Linksys Wireless Router :: WRT54GL Slow Wired Upstream Speed
Aug 20, 2011
Yesterday, I changed my old belkin n1 router with Linksys WRT54GL router. Ever since them my upstream speed is really slow. I did the speedtest its like .5mbit. My downstream speed is just fine. This issue is only on wired computers, upstream speed on wireless computers is just fine.I retested router & modem several times, my upstream speed is normal when I connect cable directly from modem to my computer.Current Firmware Version is 4.30.14 build 5.
View 1 Replies
ADVERTISEMENT
Dec 6, 2012
I'm having an issue with my new E1200 routeur : I have a 100mbit/s connection and since i installed the E1200 , the speed is cut in half : Max 50 mbit/s .. ( or if this is an hardware limitation ? )
I have a gigabit network card with my pc , everything is fine on the pc / network side as i had these speed fine ( 100mbit/s ) with my old ISP router , ( wich i switched in bridge mode to use the E1200)
View 3 Replies
View Related
Apr 3, 2012
I have a problem with my download speed. I'm supposed to have a speed of 60 MBPS and when I collect my computer direct to the modem I received it but with my e2000 router, the 3 computer connected to it can't reach more than 30 MBPS. I just updated the firmware of the router to the newest version but nothing changed.
View 2 Replies
View Related
Jun 22, 2011
My newly installed E1200 only sends speeds of about 16 mbps wireless, but sends the ful 60 mpbs when wired. What is going on. Firmware is up to date. Changing the channels didn't do anything. Is there a way to figure out if the problem is with my laptops wireless card.
View 9 Replies
View Related
Feb 8, 2011
I am using a Cisco RVS 4000 to test a new 10M/10M internet connection. I'm having a small problem performing the ISP's speed test (speedtest.cavtel.net). The download test consistently gives me 10Mbit/s, full speed for the connection, however the upload speed is usually about 5.5 Mbit/s. My ISP has been onsite and has checked the lines and tested directly, and we have determined that if connected directly we can test to full upload speeds, but when the RVS is connected, we cannot get full speed.
We've tried different cables, reseting to factory defaults, updating firmware, changing port settings, and toggling most of the other setting on the router. Some settings do have a minor effect on the upload speed, but nothing that gets me back up to 10Mbit/s.
I did notice that there appears to be no way to set speed and negotiation settings on the WAN port. Perhaps I am missing it, because that seems like a possible culprit.
Otherwise, the only only thing I can think of is a warranty return to determine if the unit itself is defective.
View 1 Replies
View Related
Aug 1, 2012
I have an RV042 router and I'm looking to monitor the total upstream and downstream traffic from within the router. I know there is tons of software that I can put on a netowrk computer to monitor traffic, but is there any software that I can put on the router itself that will monitor the traffic from within the router?
View 1 Replies
View Related
Jul 11, 2011
I want to add more than 40 mac address filter into my WRT54GL with firm version V4.30.7 but the form to enter the mac address list just limited to 40 mac address register. How do I can add more than 40 mac address list in my WRT54GL ? perhaps we can add the list into WRT54GL like XML file or somehow that can make me add more than 40 mac address register list.
View 2 Replies
View Related
Dec 22, 2011
2 routers in series, is one more secure. I recently asked about setting up two routers in series as routers, one wireless one not. It was my understanding that the computers on the second router would not be visible to computers on the first router, the wireless one. My assumption was that this would make it more difficult for someone who got access to the wireless router to also access those computers on the second router.
View 3 Replies
View Related
Dec 28, 2010
I just discovered that my wireless download speeds are 5Mbps, compared to 16Mbps if my laptop is connected directly to the modem or wired through the router. Uploads are 2Mbps either way. I have a WRT54GS v.6 with firmware version v1.52.8 which I updated today, completed by setting factory default through the router webpage after I discovered this discrepancy. The firmware update did not improve the download speed appreciably, if at all.Should the wireless connection be that much slower than the wired connection through the router? If not, what sort of issues could I be having to account for this?
I did just replace my modem when I discovered I was having erratic speedtests and that corrected that problem. That is when I became aware of the wireless issue, so not sure how long that has been the case. I have Charter's 16/2 HSI, living in a sparsely populated area with solid internet service. There is no external nor internal interference on this 2.4Ghz band.
