How do I get one of these to automatically bring up the VPN tunnel without the end user having to login and click connect? I got the VPN working Dynamic to ASA static, but it doesnt come up on its own when I try to access something over VPN.
View 7 RepliesI have a cisco RV180W with a IPsec tunnel to the head office. The tunnel is working good, but if I reboot the RV180W, the tunnel don’t reconnect automatically, I need to go in the admin interface to IPsec Connections Status and press on Connect.Is there a way to make the tunnel connect automatically?
View 4 Replies View RelatedI know I can bring up a tunnel up-and-up without any layer 3 address, without any ipv4 or ipv6 address (apart from tunnel source/destination of course). And I don't have to use "ip unnumbered <interface>" either. But what good is a tunnel interface with no address? Can you bridge them or something?
View 5 Replies View RelatedI am trying to configure an IPSEC tunnel on a 1921 router. What I hope to accomplish is that using a IP SLA that the IPSEC tunnel will only be brought up IF the normal WAN connection is not responding. My thoughts were to route the traffic that needed to come back to corporate through a loopback interface but I havent found a way to do that.
View 1 Replies View RelatedLinksys tried multiple WRT54g routers and access point, 192.168.1.1 can't open the router config page.
View 5 Replies View RelatedI am using a Cisco RV110W (Firmware 1.2.09) in a branch and I would like to create a VPN Tunnel to another site that has a Cisco RV042 (firmware v4.2.1.02)
What would be the correct Configuration? the current configuration I am using is
in the RV042 i am using
Check Enable
Local Group Setup
Local Security Gateway Type : IP Only
IP Address : RV042 Pulbic IP address
[Code].....
Environment :linksys wrt300n v1.1 which can have ddwrt-mega. Willing to tunnel all lan's outbound traffic through an ssh tunnel.
View 2 Replies View RelatedI have two RV082's connected across the internets using the primary WAN ports. They are both set to Auto Load Balance. Both ends of the VPN are set to "IP Only, IP by DNS Resolved".
If I attempt to access the remote subnet, the VPN won't automatically initiate a connection. However, if I do a "Tunnel Test" connection on both routers, then the remote subnet access works just fine.
Should the router automatically connect the VPN when a remote subnet is attempted? If so, what might I do to make it connect automatically?
Cisco Rv042 (obtain an ip automatically) problam ?,Firmware Version : v4.1.0.02-tm (Sep 16 2011 18:40:48)
DHCP Server Working, but Cisco Rv042 can't obtain an ip address autimatically on WAN Ports.
I am setting up a dual WAN network in our small business office and I am confussed on the set up of the RV042.
On WAN1 I have a satellite modem connected
On WAN2 I have a cradlepoint CTR35 Router with a verizon aircard
The satellite has lag issues and will drop out during poor weather but has a 17GB dowload limit. The verizon aircard has only 5GB download limit but normally works in poor weather. Code...
Do I select obtain DNS automatically on both WAN1 and 2? Do I set this up as a gateway or a router?
I purchased 2 RV042's (h/w version 3) less than two months ago. I updated them to the latest firmware (v4.0.4.02-tm (Jul 4 2011 13:30:56)), did a factory reset to make sure I was working with a clean slate, set up DDNS through DynDNS and a site to site VPN between the two. Everything was working great for a month, then the DynDNS accounts expired because they weren't being updated. I reactivated the names on the DynDNS site, and started to monitor the "last updated" date and time. After 24 hours there were no updates according to the DynDNS site. I logged into one of the RV042's, and it said "Dyndns Enabled : Dynamic DNS is updated successfully." This is a stale message from 24 hours ago when I hit save. So I went into Setup | Dynamic DNS | Edit Config and there it also says "Dynamic DNS is updated successfully." I clicked "Save", status changed to " Dyndns Enabled : Updating..." for a few seconds, and then back to "Dyndns Enabled : Dynamic DNS is updated successfully". I refreshed the DynDNS website and it shows the current time (in eastern time, i'm pacfic) as the last time it was updated. So it works when I manually hit the "Save" button. Not making any changed, just hitting "Save". I've let the other RV042 go over 48 hours and it still hasn't updated. So it apears for the time being, I'll have to remember to push the "Save" button once a week to prevent my DynDNS accout from expiring. Does DDNS working in the lastest firmware and h/w version 3? If so, what is the update frequency?
View 6 Replies View RelatedI am using using 2 broadband with tp-link dual wan router 10 pc using the broadband.does any one know about the router who controls bandwith there is option available in Tp-Link Dual wan router but its not working...is there any router which automatically takes bandwith and allow as per my details.
