Cisco Routers :: RV042 No Traffic Moves In Or Out Via WAN Interface
Sep 3, 2012
I'm having some problems blocking IP blocks. I have several blocks of IP's that I want blocked.I want to block 77.0.0.0/8 from communicating with a server on my lan.So I make a rule in the RV042 to deny all traffic from 77.0.0.0 to 77.255.255.255, source wan1, destination lan, my server's ip,As soon as I move that rule above the traffic forwarding rules I have created, no traffic moves in or out via the wan interface. It seems to just cut off all traffic.
We connected to locations to the RV042 by setting up 2 Gateway - to - Gateway VPNs - both locations can communicate with the RV042 and devices within the local LAN of the RV042 - however at the moment it is not possible to send traffic from 1st VPN Location to the 2nd VPN location
i am using RV042 router, i have configured DMZ in this, DMZ is not passing the traffic, i am able to ping the DMZ ip from the server. but the server is not getting the Internet.
We have a managed service provider voip network that requires us to use our own router for the data network. We wanted to use the RV042 for it's easy vpn setup. After installing it worked great for about 10 min. then the WAN port stopped passing traffic. 3 min. later it started working again. We tested the RV042 on a different network and it works fine. We tested an older Pix on the managed network and that works fine. But the RV042 will not work on the managed service provider voip network. The service provider says that on their end it shows our WAN port going up and down.
Replaced an older RV042 that had damage from lightning. The new RV042 is V03 with firmware 4.0.0.7. This router supports 7 branch offices using site-to-site VPN to other RV042 routers. After connecting the new RV042 at the main office, three of the branch offices had very slow response over the VPN tunnel. I disabled the firewall on the new RV042 and the problem resolved. The three branches with the problem have Windows 7 systems and the other 4 have Windows XP. I confirmed that the Windows firewall was disabled on the Windows 7 systems.I did try leaving the firewall enabled and disabling SPI, but that didn't work. Have to have firewall disabled to resolve the problem. I would not expect the firewall on the main office RV042 to affect VPN tunnel traffic, but apparently it does. Do we need specific access rules to fix the issue. It works fine with firewall disbaled, but I'd be more comfortable with it enabled.
I have an RV042 router and I'm looking to monitor the total upstream and downstream traffic from within the router.
I know there is tons of software that I can put on a network computer to monitor traffic, but is there any software that I can put on the router itself that will monitor the traffic from within the router?
We have offices in USA and Venezuela.In our USA office we have a RV042 router and in Venezuela we have a RV082 router.We have connected a VPN tunnel (gateway-to-gateway) between both offices.
The point is:How could we redirect the internet traffic from our Venezuela office (RV082) to the USA Office (RV042) to navigate using USA public IP's?
The reason for this is that we need to use online streaming services which are only available for IP's from USA and we can't use them from the Venezuelan IP's.
We can not use the PPTP option since the equipment which will use the streaming services (like hulu, crackle, etc.) in Venezuela is a Google TV device which doesn't allow the configuration of proxy navegation or PPTP VPN connections itself. That's the reason why we need to do that through the routers.
We have a VOIP system from AT&T with T1 internet access. I have a RV042 setup as the default gateway for the network and the router randomly (usually over the weekend loses the internet). I have updated to the latest firmware and have check all logs on the server. When the internet access goes down we can still access the internal network. I have been power-cycling the router and then everything works fine. Is there a known issue with this router radomly blocking internet access in or out? This device should remain working at all times so that our remote users can access the company network.
I have an RV042. I understand and have created the services I need. The documentation is just not clear on how to direct traffic for these services to a specific wan port.
Can this even be done with this router? If so, the how? Use rate control or priority? Does checking a wan port mean that it will only go through that port?
I have a RV042 (firmware 1.3.13.02-tm). Is it possible to configure so traffic from a specific domain (incl. its sub-domains) is directed exclusively to one WAN port?
I wonder if I can have a RV042 VPN Tunnel to a RV082, and in the RV082 block all traffic to the internet that comes form the PCs that are behind the RV042.
Remote PC -> RV042 -> VPN -> RV082 -> RV082 Firewall (block internet traffice, allow intranet traffic)
We bought an RV042 at the end of June. It is used as a gateway and VPN router. DHCP server is disabled and all IPs are configured manually.Every once in a while (Tuesday night, then Friday night - yesterday, it has hapened once or twice before that) the router appears to restart (see log below) then comes back up with system time of Jan 01 2010. At this point the router will no longer load its configuration page (https://10.29.238.197:16443/) and VPN connection to our customer in Africa drops. However, devices behind the router can be reached and can access the internet. The only way to fix this is to power cycle the router at which point everything starts working flawlessly again.The PID VID is RV042 V03 running firmware v4.0.3.03-tm (May 12 2011 21:27:37). Our RV042 is a newer one with Cisco SMB Router branding not the older Linksys branding.
