Cisco Routers :: ASA5520 And RV042 - Tunnel Get Connected But No Ping / No Traffic Between Both End Network
Sep 13, 2011
I configured ASA5520 and RV042 for site-to-site IPSec VPN tunnel.Tunnel get connected, but no ping, no traffic between both end network.
Network:
=======
192.168.113.0/24----------192.168.113.6 -ASA--------public, static IP address------Cisco 2821--------Internet
192.168.10.0/24-----------192.168.10.1 -RV042-----public, static IP address------Cisco 2821--------Internet
ASA5520 config:
----------------------
name 192.168.10.0 VPN
!
interface GigabitEthernet0/1
nameif NET
security-level 100
ip address 192.168.113.6 255.255.255.0
[code]....
View 5 Replies
ADVERTISEMENT
Sep 14, 2012
I have created an IPSEC VPN tunnel using a Cisco ASA5520 (corporate) to a Cisco SRP541W (remote). The corporate subnet is 10.1.0.0/16, and the remote subnet is 192.168.1.0/24. From the remote subnet, I can ping anything on the 10.1.0.0 corporate network, but I cannot ping from the corporate network to the remote subnet. At first I thought this was something obvious, perhaps an incorrect acl or something easy on the corporate firewall. However, we have several other vpn tunnels established, all set up the same, and they work just fine. After looking at it a bit more closely, if I ping the remote subnet I see the hit counter increment by one each time, which leads me to believe that traffic is in fact being routed properly.Now I'm thinking that something in the remote SRP541W that is not allowing icmp traffic, but I can't find it anywhere. To be honest I have never used this type of firewall before, they have all been Cisco PIX501/506e and ASA5500 models.
View 2 Replies
View Related
Aug 5, 2011
I have a RVS4000 at one location and a second RVS4000 at home. I have established an IPSec VPN tunnel between them and it is UP. I can ping the routers from each end no problem. I can ping the IPs listed in the "Local Group Setup" and the "Remote Group Setup" from both ends no problem. I can even open up a shared resource from a Win 7 machine (e.g. by typing \10.10.10.100 in start-run from a computer on my home network).
But - i can't ping anything else on one network from the other. What gives? I need to access a 10.10.10.101 machine but can't even ping it.
- both RVS4000 boxes have latest firmware (V1.3.3.5)
- home RVS4000 setup with IP 10.10.11.1
- home network has a server with IP 10.10.11.20
- other location RVS4000 setup with IP 10.10.10.1
- other location server setup with IP 10.10.10.100
Tunnel settings on home RVS4000 (the other location properly mirror these).
- Local Security Gateway Type : IP Only
- Local Security Group Type : Subnet
[code]....
View 2 Replies
View Related
Jun 6, 2011
I have a two RV042 VPN Router, I successfully connected the IPSEC tunnel. I cannot route Traffic in the tunnel. See the diagram.
MAIN Network
10.252.x.x
-------------->
FIREWALL
a.a.a.1
INTERNET
RV042a WANa <<------------------------------->> WANb RV042b
a.a.a.2 b.b.b.b
In this manner the network of b.b.b.b wil connect to the Main Network 10.252.x.x, unfortunately I can't pass traffic to RV042b going to RV042a. Everytime I trace the route, the traffic goes outside the Internet not to RV042a.
View 1 Replies
View Related
Nov 26, 2011
I have an RV042 using Quick VPN to connect to a remote network. I have port 1723 forwarded to a static IP address on a Windows 7 Pro 64 bit PC. I can establish the VPN and ping a printer but not the Win 7 PC. I can not acccess any shares on the pc via the IP address. It has Norton Antivirus and Windows Firewall. This remote PC replaced a Windows xp PC that allowed access to the shares. I have tried access with a Windows XP Pro and Windows Vista Home Premium PC. Neither have worked.
View 1 Replies
View Related
Jul 24, 2012
Environment :linksys wrt300n v1.1 which can have ddwrt-mega. Willing to tunnel all lan's outbound traffic through an ssh tunnel.