View 1 Replies View RelatedI have a new d-link wireless N 150 home router DIR-600. I heard of the wan ping which works it connect for online gaming, does or does it not turn on when you install it and is there any other things i can do to improve it? can't connect to League of legends
View 4 Replies View RelatedIm trying to setup a site to site VPN using a Cisco 877, problem is we have no ADSL presentation, we've just been given an Ethernet line to use from another client in the building, If i plug my laptop into the port and use the External IP information given i can use the internet and ping the other VPN just fine, if i place my blank config 877 into the port and set up VLAN 10 to use the same IP information, it cant even ping the local gateway? The port on the router is in VLAN 10 like it should be and the interfaces are all up, the router can ping its local VLAN 10 ip address.
View 5 Replies View RelatedHow to set up a home network with 2 routers, where R1 acts as the DHCP server and R2 is basically a switch, connected LAN to LAN and everything is on the same subnet. Currently I have a different setup:Both routers have the DHCP server enabled and I connect R2's WAN port to R1 LAN. Therefore I have 2 subnets. Now my special requirement is that R2 is a DD-WRT router, which establishes a VPN connection to StrongVPN, so that all internet traffic via R2 is encrypted and goes through the StrongVPN server. Now my question:If I change my router setup to the same subnet, meaning R2 connects LAN to R1 LAN and I disable DHCP server on R2, will R2 still be able to establish the VPN connection?
View 5 Replies View RelatedI've attached my ASA's config. I can't bring the VPN up by pinging from the ASA but the VPN will come up when someone pings from behind the ISA server. So the problem seems to be routing/NAT on my ASA because my pings aren't being directed out the tunnel. The VPN in question has 64.106.x.x as the peer and AES 256/SHA for phase 1 and 2.
View 2 Replies View RelatedI have 2 ASR 1006 with ASR-1000-ESP40, ASR-1000-SIP40, ASR-1000-RP2 , and with SPA-1X10GE-L-V2 that should hold an XFP-10G-MM-SR.
i am in the proceed of an implementation and configuration, but i am facing a problem on the interfaces, where i am not able to bring the interfaces up/up and always down/down.
i check the fiber patch cords and the other SFP on the switch WS-C3560E-12D and it is working fine. i also reverse the fibers pins and nothing works
i need only to get the interface to be up/up. i also checked all the hardware compatibility matrix, IOS XE, the SPA are all online (show platforms).... where all seems to be ok and compatible.
all what is needed is to give the interface ,for example, tengig0/0/0 and ip address and no shut and it should go up/up.
One more thing, the XFP is not giving a red light laser, and in the show interface tengig0/0/0 give media type is unknown.
I'm trying to bring up two t1 and bundle them into a multilink on a 3845 on one end and a 3725 on the other end. On the 3845 I have installed two VWIC-2MFT-T1-DI and on the 3725 I have installed two VWIC-2MFT-T1 and a 1DSU/CSU-T1-V2.
For some reason I'm able to bring up the T1's on the DSU/CSU WIC. When I try to connect the T1 on the other WICs, on the 3845 I see SLIPs and Interface Resets however on the 3725 there is no errors however I still see UP DOWN.
CONFIG 3845
controller T1 2/0/0
framing esf
linecode b8zs
cablelength short 133
channel-group 0 timeslots 1-24 speed 64
[code]....
Have already checked in the Device Manager if the �Allow this device to wake the computer� is unchecked.What do I do to bring the sleep mode back without turning off the file sharing (if file sharing caused the problem)?
View 1 Replies View RelatedI've to bring vlan 2 access to a remote site through 2 AP1261N configured as bridges. Here it is the network diagram
One AP1261N is configured as root bridge. Its ethernet interface is connected to a switch with vlan 1 native and vlan 2 tagged. Vlan 1 is for APs and switches management. Vlan 2 is for users access. The other AP1261N is configured as non-root bridge and one PC is directly connected to the AP's ethernet interface. I've successfully managed to create i wireless link between the 2 APs and so I can reach the vlan 1 IP address of the non-root AP. My problem is that I can't reach the PC connected to the non-root AP.
Here are the conf of the 2 APs:
root AP
version 15.2
no service pad
[Code].....
getting step by step procedure to bring an ASA5550 to factory default setting, so that I can configure it from scratch via ASDM
View 3 Replies View RelatedI have 2 4402 WLC running 7.x.x.x code. I also have some 1510 Mesh- L WAPs that require an old version of code. I need 4.1.192.22M for those. Is it possible to bring up a 3rd controller running this old code with the other 2 4402's running modern code? What will break? I know that anchoring and mobility might get messed up. What are the other caveats?
View 2 Replies View RelatedWe have two Comcast 100MB routers. Can I plug these both into the SG200-50? How do I configure the ports?
