I have an RV042 router and I'm looking to monitor the total upstream and downstream traffic from within the router. I know there is tons of software that I can put on a netowrk computer to monitor traffic, but is there any software that I can put on the router itself that will monitor the traffic from within the router?
View 1 RepliesI'm using an RFC 1483 Bridged adsl connection on a WAG54GS router. Downstream rate says 2043 Kbps, and upstream rate only 35 Kbps. In the router setup page I have not found any place to change downstream/upstream rates. How can I increase \the upstream rate?
View 2 Replies View Relatedlink where to download user manual and/or Technical manual for Linksys RV042 Dual WAN VPN RouterDoes the Linksys RV042 Dual WAN VPN Router AGGREGATE the bandwidth of the two WAN Ports for LAN use or how does it operate?Does it manage traffic on Layer 7 (Application Layer);can i configure say, yahoo messenger traffic to take priority over youtube traffic or http traffic over download/upload traffic or such?Does it have DYNAMIC bandwidth allocation/management feature?Can i Guaranteed Bandwidth Allocation for a particular user or IP Address?Does it have TCP Ack Prioritization feature?Can i direct site(s) traffic,say cisco.com and/or port or service to use a particular WAN port?If this product cannot handle this features?
View 1 Replies View RelatedIn our USA office we have a RV042 router and in Venezuela we have a RV082 router. We have connected a VPN tunnel (gateway-to-gateway) between both offices.
The point is: How could we redirect the internet traffic from our Venezuela office (RV082) to the USA Office (RV042) to navigate using USA public IP's?
The reason for this is that we need to use online streaming services which are only available for IP's from USA and we can't use them from the Venezuelan IP's.
We can not use the PPTP option since the equipment which will use the streaming services (like hulu, crackle, etc.) in Venezuela is a Google TV device which doesn't allow the configuration of proxy navegation or PPTP VPN connections itself. That's the reason why we need to do that through the routers.
using task manager in XP it is clear that while browsing data is being uploaded mirroring the data downloaded..ie in a given period if 18mB comes downstream (just surfing) then 11mB goes upstream. The graph in task manager shows that the peaks and troughs of the data upstream and downstream exactly correspond and watching the bytes tick over confirms that data goes out for every data coming in.I assume that this should not happen? I realise ip protocols have some kind of error detection that may require uploading data, but the amount sent seems excessive! From my limited understanding of networking and running wireshark it looks like that when packets come from an ip on the web ( i use the terms web/internet interchangeably ) then packets are sent out to the same ip ... using TCP and HTTP ( I don't really understand them ). The info for one such packet going out is "Continuation or non-HTTP traffic" using the HTTP protocol, which sounds a bit contradictory. I regularly run virus scans and rarely find anything. The cpu regularly maxes out and its usually something to do with firefox ( I've heard of buffer overflows but i assume the problem is a relatively old processor and hardware).The browser is firefox. OS is XP.Coincidentally, the pc was recently rebooting after crashing until I disabled "restart on system failure" which prevented the crashes ( if they were crashes and not just the system reacting to an error ). Again, that is a bit suspicious but maybe not. Spybot, bit defender quickscan,avira, zone alarm, malwarebytes etc haven't flagged anything up.Maybe the router is not configured properly. As with all these things, there will be some simpler things to start with to diagnose this issue (if there is one ) but I don't know what they are.The pc uses wifi to connect. The isp is not the best and the speed is pretty bad for adsl. Every couple of days the router needs rebooting because it stops giving out ip's.
View 6 Replies View RelatedYesterday, I changed my old belkin n1 router with Linksys WRT54GL router. Ever since them my upstream speed is really slow. I did the speedtest its like .5mbit. My downstream speed is just fine. This issue is only on wired computers, upstream speed on wireless computers is just fine.I retested router & modem several times, my upstream speed is normal when I connect cable directly from modem to my computer.Current Firmware Version is 4.30.14 build 5.
View 1 Replies View RelatedI have an RV042 router and I'm looking to monitor the total upstream and downstream traffic from within the router.
I know there is tons of software that I can put on a network computer to monitor traffic, but is there any software that I can put on the router itself that will monitor the traffic from within the router?
I am trying to come up with the best way to traffic shape traffic with 3750 Me switches. the traffic will be coming from a 6504 Sup-7203b downstream and going out the wan. Core---L3---->6504--intvlan80--trunkport to--->3750Me---g/1/1/1-trunkport to---MetroE network--->int f0/0.80--branch router. The idea is to use the 3750 to traffic shape the traffic going towards the wan/branch to 500 to match the contracted rate and then to use qos on shaped rate. I tried to apply it to g1/1/1 using port based policies but it did not shape the traffic. I changed everything to IP interfaces and it worked. I need to break up the metroe into different vlans so I can bring branch offices in on different vlans.c
View 3 Replies View Related2 routers in series, is one more secure. I recently asked about setting up two routers in series as routers, one wireless one not. It was my understanding that the computers on the second router would not be visible to computers on the first router, the wireless one. My assumption was that this would make it more difficult for someone who got access to the wireless router to also access those computers on the second router.
