Routers / Switches :: 2 Routers On Same Subnet With DD-WRT VPN Tunnel On Second?
Mar 13, 2012
How to set up a home network with 2 routers, where R1 acts as the DHCP server and R2 is basically a switch, connected LAN to LAN and everything is on the same subnet. Currently I have a different setup:Both routers have the DHCP server enabled and I connect R2's WAN port to R1 LAN. Therefore I have 2 subnets. Now my special requirement is that R2 is a DD-WRT router, which establishes a VPN connection to StrongVPN, so that all internet traffic via R2 is encrypted and goes through the StrongVPN server. Now my question:If I change my router setup to the same subnet, meaning R2 connects LAN to R1 LAN and I disable DHCP server on R2, will R2 still be able to establish the VPN connection?
View 5 Replies
ADVERTISEMENT
Jun 12, 2012
Is there any way to setup an IPSEC tunnel to be able to go from my subnet, 192.168.75.x and be able to reach anything on the other side of the tunnel, 192.168.X.X?
View 5 Replies
View Related
Apr 21, 2012
I have two offices connected with an IPSEC VPN tunnel using RV220W routers. The Tunnel works fine for local users between the two sites(Site 1:10.0.0.x; site 2 is 10.0.2.x). I have also set up PPTP users for remote access. PPTP users that connect to site 1 cannot access site 2 and vice versa. The PPTP users have no trouble accessing the resources on the site that they connect to. I have tried activating RIP and adding various static routes with no success. If I PPTP connect to site 1 and I tracert to an IP address on site 2 the route goes to the site 1 router and then goes to the internet(connected to the site 1 router) where it stops.
View 2 Replies
View Related
May 8, 2011
what is subnet mask of 10.2.1.3/22
View 1 Replies
View Related
Jan 16, 2011
how to subnet a class B IP address?I have a homework, I don't know how to subnet a class B.
View 2 Replies
View Related
Apr 18, 2012
Following instructions on How to add a 2nd router to network.This error will not let me complete and save the definition. Changed 2nd router IP address to 192.168.1.2 static, disabled DHCP, added 1st router IP as default gateway, set subnet mask to same as 1st router. Problem occurs in next frame called 'Network Setup' it is requiring a 'router IP' & subnet mask again and will not accept either the 1st or 2nd router IP address - gives the "IP equals subnet please correct" error or "LAN & WAN IP addresses are identical.
View 11 Replies
View Related
Mar 7, 2012
Two networks. NetA: IP subnetID 10.101.x.x subnet 255.255.0.0. Devices have static-assigned IP's. Only DHCP runs on wireless AP for wireless client connection. IP addressing scheme set by hardware vendor, so not under my control. NetB: IP subnet 10.x.x.x subnet 255.0.0.0. Campus LAN and also not under my control. DHCP supplied addressing. how to get NetA devices to route to NetB?I would like to be able to provide Internet access (via NetB)to NetA devices.
View 7 Replies
View Related
Sep 25, 2012
I have an issue with some traffic routing:
Machine A | Machine B (Win 2008 R2) | Machine C
Start: 192.168.5.9 > 192.168.5.5 (NIC 1) - 10.14.137.130 (NIC 2) > 10.14.137.128So the question is how do i get traffic from Machine A to Machine C. I've tried various 'Route ADD' cmds but no luck so far. So was hoping someone out there could shed some light for me?Machine B is a AD/DNS and can talk to the entire 10.14.137.x range but has no forwarders set up in DNS. And does not act as a AD/DNS server for the 10.14.137.x range. It fills these roles only for the 192.1668.5.x range.
View 3 Replies
View Related
Jun 23, 2011
I have a supplier which i need to connect a site to site ipsec vpn connection to (from a draytek router). I have already done this on our main site with no problems using the local ip details of 192.168.1.0 and subnet 255.255.255.0 however i need to do the same on our DR site which uses the ip details of 10.1.0.0 and subnet of 255.255.0.0. Our supplier told me the 255.255.0.0 is already used at there end by a different customer so we are unable to connect the vpn and communicate (in theroy we can connect but our supplier cannot reply). We can setup a connection to another spare server on a different address using a different subnet but effectivly this would mean that communication would stop at that server and communcation to the overall network or specific server the supplier needs access to (on the 10.1.0.0 255.255.0.0 network) is not possible. I was thinking maybe an internal vpn server to server connection through win server may do it, 2 nic cards or routes in the server routing table but this all seems a bit messy. Our network consits of win 2003 and 2008 R2 servers and is basic network with modem-vpnfirewall-switch and devices on the internal network connecting to the switch.