From the log when the router reboots:
Aug 12 22:38:42 2011VPN Log(g2gips0) #141: retransmitting in response to duplicate packet; already STATE_QUICK_I2Jan 1 01:00:05 2010System Logheart : System is upJan 1 01:00:13 2010System LogWAN connection is up : 10.29.238.197/255.255.255.192 gw 10.29.238.225 on eth1Jan 1 01:00:15 2010VPN Log(g2gips0) #1: [Tunnel Negotiation Info] >>> Initiator Send Main Mode 1st packet
I looked at the log more and all the usual messages assosciated with VPN being established are there - the last thing in the log before the router coming back up again is:
Jan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: sent QI2, IPsec SA established {ESP=>0x575a01c0 <0x6534ae4e
So it even claims the tunnel should be up but I can never reach anything on the far side.
I am trying to set up my router to grant http traffic a minimum bandwidth of - for example - 5,000 kBit (if there is any http traffic).
So I set http min. rate to 5,000 while I set nntp min. rate to 1 However, when I run nntp downloads on several connections (e.g. 10) my single http download never goes above 1,000 kBit. Without any other connections I reach 8,000 kBit.
Initially we had a rv110w in place and had problems with the port forwarding stopping a few times a day so we replaced with with a RV180W. Now port forwarding appears to be staying up, however I have a new problem. We host a web page, for some reason when an internal user points the url to the web page it resolves to the web interface of the Router and not the expected web page. If you are outside of the network it resolves to the correct web page. I am not sure why this is happening as it didn't happen with the RV110W or the PIX before that.
My question is can my traffic goes from inside interface to outside interface? (because the inside interface address not from 10.0/172./192.168 private address)Also I'm allowing internet from this email server (132.147.162.14) so what my access list to be configured? and what my subnet mask shoud be there?
Pix(config)#access-list outbound permit tcp 132.147.162.14 255.255.0.0 any eq 80 Pix(config)#access-list outbound permit udp 132.147.162.14 255.255.0.0 any eq 53 Pix(config)#access-group outbound in interface inside
I have a two RV042 VPN Router, I successfully connected the IPSEC tunnel. I cannot route Traffic in the tunnel. See the diagram.
MAIN Network 10.252.x.x --------------> FIREWALL a.a.a.1 INTERNET RV042a WANa <<------------------------------->> WANb RV042b a.a.a.2 b.b.b.b
In this manner the network of b.b.b.b wil connect to the Main Network 10.252.x.x, unfortunately I can't pass traffic to RV042b going to RV042a. Everytime I trace the route, the traffic goes outside the Internet not to RV042a.
I just acquire the RV042.We have a DSL [WAN1 :download good, bad uplaod] and an SDSL line 4MB OVH [WAN2].
Receive all downstream traffic to WAN1Send email upstream traffic to WAN1Send upstream traffic to OVH and guarantee good bandwidth to 10 TSE access and webex traffic I built the following rules:
The problem ... nothing works ... the downstream traffic comes from WAN2 and upload on WAN1 or WAN2.
I have two Windows Boxes connected to RV042 ; each has its own static IP assigned to it and each runs bunch of virtual machines , for which I had configured port forwarding .My hosting company claims that my server(s) are listening on IP 192.168.0.1 on a public interface (i.e., one that uplinks to their network). They see this same IP on two different MACs my uplink interface. I am not really sure how it is possible since 192.168.0.1 was assigned to router itself.
link where to download user manual and/or Technical manual for Linksys RV042 Dual WAN VPN RouterDoes the Linksys RV042 Dual WAN VPN Router AGGREGATE the bandwidth of the two WAN Ports for LAN use or how does it operate?Does it manage traffic on Layer 7 (Application Layer);can i configure say, yahoo messenger traffic to take priority over youtube traffic or http traffic over download/upload traffic or such?Does it have DYNAMIC bandwidth allocation/management feature?Can i Guaranteed Bandwidth Allocation for a particular user or IP Address?Does it have TCP Ack Prioritization feature?Can i direct site(s) traffic,say cisco.com and/or port or service to use a particular WAN port?If this product cannot handle this features?
In our USA office we have a RV042 router and in Venezuela we have a RV082 router. We have connected a VPN tunnel (gateway-to-gateway) between both offices.
The point is: How could we redirect the internet traffic from our Venezuela office (RV082) to the USA Office (RV042) to navigate using USA public IP's?
