I just setup an EA4500 last night and found the downlaod speed became 1/10 of my previous E3200 before. I tried to use different channels & 20MHz only for wireless connection but no success. The wired connection through Ethernet port was in the same low speed. What else should I try?
View 7 RepliesSo I went out and bought a brand new EA4500, because I thought my old router was bad due to horrific wifi Speeds on my Wireless devices like my laptop and Samsung Galaxy S3. Well now I have the same issue with this new router.My speed from comcast straight from the modem is 25mbps down and 5mbps up, on the routers through a wired connection I get the same thing. As soon as a switch over to Wireless my connection goes from 25mpbs/5mpbs to less then 2mbps down. I've reduced the MTU, and I've tried turning off QoS. Nothing seems to work
View 9 Replies View RelatedBoth the router and modem are new. Connecting directly to the modem I get Mbps, but the router speed is Kbps. I upgraded the firmware and made various changes per Google searches
View 2 Replies View RelatedI usually download and update on my Nas in my house. I conneting my nas to the e4200. My laptop get full wifi from my router, but the speed up and down is very slow. I setup the wireless everything is auto.
View 1 Replies View RelatedI just bought this router and set it up using its CD. It looked like everything was fine until I connected my laptop using wireless. The wireless download speed is absolutely ridiculous. My wired desktop shows 35mbps while my laptop is 0.5mbps. Upload is same for both. Clearly something is limiting my download wireless.
Contacted Cisco support and they told me to change the mtu to 1400, change channel to 11 and reboot. Nothing worked. I have the latest software.
Transfer speed for sending or receiving files from a USB external HDD connected to the router is slow? Speed ranging from 2MB - 4MB/s. The HDD is definitely capable of at least 80MB/s if plugged directly into the PC. Is it meant to be this slow or there's a fix somewhere which I'm not aware of? Thought it's suppose to be the top of the line products but seems so inferior if I were to compare with other high end routers in the market which performs better, faster and definitely much cheaper.
View 9 Replies View RelatedIm trying to optimize my E4200 settings and Ive noted that ping and download speeds are extremely slow for the internet service I signed up for. Ping speeds are consistently more than 1000ms and dowload speeds typically are less than 3Mbps. These are for both wireless and wired connections to the E4200 router.
When I disconnect the router and hardwire my laptop directly to the the modem, ping speeds are less than 100ms and download speeds are 20Mbps.
Simply put, webpage loading is at a snails pace with wireless and wired connection the router, but blazing fast when hardwired directly to the modem.
On a seperate issue, the iMac I have is also **bleep** slow even when hardwired directly to the modem. Is there an obvious router setting Im screwing up? Router is updated with the latest software.
I Have BT Infinity and they are pushing 70mbps to my house ....i bought an EA6500 and i had real bad internet speed but amazing conection speed with my BT Home HUB3 ... 23Mbps with Cisco EA6500 and 68Mbps with my BT Home Hub3. I found out it was the Media Prioritization so just to be safe i reset my factory settings and made sure it was turned off. Just like magic i get the same now as the BT Home HUB3 .
View 1 Replies View Relatedi have WRT610N v1.0 with latest original firmware but ftp upload speed and torrent download speed is terribly slow.
View 3 Replies View RelatedI am getting very slow download speeds on my wireless router (Linksys model#WRT160N). I measured it on speedtest.net. with my ASUS laptop, ASUS Transformer Prime tablet, and 2 Ipod touches. All similar speeds.
-Download avg: 1.30 Mbps
-upload avg: 6.20 Mbps
I measured my desktop speed that is hardwired through the router to the modem.
-Download avg: 30.00 Mbps
-upload ave: 6.20 Mbps
I have scanned all the wireless connection in my area and found them to occupy channels 1, 6, 11. I tried changing my channels one at a time for all 11 channels. Some did a little better than others but not a lot. Also, if I buy a dual channel router, can all wireless devices pick up on the 5GHz spectrim and if so, could this alleviate some interference? Is it possible that my router is going bad and a new single channel 2.4 GHz router will be fine? jasonmac73 has chosen the best answer to his/her question.Click here to view the answer that was selected.