View 5 Replies
View Related
Oct 17, 2012
I am using a Cisco RV110W (Firmware 1.2.09) in a branch and I would like to create a VPN Tunnel to another site that has a Cisco RV042 (firmware v4.2.1.02)
What would be the correct Configuration? the current configuration I am using is
in the RV042 i am using
Check Enable
Local Group Setup
Local Security Gateway Type : IP Only
IP Address : RV042 Pulbic IP address
[Code].....
View 3 Replies
View Related
Jul 24, 2012
Environment :linksys wrt300n v1.1 which can have ddwrt-mega. Willing to tunnel all lan's outbound traffic through an ssh tunnel.
View 2 Replies
View Related
Jan 2, 2013
If your wireless indicator is flashing red when you discover the smurf, it can mean that someone has tried to logon with an incorrect password. this is not necessarily an attack, it could be someone you have allowed access too, who has forgotten the password? In this case entering the correct password will solve the problem.However putting your own MAC address into the filter will simply block your own machine.
View 6 Replies
View Related
May 24, 2012
For my work I am looking to create wireless capabilities to remote locations. To do this we are using a standard modem/router that is connected to an Engenius (802.11b/g) wireless outdoor radio connected to a dish antenna. We are able to go to locations (3+km) and then with a corresponding receiving antenna (using LoS), receive the Internet and connect both to computers at the transmitting point as well as to the WWW. The problem exists is that we want to employ a series of routers at the receiving end that would be able to carry the transmission to a different location (relatively close), due to the fact that some of the locations do not have line of sight to the antennas. We are using Encore routers, model # ENHWI-N3. When we connect the radio's Ethernet into the routers WAN reciever, we can connect to the Internet with a computer. The problem exists is we want to pass that connection over to a second router (R2). This connection is done when the routers are on access points set to a WDS function with R1 having R2's mac address and vice versa. Both routers are set to channel 1. Even when the routers are seperated by distances >50m a computer plugged into R2 can see a computer plugged into R1. Files can be transferred between the 2 computers wirelessly at speed around 3 mbps. However computer 2 on R2 can not connect to the WWW. This router features a spot that lights up if it has Internet access and R1's is lit up but R2's is not. How do we transfer the Internet and not just a LAN from R1 to R2 so it can be accessed further away from the point of the radio and antenna equipment. This setup has also been used where R2 is hardwired to R3. At R3 we change the channel to 11, and then connect through that with mac addresses wirelessly to 4th router. If comp is in R4 and far away it can still access and file share from comp at R1.*edit the ip address for the routers exist all on 192.168.1.xxx If the 3rd number is different between routers would this make a difference?
View 1 Replies
View Related
May 26, 2011
everything was all good, my brother went crazy and unplugged everything.it effects our house phone too, that could be the problem.i just dont know what wires went where. all the wires are the same color.but i know which is which. just again, dont know where.i would like to get it done before he gets home later on.
View 1 Replies
View Related
Mar 13, 2013
Is it possible to have a site-to-site IPSEC tunnel between 2 identical RV110W routers?I basically want one of them to initiate a secure tunnel with the second so that computers from one router subnet see the computers from the other router subnet.
View 3 Replies
View Related
May 19, 2013
the RV110W IPSEC site-to-site tunnel, are there necessary 2 x public IPs for it to work, or only 1 public IP is enough? [code]If it works with 1 public ip, the "CLIENT" RV110W configuration should be straightforward (in Advanced VPN SetupRemote Endpoint i fill in the dyndns address?), but how do i setup "HOST" RV110W?
View 2 Replies
View Related
Dec 31, 2012
The first router is wired to the DSL modem and works just fine as an access point with Internet access. The second router is wired from the first router using one of the 4 ports on both router hubs. The second router is visible but has no Internet. How to configure the second router regarding DHCP, LAN, WAN, DNS etc.
View 3 Replies
View Related
Nov 28, 2011
What are procedures to deactivate di-604+di-704 routers+make the repeaters,connecting each of them,in a wired fashion,to my Belkin wireless N router?
View 1 Replies
View Related
Mar 10, 2012
how to installs 3 router with same password
View 2 Replies
View Related
Jun 13, 2011
modem
........ |
........ |
----switch-----
|................ |
|................ |
Router 1.... Router 2
|..................... |
|..................... |
Computer 1.....Computer 2
......................Computer 3 Router 1 points to a VPNRouter 2 access to the internetComputer 3 needs to access router 1 (VPN). Both Computer 2 and 3 are in a different room than computer 1, and router 1. Computer 2 is networked via cat5e to router 2.Is is possible to have Computer 2 and 3 share the cat5e, yet access different routers?
View 5 Replies
View Related
Apr 30, 2011
Can I connect 2 routers to one phone line so that I can receive a wireless internet connection throughout my house?
View 1 Replies
View Related
Jun 29, 2012
I need to print to a printer in with a static IP on a different subnet from a host on a different subnet using DHCP.
