We connected to locations to the RV042 by setting up 2 Gateway - to - Gateway VPNs - both locations can communicate with the RV042 and devices within the local LAN of the RV042 - however at the moment it is not possible to send traffic from 1st VPN Location to the 2nd VPN location
View 1 RepliesI'm trying to set up 2 subnet with two RV042 routers. One router will act as a gateway and both WAN ports will be used by two different isp connection. The first router (gateway) LAN IP will be 192.168.0.1/24. I would also like to set up another router behind the gateway with with separate subnet 192.168.1.X/24. And I would like clients on the 192.168.1.x subnet to use the internet through the gateway router and clients on the 192.168.0.x subnet to access resources on the 192.168.1.x subnet. Am I able to do this with two RV042?
View 6 Replies View RelatedI have RV042 Router, I'm using only one Internet conection, I'm using IP group like this 192.168.95.x, my DHCP setting use 192.168.95.120 to 192.168.95.240, but in this time I have 245 workstations (may be I will have 25 additionals workstations) and some times I see IP conflict message in my current work stations.
I had read about SUBNET like response about my problem, but I'm not sure about that and how to make subnet with my RV042.
I have a RV042 with multiple subnet, 192.168.10.0 and 192.168.9.0. 192.168.10.0 is assigned to the LAN, 192.168.9.0 is created under multiple subnet. Both subnet can access Internet by accessing IP address, but 192.168.9.0 cannot access Internet by using host name. It looks like DNS is not working for the 9.0 network.
View 1 Replies View RelatedSmall office, 2 RV042, 2 DSL connections. 1 is used striclty for the business side, and the other is for our CCTV network. They also have seperate DSL connections as we have 2 external IP address for clients to connect remotely. We don't want to take away our exisring setup, but would like to bridge both networks so a few of our internal clients can connect to our CCTV network and use some of the devices. Right now they come in on VPN but its not as fast.Is this doable without adding additional hardware? Both networks need DHCP enable as well.
Breakdown:
DSL 1
|
RV042
|
192.168.20.X
|| Would like to somehow join the 2 networks together.|
DSL 2
|
RV042
|
192.168.40.X
I'd like to set each individual LAN port with different address i.e. LAN 1 192.168.1.1 and LAN 2 10.1.1.1 instead of using the multiple subnet feature and having all ports replying for the addresses created.
View 3 Replies View RelatedI have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). It works fine when I'm on a different network like 3G or someone else's Wifi network (192.168.11.X).
View 1 Replies View Relatedmy RV042 is not able to propperly update my ddns. If you try to resolve my dyndns subnet kitus-network.dyndns.org you will get 192.168.0.2. How can I make the router update my ddns with the real public ip rather than the private ip it "sees" on the WAN interface?
View 5 Replies View RelatedI have 2 questions to confirm and/or get direction on how to modify.
1) is there a way to get around the (seemingly arbitrary) class C (slash 24+) subnet restriction for the primary/main IP address for the internal LAN?
(I realize I can setup multiple internal subnets but that also seems to introduce restrictions for port ‘forwarding’ and ‘one-to-one NAT’ use because those features seem to be restricted to the primary/main IP subnet)
2) it seems like all traffic is passed to the host on the internal side of a ‘One-to-One NAT’ regardeless of the firewall rules in place, is that what is be expected?
I have an issue with some traffic routing:
Machine A | Machine B (Win 2008 R2) | Machine C
Start: 192.168.5.9 > 192.168.5.5 (NIC 1) - 10.14.137.130 (NIC 2) > 10.14.137.128So the question is how do i get traffic from Machine A to Machine C. I've tried various 'Route ADD' cmds but no luck so far. So was hoping someone out there could shed some light for me?Machine B is a AD/DNS and can talk to the entire 10.14.137.x range but has no forwarders set up in DNS. And does not act as a AD/DNS server for the 10.14.137.x range. It fills these roles only for the 192.1668.5.x range.
i am using RV042 router, i have configured DMZ in this, DMZ is not passing the traffic, i am able to ping the DMZ ip from the server. but the server is not getting the Internet.
View 1 Replies View RelatedWe have a managed service provider voip network that requires us to use our own router for the data network. We wanted to use the RV042 for it's easy vpn setup. After installing it worked great for about 10 min. then the WAN port stopped passing traffic. 3 min. later it started working again. We tested the RV042 on a different network and it works fine. We tested an older Pix on the managed network and that works fine. But the RV042 will not work on the managed service provider voip network. The service provider says that on their end it shows our WAN port going up and down.
View 1 Replies View RelatedI'm having some problems blocking IP blocks. I have several blocks of IP's that I want blocked.I want to block 77.0.0.0/8 from communicating with a server on my lan.So I make a rule in the RV042 to deny all traffic from 77.0.0.0 to 77.255.255.255, source wan1, destination lan, my server's ip,As soon as I move that rule above the traffic forwarding rules I have created, no traffic moves in or out via the wan interface. It seems to just cut off all traffic.