Recently my desktop has experienced very slow download speeds (~0.11 Mbps), however the upload speed appears to be in line (~2.0Mbps). These numbers are taken from Comcast's speed test (my ISP). It is obviously a problem with my PC because everything else on the network (PS3, Laptop) have great signals with no problems. I just recently reverted the Desktop back to its factory state, and everything was working fine for a couple of months. The desktop in question uses Vista 32-bit and the Belkin Basic USB Wireless Adapter.
View 1 Replies View RelatedMy ISP recently upgraded my line to ADSL2+. I am still only getting 1.36Mbps download speed across WiFi but if I connect my laptop to the router with ethernet cable I get 8.59Mbps. Why is the router slowing down my connection so much?
View 1 Replies View RelatedI just discovered that my wireless download speeds are 5Mbps, compared to 16Mbps if my laptop is connected directly to the modem or wired through the router. Uploads are 2Mbps either way. I have a WRT54GS v.6 with firmware version v1.52.8 which I updated today, completed by setting factory default through the router webpage after I discovered this discrepancy. The firmware update did not improve the download speed appreciably, if at all.Should the wireless connection be that much slower than the wired connection through the router? If not, what sort of issues could I be having to account for this?
I did just replace my modem when I discovered I was having erratic speedtests and that corrected that problem. That is when I became aware of the wireless issue, so not sure how long that has been the case. I have Charter's 16/2 HSI, living in a sparsely populated area with solid internet service. There is no external nor internal interference on this 2.4Ghz band.
Ive bought recently WAG160n and Ive watched that I have problem with slow speed of WiFi. On LAN cable its ok. Internet provider gives my up 20Mb/sec. download and up to 1Mb/ses. upload. Ive visited
[code]....
I add, that my previous router: WAG200G on this same line gives me 14-16 Mb/sec. download on WiFi. Why upload speed is ok, but download not?
i have a laptop that i connect through our wireless router with, and for the past couple months my download speed have been terrible. my browsing speed is just as fast as it always was when i am connected to our router, just incredibly slow if i try to download or stream something.however, my downstairs neighbor also has a wireless router set up that i can access which gives me incredible download speeds but my cant even browse the internet because i the browser connection times out.i have tried plugging directly into my router to on the thought that perhaps the 2 routers' wireless was somehow interfering with each other, but my download speeds are still *** even then.
View 1 Replies View RelatedWe have a 861 router for our small office with 15 people. We have been experienced download problems for several months, but we have suspected the internet supplier to be the bottleneck as we have a new 861 router with the default configuration from the "Cisco Configuration Professional Express".
The sympton is that the download speed over http starts fast, but drops after a few seconds from 10MB/s to 3KB/s and stays there. The internet supplier came here today and made some tests. So we downloaded some huge files over the direct cable, and it was staying at constant 10MB/s. When we connected over the router it started at 10MB/s and dropped down to 3KB/s.
Is there something that has been forgotten in the "Cisco Configuration Professional Express"?
I live in the tampa bay area, I have bright house (BHN) as my service provider, which provides a Road Runner Lightning (40/5) package. I previously used BHN's top tier (20/2) back in July (and prior) with no problems.
After converting to Lightning in August of this year (2010). Of course, BHN (and every other provider) wants to force a modem/router down your throat, so I had them bridge it (in short, turn it into a dummy modem with no routing). I had an SMC branded modem gateway at the time. I work from home 2 days a week (so I can spend more time with my kids during morning, lunch, right after work) and this requires me to use QoS to ensure my VOIP work calls don't get dropped, if the family is watching youtube videos or watching netflex.