View 2 Replies
View Related
Oct 28, 2011
I have recently purchased a E4200 i have flashed it with the latest Firmware 1.0.03 and Hard Reset the Router so the Media issue was resolved i was having. After upgrading the firmware to the latest version my Nortel VPN IPSEC Client no longer will work. The tunnel is connected and it passes traffic for about 15 seconds then nothing. The connection remains connected but no traffic passes cant ping across tunnel. I have checked all the settings and VPN - IPSEC - Passthru is enabled. I have put the client in DMZ mode and tried that same thing.
View 7 Replies
View Related
Apr 10, 2012
We have an ASA5520 version 8.3(1) We have an existing VPN tunnel between us and our partner site. We need to add a new vlan to our existing VPN tunnel.
Where do we need to add the new vlan to in ASDM interface? Looking through using ASDM, I found 3 places.
Site-to-Site VPN:
1) Connection profiles
2) Advanced > crypto maps
3) ACL Manager
View 5 Replies
View Related
May 31, 2011
Our firewall expert has gone off on long term illness leave and I am trying to pick up the pieces :-(
We have an ASA 5520 (local office) talking to another ASA (remote office) via a VPN Tunnel.
My 1st problem is that I cannot ping from my inside network (local) to the outside interface of my remote ASA.
My 2nd is that I have debug enabled on my rules but am not logging anything.
View 1 Replies
View Related
Dec 16, 2011
how to establish tunnel between rvs 4000 and rv042 ?
View 2 Replies
View Related
Dec 14, 2011
here's my setup :
office 1 :
rv042 hw3
ISP:Obtain an IP automatically
office 2 :
rv042 hw3
ISP:PPPoE
VPN tunnel between both rv042, everything's fine but when i try to ssh from office 2 to an office 1's server, my connection drops.
When it drops, i can still ping pc in office 1, this is really strange!if i change the office 2 ISP to another provider (obtain an IP automatically) everything's ok !
i try to use another PPPoE ISP for office 2 and it's doing the same thing!I've also tried other rv042 in both locations with the same setup and it's doing the same thing, so it's not a router issue.
i've tried older firmware and it's doing the same thing, so it's not a firmware issue!
View 3 Replies
View Related
Jun 27, 2012
I have configured a VPN tunnel between two remote locations using static IP addresses on two RV042 routers. The tunnel seems to work but the problem is that when the two hosts attempt to ping each other only one can successfully ping. One PC with IP address 192.168.1.100 can ping across the network but the second PC with IP address 192.168.2.100 cannot. These are laptops seperate from the intranet used to test the tunnel. Someone had suggested NAT may be the issue so I enabled NAT Transverse on the routers but still no luck. The following is the results from a ping test.
PC 1
ping 192.168.2.1
Pinging 192.168.2.1 with 32 bytes of data:
Reply from 192.168.2.1: bytes=32 time=116ms TTL=63
[Code] ......
View 1 Replies
View Related
Aug 5, 2011
We have 4 RV 042 routers and cisco router at HQ, we have Site to Site VPN tunnels in between, All branch offices are connected to HQ via S2S VPN tunnels
10.10.1.0/ 24 HQ
10.10.2.0/24 Branch 1
10.10.3.0/24 Branch 2
10.10.4.0/24 Branch 3
10.10.5.0/24 Branch 4
now lets say i am branch 1, i can access 10.10.1.0/24 network but cant access 10.10.5.0/24 network, means i dont have branch to branch connection, it should be through HQ, means my RV042 at brnach should fwd all traffic to HQ for another branches also. Under VPN tunnel if i try to configure remote destination 10.10.0.0/21 its not allowing me it says network overlaping with local network, how i can sole it, I know how to do in cisco, we can permit those networks in access lists.
View 1 Replies
View Related
Sep 15, 2011
I was hoping that the latest firmware would fix my (2) 'bugs', but it did not. We are using the RV042s at our remote medical clinics as an end-point VPN router to our Nortel 1700 VPN router, replacing our old Nortel Contivity 100s.When I try and do a reset when connected remotely via the WAN interface, the RV042 hangs and will only reset by re-powering.
View 1 Replies
View Related
Feb 18, 2013
I have an RV042 VPN tunnel with an RV082.The RV042 has a public IP Address obtained by PPPoE, the RV082 has a public IP Address obtained via Static IP.The problem I see is a really slow performance. Both internet conections are idle and the performance is about 2 or 3 kbyte/s My question are if I should I enable any of this:
- Agresive mode
- NAT Traversal
- IP Compresion
- Dead Pear Detection
How can I troubleshot this slow performance?