View 3 Replies View RelatedI just got optical fiber installed in my place which gives me great download speeds. Now my ISP has a monthly download limit of 120GB, after that I gotta pay overages.Now my setup is like this: Fiber modem (1 port) -> Linksys E3000 router (4 ports + wifi).All my gear is hooked up to the Linksys router (xbox, ps3, media center, office pc & 2 laptops).I would like to keep track of the total "internet" bandwidth use of all devices, but exclude the normal network traffic, as that of course I don't pay for.Is there something that I can install on the Linksys router that can keep track of that kinda of information? router (4 ports + wifi).
View 6 Replies View RelatedI have a WRT160N router. Are there any network software packages out "there" than will allow me to track the total traffic on this device?
View 1 Replies View RelatedSince I've bought my RV042 CISCO (v3 hardware, firmware v4.1.1.01-sp Dec 6 2011 20:03:18) i wasn't able to let it work properly with my two DSL network lines. I explain. I got 2 DSL network:
1- PPPoE with authentication (MTU setted as auto) with upstream speed 4Mbit/S and downstream speed 5Mbit/s
2- Direct line with static IP with upstream speed 7Mbit/S and downstream speed 1Mbit/s
I was never able to SUM the two WAN using the LOAD BALANCE set. I tried all combinations:
DSL 1 in WAN 1 or in WAN 2
DSL 2 in WAN 2 or in WAN 1
I've tested all type of speeds in WAN SPEED in Web Management
it seems that for some kind of reason it takes the upstream speed i can set in web management as the default value on which it decides to use the other WAN. When i set low upstream bandwidth for DSL 2 it's able to sum the down streams of both WANs but not the up streams.
I wasn't ever able to sum the up streams? How does it work?
I would like to the the RV042 for a one to one NAT, but I need it to NAT to an address that is not on it's local subnet. I have it routing properly to the address, but web interface only allows adding an IP on the local subnet. Is there a way around that?
View 1 Replies View RelatedWe have 3 Cisco RV042. These were purchased to permit VPN from two branch offices to our head office. VPN is required to permit the two branch offices to use Avaya IP phones to connect to our main head office switchboard.We also have users on Blackberry and Apple iPhones to collect their mail through OWA from our Exchange 2010 server.
I've noticed in one of your threads that the RV042 routers configured for VPN do not permit the use of HTTPS to connect to OWA and that seems to be the problem for us. Since installing the VPN our OWA access is not possible.
What can I do to resolve this problem and what router would you suggest that I could use at the head office to enable the two branches to connect VPN to head office? And if there is a suitable router, would I need to replace all three?
I have never setup a GW to GW VPN with a FIOS connection. I have done it with DSL and cable without any problems.
View 1 Replies View RelatedI'm experiencing quite a slow vpn performance. I've tested different scenarios.* Windows XP with built-ín pptp client and Shrew ipsec client* Linux built-in pptp* wireless and wired connections? I never managed to go above 1MBps neither with windows or linux. I managed to go up to 3MBps using the Shrew client.I've also checked mtu settings and everything seems to be fine.
View 1 Replies View RelatedI am converting from a Cisco Model 850 to a RV042, all is well so far but I cannot implement one feature I had on the old router.I want to do one to one nat from one internal ip to one external ip but I only want to use one tcp/ip port.The command to do this on the old cisco 850 was this:"ip nat inside source static tcp 192.168.1.181 80 75.xxx.xxx.181 80 extendable"Can this be done with the RV042?I can do one to one nat but it include all ports.
View 1 Replies View Relatedmy office network is running using a Linksys Router RV042 and at home i have a Linksys Router BEFVP41. i'm trying to setup a QuickVPN from home to my office but having problems. both routers have different LAN IPs. the firmware version for my two routers are listed belowRV042 - ver. 1.3.7.4BEFVP41 - ver. 1.02.00?
View 5 Replies View RelatedLAN L1, with IP addresses 192.168.10.x, for Company C1
LAN L2, with IP addresses 192.168.11.x, for Company C2
I have networks separated: different racks (but very closer fisically: a wire can be thrown), different gateways (to DSL), but both LAN's must connect with each other. I have acquired two RV042, one for each company to create VPN's (permitting telejob).
I tried to upgrade the firmware of my RV042 router. I downloaded the file (RV0XX-v4.0.0.07-tm-20100819-code.bin) and check the cheksum. When I try to upload it, I have the message "413 Request Entity Too Large". How can I do ? Should I unzip the .bin file (it's about 30Mo) ?
View 1 Replies View Relatedi am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
[code]....
My quickvpn setup has been working great for a few years but it stop working recently with the following error message in wget_request_error.txt: HTTP request sent, awaiting response... 501 Not Implemented 20:10:10 ERROR 501: Not Implemented.quickvpn hangs on the dreaded verifying network stage.Checked VPN router logs and also quickVPN client logs and confirmed the tunnel has been created successfully. However the ping was unsuccessful.I look through the forum and confirmed that my quickvpn user account and password only contains alphanumeric characters.