I have an Apple Extreme Wireless Router that 30 Laptops use. I also have 25 VOIP phones and 10 Desktops that are on an unmanaged switch which I want to convert to the new SG200-50.
I'm using a Dell computer CPU i7 8 gig of ram. It is wired in to the router. Why does it take so long to log into the router and bring up the different pages in the settings. I have never seen a router take so long. I have not updated the firmware version 2.02NA. I have not upgraded it yet. oh I have a cable connection. When I surf the web the pages come-up fast.
View 13 Replies View RelatedToday i has tryed to update the firmware of my DIR-655 router, but in the screen under the administrative tools menu there is nothing to use.
how do I update the firmware and bring up all the necessary tools?Dir-655 works because they are connected to the internet and manages the wireless network.
I am trying to connect a 6509 switch to a 4503-E switch using single mode dark fiber over a distance of less than half a mile. Although a routine task, it does not work..We have a care 6509 switch where we concentrate all of our dark fiber connections for our remote sites. The 6509 switch already has 30 remote sites, most of them with 4503-E switches, connected in this way therefore it is a tested scenario. For the connections we use the GLC-LH-SM SFPs on both switches. Out of these 30 sites we had a similar problem with two of them, which we solved with the use of CWDM SFPs. With the CWDMs the fiber came up right away. However, I cannot keep using this solution because it is way too expensive! I had the losses of the fiber measured end-to-end and they are negligible (>0.5 dB).
In this latest case, like I said, we could not bring the connection up between the core 6509 switch and the 4503-E switch using the GLC-LH-SM SFPs. I then replaced the 4503-E switch with a 3560 and the link came up! Then I tried using a CWDM-SFP in the 4503-E, while keeping the GLC-LH-SM SFP in the 6509 and the link came alive again! Of course we already tried replacing the fiber patch cords with no luck. [code] I find it very weird for the link to work with the 3560 or with a CWDM in the 4503 but NOT with the SFP in the 4503!
I have two 3825's. Each has it's own ISP connection. Nat is configued for both. They have an ethernet connection between them and I'm running OSPF between the two so the routes propogate. I have qty 11 Dialer interfaces configured on each router (each router has an exact copy of the other routers dialer interface). However, I only want the Dialers up if the ISP connection on the mated router goes down. Much like HSRP I need one to preempt and be active if both ISP connections are up. When one goes down the other Dialers must come up. Each dialer sends a Dynamic DNS host name and IP address pair to DynDNS.org. So I cannot have both up otherwise the DNS names will bounce between ISP#1's IP address and ISP#2's IP address (back and forth). Let me know if any option exists to make this happen. As an aside the ISP's are providing me DHCP addresses so I cannot work off of an IP, it has to be the physical interface (i.e. Gi0/0).
View 1 Replies View RelatedI need WIFI inside a giant steel Quanset hut. There is a good signal right outside. Is there a way to do this with one device? I was wondering if I could put one of the antennas of a WRT54G through a hole to the outside and then set it in repeater mode. Theory being it would use the outside antenna to pickup the signal and the inside antenna to broadcast.
View 2 Replies View RelatedI have a gateway to gateway vpn (home-office) working fine for almost an year btw 2 wrvs4400n routers, This morning, the VPN tunnel was down. I clicked "Connect" from the web based interface, but it does not reconnect.
I tried setting up a new tunnel using the VPN setup wizard, but it says it can't connect to the remote router. Which is strange, since I can ping there normally.
Is it possible to have a site-to-site IPSEC tunnel between 2 identical RV110W routers?I basically want one of them to initiate a secure tunnel with the second so that computers from one router subnet see the computers from the other router subnet.
View 3 Replies View Relatedthe RV110W IPSEC site-to-site tunnel, are there necessary 2 x public IPs for it to work, or only 1 public IP is enough? [code]If it works with 1 public ip, the "CLIENT" RV110W configuration should be straightforward (in Advanced VPN SetupRemote Endpoint i fill in the dyndns address?), but how do i setup "HOST" RV110W?
View 2 Replies View RelatedIs it possible to configure an IPSEC GRE tunnel with RIP on an SRP527w? I see RIP, GRE & IPSEC are all possible.. But I'm not sure about them all together securing the GRE tunnel??
I basically want to do this with the SRW routers not native IOS. Single head end hub & spoke.
I'm trying to setup a VPN between an RV042 V3 and an RV082 V2 router. They get connected but no traffic gets through the tunnel. I tried with and without firewall,DPD, Keepalive, forward secrecy but nothing worked. What should I do? I don't want to throw out the V2 routers. V3 to V3 connects fine.
View 1 Replies View Related