View 8 Replies
View Related
Nov 6, 2011
I have a Arris DLS with 12 Mbps Download and when I Connect my laptop directly I get the same speed as 12 Mbps but when I do the speed test with my linksys I get only 5 Mbps. How to upgrade to the new WRT54GL or WRT54GS?
View 1 Replies
View Related
Apr 29, 2013
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 0.4 v0005.0 Build 130217 Rel.62075n
ISP : TM Streamyx
I have internet speed : 8Mbps.
The status of Internet in the modem config as foloows:
UpstreamDownstream
Current Rate (Kbps)636 10240
Max Rate (Kbps) 900 23412
SNR Margin (dB) 12.8 23.5
Line Attenuation (dB) 8.1 1.1
Errors (Pkts) 0 0
from the above informations the upstream is 636 Kbps but when I did the speed test it show me that the upload not more than 300 Kbps.
I used another modem D-link modem and the upload is more than 550 kbps when I used speed test.
Actually the upload is very slow by using TP-link modem and when I used another modem the upload is double speed.
View 1 Replies
View Related
Feb 25, 2011
I have FiOS and their supplied wireless router Actiontec #MI424WR. I have home theater equipment that uses the newer N signal so I purchased a Linksys E3000 Wireless-N Router. I have one of the LAN outputs on the Actiontec feeding the Linksys input and Wi-Fi turned off on the Actiontec. This is working good for my wireless home theater equipment but I am having problems with my wired speed. It has gone from averaging anywhere from 20 to 30 mbps on numerous test sites when plugged into the Actiontec to averaging around 10 mbps when plugged into the Linksys.
1) Is my wireless N speed going to top out at 10mbps or less since that is all the router is showing on wired? Shouldn�t N be broadcasting a faster speed if given the ability?
2) I have my computer currently plugged directly into the Linksys verses the Actiontec. This makes it easier to program the Linksys router. Since I am no longer using the wireless part of the Actiontec there really is no need to be plugged into it. Is there anything I can do get the speed higher on the Linksys, a setting I can change? Will I have to plug the computer back into the Actiontec to get the higher speed and then move it every time I may need to make a change to the Linksys?
View 2 Replies
View Related
Apr 10, 2013
I bought the new E2500 Router about 5 months ago and it was great until one day the wilreless part would not give me any speed at all. I ran a wired test of the router and I would get full 30Mbps speed that I'm supposed to get. So after firmware updates and everything else I took it back and got another one.It has worked great for a month and today it's now doing the same wilress slow down issue. I can run a lan connected test and get full speed. But wireless is bouncing around at 5Mbps~13Mbps. No where near the 30Mbps I'm supposed to be getting. What is causing the wireless to bomb like this?
View 1 Replies
View Related
Dec 6, 2011
I have a problem with new E4200 WAN speed. I have 1Gb connection from my ISP, and my old Netgear router gives me about 350 Mbps WAN speed, but with new E4200 I only got 110 Mbps max download speed.Cisco live support tried suggested to change MTU from Auto to 1400 (and try different wlan channels, even that I don't use wlan). This MTU size change makes no difference with WAN speed. I have latest firmaware installed, router reseted several times, tried different cables etc. Also with same cable sets my old Netgear still gives about 3 times better WAN speed.WAN port (and all LAN ports) seems to negotiated at 1000 Mbps at both ONT (optical network terminal) and Linksys settings page, but unfortanately there is no way to change the setting from auto to manual at E4200 settings (and it is not possible to change any settings of ONT by user). I was thinking that if somehow it won't auto negotiate properly (even if the setting page says its ok) but maybe it actually negotiated 100 Mbps port to WAN.