View 2 Replies View RelatedReplaced an older RV042 that had damage from lightning. The new RV042 is V03 with firmware 4.0.0.7. This router supports 7 branch offices using site-to-site VPN to other RV042 routers. After connecting the new RV042 at the main office, three of the branch offices had very slow response over the VPN tunnel. I disabled the firewall on the new RV042 and the problem resolved. The three branches with the problem have Windows 7 systems and the other 4 have Windows XP. I confirmed that the Windows firewall was disabled on the Windows 7 systems.I did try leaving the firewall enabled and disabling SPI, but that didn't work. Have to have firewall disabled to resolve the problem. I would not expect the firewall on the main office RV042 to affect VPN tunnel traffic, but apparently it does. Do we need specific access rules to fix the issue. It works fine with firewall disbaled, but I'd be more comfortable with it enabled.
View 2 Replies View RelatedI have an RV042 router and I'm looking to monitor the total upstream and downstream traffic from within the router.
I know there is tons of software that I can put on a network computer to monitor traffic, but is there any software that I can put on the router itself that will monitor the traffic from within the router?
We have offices in USA and Venezuela.In our USA office we have a RV042 router and in Venezuela we have a RV082 router.We have connected a VPN tunnel (gateway-to-gateway) between both offices.
The point is:How could we redirect the internet traffic from our Venezuela office (RV082) to the USA Office (RV042) to navigate using USA public IP's?
The reason for this is that we need to use online streaming services which are only available for IP's from USA and we can't use them from the Venezuelan IP's.
We can not use the PPTP option since the equipment which will use the streaming services (like hulu, crackle, etc.) in Venezuela is a Google TV device which doesn't allow the configuration of proxy navegation or PPTP VPN connections itself. That's the reason why we need to do that through the routers.
We have a VOIP system from AT&T with T1 internet access. I have a RV042 setup as the default gateway for the network and the router randomly (usually over the weekend loses the internet). I have updated to the latest firmware and have check all logs on the server. When the internet access goes down we can still access the internal network. I have been power-cycling the router and then everything works fine. Is there a known issue with this router radomly blocking internet access in or out? This device should remain working at all times so that our remote users can access the company network.
View 0 Replies View RelatedI have an RV042. I understand and have created the services I need. The documentation is just not clear on how to direct traffic for these services to a specific wan port.
Can this even be done with this router? If so, the how? Use rate control or priority? Does checking a wan port mean that it will only go through that port?
I have a RV042 (firmware 1.3.13.02-tm). Is it possible to configure so traffic from a specific domain (incl. its sub-domains) is directed exclusively to one WAN port?
View 10 Replies View RelatedI wonder if I can have a RV042 VPN Tunnel to a RV082, and in the RV082 block all traffic to the internet that comes form the PCs that are behind the RV042.
Remote PC -> RV042 -> VPN -> RV082 -> RV082 Firewall (block internet traffice, allow intranet traffic)
I configured ASA5520 and RV042 for site-to-site IPSec VPN tunnel.Tunnel get connected, but no ping, no traffic between both end network.
Network:
=======
192.168.113.0/24----------192.168.113.6 -ASA--------public, static IP address------Cisco 2821--------Internet
192.168.10.0/24-----------192.168.10.1 -RV042-----public, static IP address------Cisco 2821--------Internet
ASA5520 config:
----------------------
name 192.168.10.0 VPN
!
interface GigabitEthernet0/1
nameif NET
security-level 100
ip address 192.168.113.6 255.255.255.0
[code]....
I am trying to set up my router to grant http traffic a minimum bandwidth of - for example - 5,000 kBit (if there is any http traffic).
So I set http min. rate to 5,000 while I set nntp min. rate to 1 However, when I run nntp downloads on several connections (e.g. 10) my single http download never goes above 1,000 kBit. Without any other connections I reach 8,000 kBit.
I am using a single 12 MBit line.
I have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). It works fine when I'm on a different network like 3G or someone else's Wifi network (192.168.11.X).
View 1 Replies View RelatedI would like to the the RV042 for a one to one NAT, but I need it to NAT to an address that is not on it's local subnet. I have it routing properly to the address, but web interface only allows adding an IP on the local subnet. Is there a way around that?
View 1 Replies View RelatedI’ve configured a small WLAN for a school that wants to have wireless network access for their staff as well as for guests doing presentations. They want the staff to have access to everything on the 192.168.1.0 /24 network as well as the Internet. They want the guests to only have access to the Internet. I have attached a picture which shows how the network has been configured with 4 Cisco AP1242G AP’s attached to a Cisco SF302-08MP PoE switch and then to a Symantec Security Gateway to the Internet.
