I'm going over my bandwidth allowance and that's because in my household, we are hardcore gamers, netflix, and internet users. Router 2 belongs to my sister-in-law, and router 1 is mine. But I want to know which and more importantly, "WHO" is using more of the bandwidth.
View 3 Replies View Relatedi have a router connected to my ISP which can get me 2 different IP's at all times (the router gets one IP).Now i want to get my computer to have a different ip as my router has (seen from outside my home network) - i want my computer that accesses the internet through my router to have a different IP as my router. I know that if my computer gets it's IP from my router's subnet, then it will (seen from outside) always have the same IP as my router. So the question is how do i get around this ? Do i just have to change my PC's DNS / gateway settings to match my router's ? The PC is connected to my router via wifi. Or would forwarding some ports on my router work ?
View 3 Replies View RelatedWhen someone downloads a file, or similar, there seems to be no, or very little, room for other requests. I've even tried to be the only one on the network, start a download (from ex. Intel) and then tries to access a simple website, almost only text, and its extreemly slow. I hav ethe latest firmware, a windows domain network and the routers is not acting as dhcp server.
View 4 Replies View RelatedI just got the RV042G today. I found the router can only accept 100000 Kbit/sec as bandwith, which is 100Mps only. According to the specification, it should have 1000Mps WAN. I have a internet link of 1000Mps, which is now limited by this router.
View 30 Replies View RelatedSince I've bought my RV042 CISCO (v3 hardware, firmware v4.1.1.01-sp Dec 6 2011 20:03:18) i wasn't able to let it work properly with my two DSL network lines. I explain. I got 2 DSL network:
1- PPPoE with authentication (MTU setted as auto) with upstream speed 4Mbit/S and downstream speed 5Mbit/s
2- Direct line with static IP with upstream speed 7Mbit/S and downstream speed 1Mbit/s
I was never able to SUM the two WAN using the LOAD BALANCE set. I tried all combinations:
DSL 1 in WAN 1 or in WAN 2
DSL 2 in WAN 2 or in WAN 1
I've tested all type of speeds in WAN SPEED in Web Management
it seems that for some kind of reason it takes the upstream speed i can set in web management as the default value on which it decides to use the other WAN. When i set low upstream bandwidth for DSL 2 it's able to sum the down streams of both WANs but not the up streams.
I wasn't ever able to sum the up streams? How does it work?
I have an RV220W which I would like to set bandwidth limiting on. When we upload files to yousendit or an FTP server, it saturates the connection and essentially stops any other traffic until the upload is finished. Looking at the manual, it looks like it should do this, but does not seem clear to me.
View 1 Replies View Relatedsetting up Rate Control in Bandwidth Management. It doesn't seem to work at all. I knew from some other Posts that I need to have IPS on and I do.. Is there something else I need to do.
My users are connected wirelessly to the router through three different SSIDs and I have 3 VLANS. I need to set some limitations on two of the LANS.