View 9 Replies
View Related
Oct 21, 2011
I just purchased an e1200 wireless router. Wireless speeds seem to be very slow. I'm trying to transfer 1 file to my media server, and am only getting 221kb/s. Also, internet connection seems to be slow as well (though if I plug directly into the router or the modem, I get speeds of 25Mbps, however when connecting wirelessly via the router I get speeds closer to 2Mbps (according to speedtest.com).I've played around with the settings as per other posts, and seemed to get the best speeds with the following config (however it is still very poor):
- security mode: WPA2 Personal
- network mode: B/G (have also tried N, which gave worse speeds)
- channels 1,3,6,9, and 11
View 2 Replies
View Related
Jan 2, 2013
I am using WRT54G linksys router. When connwcted through the router my download speed is very slow(~700K). If i plug in the LAN calble directly to my laptop the speed is ~4M
View 2 Replies
View Related
Jan 25, 2013
I bought a EA 3500 router and my speed is going only half the speed it was without the router.I have charter 100 meg internet, and a alienware Pc with a gigabit card.I wa going 100 megs and now I am at 38-50.I have tried hard reset with the bottom button, I have turned off all firewalls, I have changed my MTU to 1400 and 1500, I have went to speedguide.net and ran a optimizer., I have tried just about everything I can think of. firmware is up to date.
Is there anything I am missing, or am I not going to get these speeds with this router, I was told when I bought it, it was what I needed, Was I duped?, or is there just some setting i need to fix i am not aware of?
View 1 Replies
View Related
Nov 6, 2011
The smile was big when I bought my new Linksys E2000 Wireless Router.
Unfortunately the smiled stiffened when I realised that the network speed did not meet the expected up to 300 Mbps for Wireless and x10 for a Giganet connection. What to do to improve the LAN speed to an acceptable level ?
Network:
* Linksys E2000 ; WPA2 (Personal)
* x2 Windows7 Laptop ; x1 Linux Laptop ; x1 Qnap TS-409 Pro
* Download speed WiFi (between laptops as well as from NAS) <2MB/Sec
* Download Speed Cable (between laptops as well as from NAS) <8MB/Sec
* Download speed with direct connection to NAS (without switch) ~13 MB/sec
View 9 Replies
View Related
Nov 22, 2012
If I am wired to my WRT160N I get close to 50 Mps when I go wireless I get half of that speed and apparently there is nothing to change or to improve at the wireless settings.Some said that this is totally normal for wireless, have 1/2 of the wired speed.
View 9 Replies
View Related
Jun 29, 2011
My transfer speed from HDD which connected to linksys e4200 reach max 2,3MB/s how it is possible to watch fullHD movie if its required minimum 5MB/s? Maybe I should make some adjustments? HDD-WD My Passport 750Gb Also connection speed max reach 144mb/s?? how to make 300mb/s ? wifi adapter is Intel advanced N + WiMax 6250 AGN last driver installed, also E4200 last firmware installed 1.0.0.2 all settings by default Max download speed 75Mb/s by utorrent but provider gives 100Mb/s By cable its ok, max speed 100Mb/s as giving provider
View 9 Replies
View Related
Jun 30, 2012
Both the router and modem are new. Connecting directly to the modem I get Mbps, but the router speed is Kbps. I upgraded the firmware and made various changes per Google searches
View 2 Replies
View Related
Mar 22, 2013
I just setup an EA4500 last night and found the downlaod speed became 1/10 of my previous E3200 before. I tried to use different channels & 20MHz only for wireless connection but no success. The wired connection through Ethernet port was in the same low speed. What else should I try?
View 7 Replies
View Related
May 25, 2011
I have the WRT160N. Using [URL], I can get 2.5Mps from wired ports, but less than 0.5 Mps using the wireless.
View 9 Replies
View Related
Feb 26, 2011
I have brand new Cisco E4200 and WD Passport 500Gb.When it connected to router wireless (802.11n 300Mbit/sec) file transfer speed is around terrible 3 MB/sec. Same hard drive directly connected to my Mac Book Pro Unibody produce 30MB/sec. However my internet connection thru the router fairly shows 12MB/sec.It sounds funny, but for me is 4 times faster to download file from the Web rather the from hard dive that I'm holding in my hand.
View 5 Replies
View Related
Aug 12, 2012
I have this WRT54G wireless router and I just updated the firmware and everything. But I ran a speed test and the wireless speed is less than half the speed when I connect my pc to the router with a cable. i.e. I have a 32 Mb connection and with cable I get +31 Mb, but with wireless I barely get 13 Mb.