My network was as follows SMC Modem >WAN IP>>WAN Port>>D-link DIR-655>>Switch Ports>PC1, PC2, PC3
Everything seemed fine (from a usability stand point) till about 2 weeks ago when my upload speed seemed to grind to halt. Normally I was able to upload about 200-300K per second, and I noticed this dropped to about 45K per second during a drop box upload. First thing I did was power cycle both my modem and router (in the proper/usual order). After they both come up, I start using speed test to find out what my upload speeds were. I was getting about 39Mbps down, but only .56Mbps up still. I factory reset my router.... test, similar speeds. Power cycle all computers (just in case), and then modem/router. Tested, similar speeds. Updated the firmware to the latest. Same issue
Called BHN customer service, they factor reset it, but it wasn't in bridge mode. If I by passed the 655, in factory mode (non bridge mode) upload speeds returned to better than expected states. If I bridged the cable modem, upload speeds seemed to crash.
Had BHN replace the modem, seemed fixed for a day, then issue came back. Had them come back out and replace it again, this time with a Motorolla Surfboard modem... same issue. Fine during factory reset, however after they bridge the modem, upload speeds were fine. Told BHN I would take it from there.. Connected up the DIR-655, and upload speeds crashed again. (.6Mbps). Called D-Link Support, and the Chinese English speaking rep seemed to not be listening to me and tried to have me adjust my MTU as well as Wireless settings. Long story short... the rep was a level 0 id10t and I hope D-link will consider hiring better employees/contractors. So I was all about to give up and replace it with a DD-WRT capable router (which it takes me a lot to want to swap hardware), when I discovered the wan shaping was on. Which I thought to myself... nah... QoS has never messed up before... why would it be the cause. Turned off wan shapping... and voila. Issue seemed to be insta-resolved.
Unsatisfied with that... I decided to dig a lil deeper. I turned on Wan shaping again, but decided to set the settings manually instead of auto detect.
Here are the settings I used... (Advanced Tab>QoS)
Enable Traffic Shaping - Checked
Automatic Uplink Speed - Unchecked
Manual Uplink Speed - 5000
Connection Type: Cable or Other Broadand Network
Enable QoS Engine - Checked Automatic Classification - unchecked (this checked seemed to affect my upload speed by about 5-10% during testing) Dynamic Fragmentation - unchecked (this checked seemed to be the worse enemy for upload speed)
While I know I'm not any network guru (still have to use a subnet calculator for subnetting), I think I did a pretty good job drilling down the issue (once I got passed my service provider replacing modems).
Anyways, I've had overall good luck with D-Link products, even have a 5 port 10/100 switch (all metal) from 1998 that works great. Hopefully, D-Link will just either put more documentation on the web, or hire better employees.
Just bought a new DIR-655 Xtreme N Gigabit Router 3 days ago. Have 5MB fiber and consistently receive 4.7-5.0MB when connected directly to my laptop (windows XP, Dell wireless 1390 WLAN Mini-card, 802.11g only). I followed the CD instruction to set up the router and when connected wirelessly I consistently get 2.4 - 2.7 MB. When I connect a cable from the router to my laptop, I get the 4.7 - 5.0MB that I get when connected directly. I've tried a second laptop (Vista, 802.11g only) and when connected wirelessly I get 4.7-5.0 MB. A friend of mine who has a laptop (Windows 7, g/n) also connected at 4.7-5.0 MB.
View 1 Replies View RelatedI get 17 mbs download on one wireless laptop, only 7 mbs on the other wireless laptop. What should I look for to fix the slow laptop.The slow laptop is 8 feet from router with drywall wall between, the faster is 25 feet, no wall between computer and router.
View 1 Replies View RelatedI have a Arris DLS with 12 Mbps Download and when I Connect my laptop directly I get the same speed as 12 Mbps but when I do the speed test with my linksys I get only 5 Mbps. How to upgrade to the new WRT54GL or WRT54GS?
View 1 Replies View Relatedis there a link to directly download the EA4500 firmware?
View 3 Replies View Relateddell latitude d630 vista 32bit.why my download speed is very slow on wireless .i had 2 laptops running speedtest together my friends showed 13.5 mps mine was woefully slower at 1.3 mps, sometimes it shows high speed but then it runs that slow it stops internet running .
View 1 Replies View RelatedJust bought the EA4500, updated with the latest cloud firmware. but Wan performace is BAD. download with router 31.56Mbps, without approx 120 Mbps, tried changing MTU from auto to 1470 but no succes.