View 1 Replies View Relatedstatic route on RV042?
View 1 Replies View RelatedWe have a Network set up with a RV042 router. Router is hooked up to Cox Cable and ATT DSL. Currently have 20 computers hooked up to the router all using Static IP addresses. Setup has been in place for over 7 years. I want to set up a Wireless Access point on this network. The problem is, I can't seem to get DHCP to work right even WITHOUT the Wireless Access Point. I have taken one of the computers that works great with a static IP and changed it to be DHCP, I have enabled DHCP on the router and set the from and thru parameters for the IP assignment. The computer will connect and get an IP address and it allows me to see all the INTERNAL servers on the network but going to the Internet is REAL FLAKY. I usually have to refresh 5 or 6 times to get a web page and sometimes even that don't work. If I do get a page to come up there is about a 10% chance that it will bring up a subpage of that page without doing a refresh 5 or 6 times. Its like it won't hold the connection to the Internet. I did notice one thing different in the User Manual of the RV042 that is different than all the other Linksys routers I have worked with. It says that when you enable the DHCP on the router, you then make sure ALL computers hooked to it are set for DHCP. All other routers I have worked with do NOT use that word ALL. Am I missing some setting or is this a binding thing where you are either ALL static or ALL DHCP?
View 1 Replies View RelatedSmall office, 2 RV042, 2 DSL connections. 1 is used striclty for the business side, and the other is for our CCTV network. They also have seperate DSL connections as we have 2 external IP address for clients to connect remotely. We don't want to take away our exisring setup, but would like to bridge both networks so a few of our internal clients can connect to our CCTV network and use some of the devices. Right now they come in on VPN but its not as fast.Is this doable without adding additional hardware? Both networks need DHCP enable as well.
View 1 Replies View RelatedI have been running a email/web/ftp server on one server for 9 years. I have currently acquired a Barracuda spam 300. I cant get the emails to go thru the barracuda first. Here is how it is setup: my email and web come in thru one outside address..call it 166.5.5.5 I have a 1 to 1 nat for 166.5.5.5 to 10.0.0.2 (email/web/ftp server) ports 25 and 53 are forwarded to the 10.0.0.4 (barracuda) then out on 25 to my 10.0.0.2 no emails go thru as long as it is set this way I can nat the 166.5.5.5 to the barracuda first and emails go thru, but I lose my web and ftp will this router work for me? I was told that i needed to change mx records for email to 166.5.5.6 and then forward nat on that address to the barracuda. I dont really want to change mx records for 10-12 email domains.
View 1 Replies View RelatedI am currently using Netgear FVS338 Routers / VPN Devices in 3 different locations and honestly I am not happy / impressed with them whatsoever.I have been doing some research and came across the Linksys RV042 and RV082 devices that caught my eye. The question is what is the VPN throughput of these devices?I have gone over the website, spec sheets and they only really say the throughput of the LAN Links and not the WAN Links. I currently have very reliable 20Mb+ Synchronous connections between all 3 sites and have not been able to get any good performance out of the Netgear devices and contacting their support is a joke. They can't tell you anything other than it should work or we will swap out the unit. Well if I have 3 of them that have been purchased at all different times I don't believe that they are all having the same issues. What these units 3DES VPN Throughput and will more than likely be purchasing 3 of which ever once suits our needs immediately.
View 9 Replies View RelatedDid anybody ever succeeded upgrading 1.3.12.19-tm to 4.0.0.07-tm version?
View 1 Replies View RelatedI have a RV042 router and we are trying to set-up our OWA for outside access. I can't figure out which ports or which page those ports are on to open them. We are a small company and we do not have IT except for ourselves. The internal network works fine but i can't get the Exchange access from outside.
View 2 Replies View RelatedHaving a problem everytime I try to use load balance on my Rv042 it is slow as a dog and sometimes wont connect at all. if I run in smart backup mode its fine. removed firewall rebooted everything tried numerous configerations upgraded to the latest frimware just about to be convinced
View 2 Replies View RelatedI've got an RV042 router at home and am connected from my office via the QuickVPN client ver 1.4.1.1.2. I can ping the RV042 and log into the administration page and make changes. However, I can not see other computers on the remote network. I can not ping them. When I open my Network page, I still see the computers on my local network.
All machines are running Windows 7 Ultimate. ISP is Comcast at both locations. WAN IP's are dynamic, but have not changed in over a year. Local IP's on the remote (home) network are static..[url]....
Spent a lot of time trying to configure a time warner set up. Users are using 2 SMC 8014 and one RVO42 on the network. Cannot access the internet.
View 1 Replies View RelatedWe have an RV042 router.I'm looking for a solution where my drop-in clients would have their own WIFI key to access Internet, with no access to our LAN.
-Can I place a Wifi AccessPoint on the DMZ so my drop-in clients use it to connect to the WEB.
-While putting another Wifi AccessPoint on a regular LAN port for Employees to use and stay within the LAN?