View 2 Replies
View Related
Feb 6, 2012
i have setup vpn connection (client-gateway) using quick vpn ( default cisco) and third party like thegreenbow. connection is ok (established) but why from outside I can only ping to IP LAN PC , if I ping ip server the result is request time out(failed). I have been trying do this to 3 server ( windows server 2003 as OS).four your information I have made firewall "OFF" on all of those servers. the result is same, failed.
View 0 Replies
View Related
Jul 18, 2011
Im able to create a gateway tunnel with two rv042 routers in different locations ( i can see the tunnel connected in the router) but the quick vpn utility is not working , i also tried to use the pptp as server as an alternative( im able to connect using windows connection to the pptp server but whenever I browse any of the four ip's allowed for the pptp server \10.0.0.200-204 it takes me to the documents of the local computer....I attached the configuration for one of the routers it is the same as the other end , just the information is flipped.
Message was edited by: Adrian Torres
View 7 Replies
View Related
Dec 2, 2012
We connected to locations to the RV042 by setting up 2 Gateway - to - Gateway VPNs - both locations can communicate with the RV042 and devices within the local LAN of the RV042 - however at the moment it is not possible to send traffic from 1st VPN Location to the 2nd VPN location
View 1 Replies
View Related
Apr 18, 2012
i am using RV042 router, i have configured DMZ in this, DMZ is not passing the traffic, i am able to ping the DMZ ip from the server. but the server is not getting the Internet.
View 1 Replies
View Related
Aug 7, 2011
Is it possible to use protocol binding to route pings only over the WAN1 connection, even if WAN1 fails? It seems like the protocol binding feature of the Linksys RV042 is ignored once WAN1 fails. I would like to use a ping from the LAN to an external IP to verify if the WAN1 connection is down, or is up and then use that information to power up, or power down a secondary communications system (WAN2). However, if the protocol binding is ignored when WAN1 fails, then I will not be able to use the ping to establish the state of WAN1 connection. Addtionally, is it possible to use protocol binding to only route pings and allow all other traffic to use either WAN connection? I have seen these feautures on a different brand of router that failsover to a cell connection, but it is not a true dual WAN router. It would be nice if the RV042 would allow this kind of control. Are there any other dual WAN routers out there that have this kind of protocol binding feature?
View 1 Replies
View Related
Oct 25, 2011
I defined a static route: 192.168.0.0 / 255.255.255.0 / 192.168.1.201 (gateway), I can connect from 192.168.1.0 to 192.168.0.0 but we cannot ping in this local network. We have a CISCO 18000 as a VPN IP configured between this two local network.
View 1 Replies
View Related
Nov 27, 2012
I would like to allow PING on RV042 from WAN side only from specific IP address, but when I set the rule, RV042 does not respond on WAN side, because Block WAN Request is Enabled.BUT! When I disable "Block WAN Requests", now any IP can ping my router from WAN side. Although I set access rule to Deny Ping from WAN side to anyone, it still responds.
View 1 Replies
View Related
Feb 12, 2012
We have a managed service provider voip network that requires us to use our own router for the data network. We wanted to use the RV042 for it's easy vpn setup. After installing it worked great for about 10 min. then the WAN port stopped passing traffic. 3 min. later it started working again. We tested the RV042 on a different network and it works fine. We tested an older Pix on the managed network and that works fine. But the RV042 will not work on the managed service provider voip network. The service provider says that on their end it shows our WAN port going up and down.
View 1 Replies
View Related
Sep 3, 2012
I'm having some problems blocking IP blocks. I have several blocks of IP's that I want blocked.I want to block 77.0.0.0/8 from communicating with a server on my lan.So I make a rule in the RV042 to deny all traffic from 77.0.0.0 to 77.255.255.255, source wan1, destination lan, my server's ip,As soon as I move that rule above the traffic forwarding rules I have created, no traffic moves in or out via the wan interface. It seems to just cut off all traffic.