View 9 Replies View RelatedI just installed my EA4500 and my connection speed dropped from 20 mbits/s to around 3 or 4 mbs/s.When i connect directly with the modem, the speed gets back to normal.
View 2 Replies View RelatedBought the new EA4500 a couple of days ago and have looked at my wireless connection and see it varies from 72Mbps to 144Mbps. It has jumped up to 270Mbps a few times, but rarely. Shouldn't it be 300Mbps most of the time? My laptop is 4 feet away from the router and the router is on top of a card board box being elevated away from interference. The prior router was a dlink 855 that went whacky after 3 years. I believe I was usually at 270 Mbps with that. What gives? Do I have a faulty router? With this new router, I expected the range to be a lot farther and faster too, but it is not in my family room. 2nd floor router, family room is 1st floor about 50 feet away and I get 1Mbps - 5Mbps. Everything is set to Auto on router and IP6 is disabled on laptop.
View 9 Replies View RelatedI just upgraded my E4200v1 router to a new EA4500. The install process went fine and I'm running firmware 2.0.37.When I was running the E4200v1, I had wireless speeds of 24-30mbs. Since upgrading to the EA4500, I only have 5-8mbs wireless speed.
View 3 Replies View RelatedI upgraded from a E2000 to a EA4500 today and I am experiencing slow wired WAN speeds. On my E2000 I get approximately 60Mbps down and approximately 2Mbps up, and when switching over to the EA4500, I can only manage about 20Mbps down and about 2Mbps up. I can switch back and forth between routers and replicate the results every time
View 7 Replies View RelatedI bought a new EA4500 and it was working great and now about 8 hours later it is won't even download some websites and is working very slowly. Pandora suddenly no longer works on it and neither does ESPN, it just times out. Very, very slow. I am very disappointed. I am using it with my Verizona westell DSL modem ... Why this is happening or if maybe this router is defective.
View 9 Replies View RelatedI own a ea4500 wireless router, I have tested the speed at speedtest.net and wirelessly I get around 9 mbps. My speed is 23 mbps when I hard wired the pc. I have check the speed on a tablet ( android ), pc and a mac to about 5 feet away from the router with no walls or anything between the two devices.I have checked all the settings but I don't see anything wrong, I have changed to N mode only to make sure I use top speed.All my devices are able to use N.
View 3 Replies View RelatedIn 'Status' on my router there is a green dot in the field below 10/100 mbps at 'Internet port speed' - shouldn' that dot be below 1 gbps?
View 1 Replies View RelatedI have Verizon DSL. Since I've gotten it turned on in my new apartment it's been randomly DCing, I had a tech come out and tell me it was because I'm too far from the central office(thought I'm only a mile from the office?) and I needed to call and get my mbps reduced from 10, to 5. So, I called and did that and I was still having the same issue. Today another tech came out, told me the same thing, but I needed to be reduced to 3, and left. I called and got it reduced again. They said it should be 3-5 and I was at 5-7. So, now my download speed is actually higher than it was when I was 5-7(it was at 3 mbps usually, now it's 5), but my ping has doubled. Pages are taking longer to load, and when I play any games online there's a noticeable delay. I have been DCing less often, but it's still happening.
View 14 Replies View RelatedI have been using a Lenovo W510 laptop with an Intel wireless adapter (Intel(R) Centrino(R) Ultimate-N 6300 AGN). The download speed has been 15-18 mbps on my home network. I just bought a new Lenovo W520 with a Lenovo wireless adapter. The download speed is about 1 to 1.5 mbps. What changes should I make to the router settings so that it communicates properly with the Lenovo wireless adapter?
View 9 Replies View RelatedI have searched the forums, and can see that I am not the only one with speed problems on this router. When I changed from a D-link dir-615 (yeah, no wonder I changed it ) my download speed dropped from 4-5 MB/s to 1,3 MB/s. I'm using a wired connection. Have tried disabling QoS in router settings, did a firmware upgrade, reset the router. You see, when I do speed tests on the internet I get 40-50 mbits download, 25-30 mbits upload. I have tried many different files to download, both torrents and through my browser.
View 2 Replies View Related