I can authenticate wirelessly to the STAFF SSID and ping anything on the 192.168.1.0 /24 network and access the Internet.I can authenticate wirelessly to the GUEST SSID and ping anything on the 172.16.1.0 /24 network, but not anything on the 192.168.1.0 /24 network (which is what we want). However, when on the GUEST network you can’t access the Internet. I added a default route to the Cisco 302-08MP switch to 192.168.1.1 (Symantec firewall) thinking that would forward the traffic from 172.16.1.0 /24 to the Symantec firewall out to the Internet, but that isn’t working.How would I go about getting the traffic from 172.16.1.0 /24 to hit the Symantec firewall and the Internet, without hitting anything else on 192.168.1.0 /24? Do I need to put the Symantec firewall in a different subnet like 192.168.2.0 /24? Am I missing anything else?I’ve worked with Extreme Networks & HP / 3Com CLI in the past, but never with Cisco and never with web based management
I am facing problem with ACE configuration. I want to redirect 443 traffic to my Proxy Server. But I am not able to do this. I want to redirect only subnet 192.168.80.0/24..Then only it is working but I dont have to have this policy to be applied on all the users only one subnet I want to have under HTTPS policy.
how can I apply the policy only on specific subnet so that port 443 traffic can be redirect and rest of all subnets can go direclty to Internet.
I am having touble with a NAT concept. What I have is a 3rd party software VPN product that basically tunnels encapsulated traffic to/from a server sitting inside the network. Right now this traffic utiluizes a physical interface on the ASA5510, but I need the interface for another project.
What I have is this:
Internet<----->ASA<-->router<-->4507(layer3)
| |
| |-Vlan1
[Code]......
I have a two RV042 VPN Router, I successfully connected the IPSEC tunnel. I cannot route Traffic in the tunnel. See the diagram.
MAIN Network
10.252.x.x
-------------->
FIREWALL
a.a.a.1
INTERNET
RV042a WANa <<------------------------------->> WANb RV042b
a.a.a.2 b.b.b.b
In this manner the network of b.b.b.b wil connect to the Main Network 10.252.x.x, unfortunately I can't pass traffic to RV042b going to RV042a. Everytime I trace the route, the traffic goes outside the Internet not to RV042a.
I just acquire the RV042.We have a DSL [WAN1 :download good, bad uplaod] and an SDSL line 4MB OVH [WAN2].
Receive all downstream traffic to WAN1Send email upstream traffic to WAN1Send upstream traffic to OVH and guarantee good bandwidth to 10 TSE access and webex traffic
I built the following rules:
The problem ... nothing works ... the downstream traffic comes from WAN2 and upload on WAN1 or WAN2.
How to set up a home network with 2 routers, where R1 acts as the DHCP server and R2 is basically a switch, connected LAN to LAN and everything is on the same subnet. Currently I have a different setup:Both routers have the DHCP server enabled and I connect R2's WAN port to R1 LAN. Therefore I have 2 subnets. Now my special requirement is that R2 is a DD-WRT router, which establishes a VPN connection to StrongVPN, so that all internet traffic via R2 is encrypted and goes through the StrongVPN server. Now my question:If I change my router setup to the same subnet, meaning R2 connects LAN to R1 LAN and I disable DHCP server on R2, will R2 still be able to establish the VPN connection?
View 5 Replies View Relatedlink where to download user manual and/or Technical manual for Linksys RV042 Dual WAN VPN RouterDoes the Linksys RV042 Dual WAN VPN Router AGGREGATE the bandwidth of the two WAN Ports for LAN use or how does it operate?Does it manage traffic on Layer 7 (Application Layer);can i configure say, yahoo messenger traffic to take priority over youtube traffic or http traffic over download/upload traffic or such?Does it have DYNAMIC bandwidth allocation/management feature?Can i Guaranteed Bandwidth Allocation for a particular user or IP Address?Does it have TCP Ack Prioritization feature?Can i direct site(s) traffic,say cisco.com and/or port or service to use a particular WAN port?If this product cannot handle this features?
View 1 Replies View RelatedIn our USA office we have a RV042 router and in Venezuela we have a RV082 router. We have connected a VPN tunnel (gateway-to-gateway) between both offices.
The point is: How could we redirect the internet traffic from our Venezuela office (RV082) to the USA Office (RV042) to navigate using USA public IP's?
The reason for this is that we need to use online streaming services which are only available for IP's from USA and we can't use them from the Venezuelan IP's.
We can not use the PPTP option since the equipment which will use the streaming services (like hulu, crackle, etc.) in Venezuela is a Google TV device which doesn't allow the configuration of proxy navegation or PPTP VPN connections itself. That's the reason why we need to do that through the routers.
I have an RV042 router and I'm looking to monitor the total upstream and downstream traffic from within the router. I know there is tons of software that I can put on a netowrk computer to monitor traffic, but is there any software that I can put on the router itself that will monitor the traffic from within the router?
View 1 Replies View Related