View 2 Replies
View Related
Sep 9, 2011
Replaced an older RV042 that had damage from lightning. The new RV042 is V03 with firmware 4.0.0.7. This router supports 7 branch offices using site-to-site VPN to other RV042 routers. After connecting the new RV042 at the main office, three of the branch offices had very slow response over the VPN tunnel. I disabled the firewall on the new RV042 and the problem resolved. The three branches with the problem have Windows 7 systems and the other 4 have Windows XP. I confirmed that the Windows firewall was disabled on the Windows 7 systems.I did try leaving the firewall enabled and disabling SPI, but that didn't work. Have to have firewall disabled to resolve the problem. I would not expect the firewall on the main office RV042 to affect VPN tunnel traffic, but apparently it does. Do we need specific access rules to fix the issue. It works fine with firewall disbaled, but I'd be more comfortable with it enabled.
View 2 Replies
View Related
Jul 31, 2012
I have an RV042 router and I'm looking to monitor the total upstream and downstream traffic from within the router.
I know there is tons of software that I can put on a network computer to monitor traffic, but is there any software that I can put on the router itself that will monitor the traffic from within the router?
View 2 Replies
View Related
Jan 27, 2012
I am setting up remote access using an RV042 router. Using quickvpn or a client-to gateway vpn and shrewsoft client, I can only access/ping the LAN side of the remote router and one machine on the remote network. The PPTP server and native Windows 7 connection provide access to all machines on the remote network.I have 2 possible reasons for this and would like to find the real reason:
1) The remote RV042 is behind another router, and that router restricts access other than the PPTP traffic.
2) The VPN tunnels other than PPTP only allow access to the remote LAN side of the router and remote machines that have the remote router defined as their gateway in the IP configuration.
View 2 Replies
View Related
Mar 28, 2013
On the System Summary screen in the Port Statistics table when you click on one of the Connected links the pop open window does not show the IP address of the connected device when using IPv4. Where can I find this?
If the devices are using static IP addresses and not getting them from the DHCP server they do not show in the Client Table under DHCP Status.
If they are know MAC addreses because they have been assigned to static IPs on the DHCP setup screen they will not show up in the Uknown MAC Addresses pop up window.
View 1 Replies
View Related
Feb 13, 2012
I'm trying to setup a VPN between an RV042 V3 and an RV082 V2 router. They get connected but no traffic gets through the tunnel. I tried with and without firewall,DPD, Keepalive, forward secrecy but nothing worked. What should I do? I don't want to throw out the V2 routers. V3 to V3 connects fine.
View 1 Replies
View Related
Feb 24, 2013
We have offices in USA and Venezuela.In our USA office we have a RV042 router and in Venezuela we have a RV082 router.We have connected a VPN tunnel (gateway-to-gateway) between both offices.
The point is:How could we redirect the internet traffic from our Venezuela office (RV082) to the USA Office (RV042) to navigate using USA public IP's?
The reason for this is that we need to use online streaming services which are only available for IP's from USA and we can't use them from the Venezuelan IP's.
We can not use the PPTP option since the equipment which will use the streaming services (like hulu, crackle, etc.) in Venezuela is a Google TV device which doesn't allow the configuration of proxy navegation or PPTP VPN connections itself. That's the reason why we need to do that through the routers.
View 1 Replies
View Related
Dec 19, 2011
We have a VOIP system from AT&T with T1 internet access. I have a RV042 setup as the default gateway for the network and the router randomly (usually over the weekend loses the internet). I have updated to the latest firmware and have check all logs on the server. When the internet access goes down we can still access the internal network. I have been power-cycling the router and then everything works fine. Is there a known issue with this router radomly blocking internet access in or out? This device should remain working at all times so that our remote users can access the company network.
View 0 Replies
View Related
Aug 1, 2012
I have an RV042. I understand and have created the services I need. The documentation is just not clear on how to direct traffic for these services to a specific wan port.
Can this even be done with this router? If so, the how? Use rate control or priority? Does checking a wan port mean that it will only go through that port?
View 4 Replies
View Related
Jan 2, 2013
I have a RV042 (firmware 1.3.13.02-tm). Is it possible to configure so traffic from a specific domain (incl. its sub-domains) is directed exclusively to one WAN port?
View 10 Replies
View Related