The reason for this is that we need to use online streaming services which are only available for IP's from USA and we can't use them from the Venezuelan IP's.
We can not use the PPTP option since the equipment which will use the streaming services (like hulu, crackle, etc.) in Venezuela is a Google TV device which doesn't allow the configuration of proxy navegation or PPTP VPN connections itself. That's the reason why we need to do that through the routers.
I have an RV042 router and I'm looking to monitor the total upstream and downstream traffic from within the router. I know there is tons of software that I can put on a netowrk computer to monitor traffic, but is there any software that I can put on the router itself that will monitor the traffic from within the router?
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
We have a RV042. remote management is set to DISABLE - but even after restarting the router i can access the interface remotely over the internet.even when i enable it and change the port to say 5555 i can connect to the web interface using either port 5555 but ALSO on port 80.what's wrong here?the only way to stop that was to create a rule that blocks port 80 on the WAN interface. (btw. could this rule affect LAN users when browsing the web?)
There is a remote server that downloads info from a server here at HQ. When the dowloads start the rxload on the S0/0/0 interface jumps to 98 percent or so; rxload 250/255. I needed to limit the bandwidth utilization between the servers, so I added the below line to the LAN interface on the remote router.By adding the command, it reduced the download utilization -which is what I wanted.
access-list 185 permit ip host 10.6.27.1 any ! int f0/0 traffic-shape group 185 10000 8000 8000 1000
Question:How would applying this to the LAN interface cause the download utilization (Coming from s0/0/0) to decrease?
i want to monitor interface traffic in/out by eem and the if the values is overer than some value i will change the policy. for example my router is 2821 is have 2 fastEthernet port , i want to monitor the traffic on fasE1/0 if traffic over than 80Mbps i will change some configuration ( example: change next-hop on static route) for via traffic to interface fasE1/1 for reduce the traffic on interface fasE1/0?
I want to allow ICMP traffic on ASA 5510 from LAN interface to DMZ. I've permit any traffic and added ICMP to the inspestion list also but still there is problem. Belos is the configuration. The image is asa822-k8.bin
I am facing a very big problem with site to site vpn on cisco 2900 ios.
I configured the vpn and when i ping from router itself to destination ip with source as lan interface , VPN works, no problem.
but when i connect any computer directly to router's lan interface to initiate traffic , it doesnot work at all. and on computer's lan i see yeloow sign.
mtu is 1500, speed is auto (I tried changing also) , duplex is auto ( i tried changing also) , through firewall on pc should not affect but still i disabled it.
since their is no problem with vpn config as vpn comes up when i initiate ping from router itself but i dont know why it is not working from lan.
do we need any inspect icmp on this router also ? or any policy modification to pass traffic across the interfac on router is required ?
I was useinf c2900k9-15.0(M4).bin and i upgraded it to 15.3 which is lated to get reed of any bug .
I connected two laptops directly to router's gi0/0, g0/1 interface to ping from one laptop to another but this also did not work.
I have two ethernet adaptors on my windows machine. OS is Win-XP.I am running ADSL broadband on LAN1 and on LAN2 I am accessing applications on our company's WAN. LAN1 is on 192.168.1.0/24 subnet and LAN2 is on 10.68.104.0/22 subnet.Accessing application through LAN2 involves DNS that is located distantly, therefore routers are also in picture.Problem is that while accessing the application that run on the network of LAN2, I have to disable LAN1. Otherwise the traffic goes on LAN1.
I have an ASA-5505. [code] I have an Exchange server on the 10.10.10.0 network. I need to be able to allow Active-Sync and OWA from the Guest WiFi through to the Exchange server on the 10.10.10.0 network. The Guest Wi-Fi uses external DNS so traffic is going out to the Internet and getting an IP address which is of course assigned to the Outside interface abd trying to come back in on that interface.How do I make this do what I need? How do I setup the rules to allow this traffic?
FTP traffic routed from outside to the inside interface works fine. I have another interface with multiple sub-interfaces and vlans configured. FTP traffic routed from the outside to vlan2_servers is not making it through the firewall. I must be missing something. I have attached my config.
I have my main branch router (3825) and two remote routers (2821's). They are connected through leased lines that do not touch the internet. For various security reasons I have to ensure that the traffic from the remote's are encrypted in a VPN tunnel even though it is still part of a private network.I have went ahead and created the tunnels and I can verify that they are up. I have applied the cryptomap to the correct interfaces, etc.So the question is - How do I ensure that traffic is not just being router out of the interface from the remote sites back to the branch router with or without using the VPN tunnel? I've taken down the tunnels and of course, the traffic is still being passed back and fourth.