View 1 Replies
View Related
Sep 8, 2012
I'm trying to connect two routers and create a subnet but failing due to a little knowledge but no real understanding! I've read the ultimate setup thread loads of times but can't get my setup to work.
Here's the setup I'm trying to build:
Internet -> Master ADSL modem/router (No NAT, no DHCP) -> Slave cable router (NAT, DHCP)
I want to connect 3 Xboxes to the master router with external IPs to avoid the whole "moderate/strict" NAT nightmare. Then I'll connect everything else (PCs, Macs, wireless devices etc) to the Slave router which will assign IP addresses and do the NAT thing. Both routers are Netgear N150s (master is ADSL, slave is Cable).
Here's what I've tried so far:
Master router:
All IP addresses supplied by ISP
Internet IP: xxx.68.160.143
DNS: xxx.xxx.3.xxx and xxx.xxx.6.xxx
Router IP: xxx.68.160.142
[Code].....
View 1 Replies
View Related
Apr 30, 2012
I'm trying to set up 2 subnet with two RV042 routers. One router will act as a gateway and both WAN ports will be used by two different isp connection. The first router (gateway) LAN IP will be 192.168.0.1/24. I would also like to set up another router behind the gateway with with separate subnet 192.168.1.X/24. And I would like clients on the 192.168.1.x subnet to use the internet through the gateway router and clients on the 192.168.0.x subnet to access resources on the 192.168.1.x subnet. Am I able to do this with two RV042?
View 6 Replies
View Related
Nov 12, 2012
I would like to set the subnet mask off the lan to 255.255.240.0 but the selection menu do not allow to do it.
View 8 Replies
View Related
Nov 8, 2012
I'm trying to setup this router with my IP range 192.168.100.1 to 192.168.101.254 but if I try to enter a subnet mask other than 255.255.255.0 I get the error - Invalid subnet mask. It should be 255 for given class of IP address at 255.255.xxx.0.
Every other device on my network allows that subnet mask, why not this router, it's stopping access from my 192.168.101.x devices.
View 5 Replies
View Related
Jul 10, 2012
I have RV042 Router, I'm using only one Internet conection, I'm using IP group like this 192.168.95.x, my DHCP setting use 192.168.95.120 to 192.168.95.240, but in this time I have 245 workstations (may be I will have 25 additionals workstations) and some times I see IP conflict message in my current work stations.
I had read about SUBNET like response about my problem, but I'm not sure about that and how to make subnet with my RV042.
View 7 Replies
View Related
Feb 12, 2012
I'm wanting to use the SRP527W (from Telstra) to route a block of assigned internet addresses (/29) over the WAN internet IP address. Is this possible on the 527W, or does it only do NAT routing?
View 6 Replies
View Related
Dec 2, 2012
We connected to locations to the RV042 by setting up 2 Gateway - to - Gateway VPNs - both locations can communicate with the RV042 and devices within the local LAN of the RV042 - however at the moment it is not possible to send traffic from 1st VPN Location to the 2nd VPN location
View 1 Replies
View Related
Aug 24, 2011
I have a RV042 with multiple subnet, 192.168.10.0 and 192.168.9.0. 192.168.10.0 is assigned to the LAN, 192.168.9.0 is created under multiple subnet. Both subnet can access Internet by accessing IP address, but 192.168.9.0 cannot access Internet by using host name. It looks like DNS is not working for the 9.0 network.
View 1 Replies
View Related
Apr 26, 2012
i want to ask if i can link two routers while they are totally separated of each other over the internet to make a large LAN the two routers are TP link?
View 5 Replies
View Related
Mar 8, 2011
How do i connect two internet routers to one IP address range?I currently have one broadband router connected on 172.16.0.3 subnet 255.255.0.0, I have a second line which is a copper ethernet EFM 2Mb line connected using a Cisco 1800 router configured on 172.16.0.254 subnet 255.255.255.0, no DHCP is configured on either router. the dhcp is provided by a windows 2003 server on our LAN which is also configured on the same LAN IP range. if i connect the Cisco router into the same switch as the broadband router my network devices stop working and dont respond.
If i check the broadband router it shows all the connections to it as having the same MAC address as the Cisco router?? if i disconnect the Cisco router everything returns back to normal and works perfectly.What I want to achieve is to be able to run both routers on the same LAN to provide internet access by configuring the pc's to route through a specific router. the DHCP I want to stay routed through my original broadband line. at the same time i want all pc's to access to the lan devices (ie. servers and printers) what the correct configuration would be for the two internet routers would be?
View 5 Replies
View Related
Jul 26, 2012
I have one cisco 2851 router and one watchguare firewal currently being used as the main router. I want to connect the cisco as a secondary router on the same network.
View 10 Replies
View Related