View 9 Replies
View Related
Aug 7, 2008
I've recently purchased a WRT160N router, and I'm using it in conjunction with a WMP54G wireless PCI card. I've set the router up to my requirements, and can get a stable wireless connection.. but internet speed seems excessively slow. While I'm able to get up to around 4MB/s transferring files over the network, running speed tests, it consecutively shows my download speed to sit around 400KB/s, whereas I'm able to get a steady 1.1MB/s on another desktop that is wired. Disabling the LAN adapter on that computer, and connecting via wireless, brings down the speed that that computer is able to get to around 400KB/s as well. Hence, I don't think it's my wireless cards, but something to do with the router itself.I'm also experiencing lag spike issues in online games, which I can only attribute to the current wireless setup, because I've previously had no issues with it. All relevant ports are forwarded, so that is not an issue.After doing some Googling on the subject, someone had suggested running SpeedGuide's TCP Optimizer, and changing the RWIN - I ran it, and set it to the 'optimal' settings, and after a reboot the wireless seemed fine - I was getting just a tad under what I should (about 950KB/s).. but after a short while, it just went back to 400KB/s. After further investigation, it seems that Vista automatically changes that RWIN value to optimize network traffic.. but I never had this issue with my old wireless gear, so I can only assume that the way Vista is reacting is based on the way the router is interacting with it.
View 9 Replies
View Related
Dec 5, 2012
I have had a EA3500 router in front of a 3Mb ADSL connection for about 6 months. This delivered essentially the same WAN performance as the WRT54G (v5) I replaced with it. Either router would get 2.4-2.8Mbps through a variety of speed test sites, inlcuding the CCC builtin speed test.I upgraded to a 10Mbps cable internet connection today, but the EA3500 won't deliver any more speed than with the old ADSL connection. The reason I am blaming the EA3500 is that if I plug my computer directly into the cable modem, I get a solid 9.9Mbps down/0.99Mbps up, which is exactly how my line is provisioned. With the router in place and active, I get the same slow WAN connection, 2.8-2.9MBps, whether using a PC connected with GigE, a PC connected via Wireless-N, or with an iPhone. This all implicates the EA3500's WAN connection.
Is there anything that can be done do let the EA3500 work properly? I upgraded my firmware today in hopes that that would change something. But, I get the same speed with the latest firmware (1.1.39.145204) as I did with the previous version. Speed across my wired LAN is excellent; I can sustain 70MB/sec from my PC to my NAS. It's only the WAN connection that is performing poorly.I can downgrade to the non-CCC firmware if that would make a difference; would it?
View 4 Replies
View Related
Jan 19, 2013
I came home yesterday and my Internet was really slow. I later found out that it was due to my Linksys E3000 because if I bypass my E3000 and go directly to my cable modem, it work just fine.I tried reconfigure, update firmware, factory reset and none of these has worked.
View 8 Replies
View Related
Aug 3, 2012
So I went out and bought a brand new EA4500, because I thought my old router was bad due to horrific wifi Speeds on my Wireless devices like my laptop and Samsung Galaxy S3. Well now I have the same issue with this new router.My speed from comcast straight from the modem is 25mbps down and 5mbps up, on the routers through a wired connection I get the same thing. As soon as a switch over to Wireless my connection goes from 25mpbs/5mpbs to less then 2mbps down. I've reduced the MTU, and I've tried turning off QoS. Nothing seems to work
View 9 Replies
View Related
Apr 23, 2013
I have purchased Linksys WRT320N because my ISP give me speeds of 400 mb/s download and 200 mb/s upload. After I tested the speed my router get only 137 mb/s, why is that? I paid for gigabit router!?
View 7 Replies
View Related
Jan 4, 2013
I usually download and update on my Nas in my house. I conneting my nas to the e4200. My laptop get full wifi from my router, but the speed up and down is very slow. I setup the wireless everything is auto.
View 1 Replies
View Related
Jan 15, 2012
I have the WRT160N. Using speed test.net, I can get 2.5Mps from wired ports, but less than 0.5 Mps using the wireless.
View 1 Replies
View Related
Mar 5, 2012
I bought a brand new Linksys E1200 v2 and I encountered a big problem.
Without the router I am able to reach over 90 Mbps doawnloading torrents on wired connection, but through the router I can't obtain more than 55 Mbps.
Is the problem in settings or that's just the maximum speed that the router can handle for wan2lan ? Do I need an upgrade?
View 2 Replies
View Related
