Linksys Wireless Router :: Getting Download Speed On WRT600N?
Jul 14, 2011
I have been using a Lenovo W510 laptop with an Intel wireless adapter (Intel(R) Centrino(R) Ultimate-N 6300 AGN). The download speed has been 15-18 mbps on my home network. I just bought a new Lenovo W520 with a Lenovo wireless adapter. The download speed is about 1 to 1.5 mbps. What changes should I make to the router settings so that it communicates properly with the Lenovo wireless adapter?
I just discovered that my wireless download speeds are 5Mbps, compared to 16Mbps if my laptop is connected directly to the modem or wired through the router. Uploads are 2Mbps either way. I have a WRT54GS v.6 with firmware version v1.52.8 which I updated today, completed by setting factory default through the router webpage after I discovered this discrepancy. The firmware update did not improve the download speed appreciably, if at all.Should the wireless connection be that much slower than the wired connection through the router? If not, what sort of issues could I be having to account for this?
I did just replace my modem when I discovered I was having erratic speedtests and that corrected that problem. That is when I became aware of the wireless issue, so not sure how long that has been the case. I have Charter's 16/2 HSI, living in a sparsely populated area with solid internet service. There is no external nor internal interference on this 2.4Ghz band.
I have searched the forums, and can see that I am not the only one with speed problems on this router. When I changed from a D-link dir-615 (yeah, no wonder I changed it ) my download speed dropped from 4-5 MB/s to 1,3 MB/s. I'm using a wired connection. Have tried disabling QoS in router settings, did a firmware upgrade, reset the router. You see, when I do speed tests on the internet I get 40-50 mbits download, 25-30 mbits upload. I have tried many different files to download, both torrents and through my browser.
I have tried all the speed test sites and tried downloads with and without my EA2700. Every test shows about half the perfomance when connected through the router. My speed tests at speedtest.net with a direct connection are in the 21-26Mbps range, the same tests run about a minute later through the EA2700 fall in the 10-12Mbps range with spikes up to 17Mbps.I've reset the router and modem.I've gone back to the 22.214.171.124982 Firmware (which it's currently on)I've set the MTU everywhere from 1400 to 1500 (literally EVERY setting for at least a couple of hours) it is 1492 currently. None of these have worked. In addition, when a large stream starts, such as a Steam download, I will lose ALL connectivity. Going in to Network and Sharing and clicking to connect to the internet restores the connection, no need to reset any hardware (which is odd in itself). I have had MANY routers over the years and I've all but exhausted support with service provider as the connection is solid if I eliminate the router.Main machine is a Windows 7 Home edition Total of 5 machines, 3 of which see regular use All machines go through a Trendnet 16 port switch and performance is the same direct or through the switch I m on Brighthouse in Central Florida and have all but exhausted their support.
my Linksys E3200 router is somehow slowing my internet download speed by a lot. Direct wired connection from computer to modem gets me around 200Mbps download speed, but if I connect thru my Linksys E3200 router (wired connection, not wifi), the download speed goes down significantly to ~70Mbps. The E3200 is only connected to the modem and my computer (i.e. I have unplugged all other devices from the E3200 router). Are there setttings in the E3200 that can potentially cause it to limit the speed or could this be caused by something else?
I just setup an EA4500 last night and found the downlaod speed became 1/10 of my previous E3200 before. I tried to use different channels & 20MHz only for wireless connection but no success. The wired connection through Ethernet port was in the same low speed. What else should I try?
I have WRT160N router and am not sure if I have a connectivity problem or a setting issue. I've done a speed test with speakeasy.net and get fine through the hard wire desktop (25.16/3.77) but when I do it on my wireless laptop I get 2.03down / 3.66up. The speeds were basically the same right next to router as it was 40' away.
I bought a E1200 and have it hooked up to my Comcast internet.. When I have my computer hooked up directly to the modem I get a 30mbps download speed. When I connect it to my router the download speed crashes to about .5-.75mbps.. My upload stays pretty stable at around 6-7mbps.
I usually download and update on my Nas in my house. I conneting my nas to the e4200. My laptop get full wifi from my router, but the speed up and down is very slow. I setup the wireless everything is auto.
I use steed test appnto check the speed of my wireless. I am connected to 5ghz band and using the app most of the time my download speed are between 10-20 Mbps (red line range in app). I noticed that some posts are referring to download speeds of 50mbps. Are my download speed too low? I am in ontario cogeco isp
I just bought this router and set it up using its CD. It looked like everything was fine until I connected my laptop using wireless. The wireless download speed is absolutely ridiculous. My wired desktop shows 35mbps while my laptop is 0.5mbps. Upload is same for both. Clearly something is limiting my download wireless.
Contacted Cisco support and they told me to change the mtu to 1400, change channel to 11 and reboot. Nothing worked. I have the latest software.
Im trying to optimize my E4200 settings and Ive noted that ping and download speeds are extremely slow for the internet service I signed up for. Ping speeds are consistently more than 1000ms and dowload speeds typically are less than 3Mbps. These are for both wireless and wired connections to the E4200 router.
When I disconnect the router and hardwire my laptop directly to the the modem, ping speeds are less than 100ms and download speeds are 20Mbps.
Simply put, webpage loading is at a snails pace with wireless and wired connection the router, but blazing fast when hardwired directly to the modem.
On a seperate issue, the iMac I have is also **bleep** slow even when hardwired directly to the modem. Is there an obvious router setting Im screwing up? Router is updated with the latest software.
I Have BT Infinity and they are pushing 70mbps to my house ....i bought an EA6500 and i had real bad internet speed but amazing conection speed with my BT Home HUB3 ... 23Mbps with Cisco EA6500 and 68Mbps with my BT Home Hub3. I found out it was the Media Prioritization so just to be safe i reset my factory settings and made sure it was turned off. Just like magic i get the same now as the BT Home HUB3 .
I just "upgraded" from an E1000 to an E1200 wireless router. I had good performance with the E1000, and I only upgraded to the E1200 because it was on sale.My only complaint with the E1200 is the slower download speed on my desktop PC that is connected directly to the router. My normal download speed on the desktop PC was 25 Mbps with the E1000 model. After I disabled the WMM on the E1200 as others suggested, the download speed on the desktop machine immediately increased from 5 Mbps up to 15 Mbps. Any other suggestions to get the download speed up to 25 Mbps before I switch back to my E1000? The E1200 router is connected to my Arris TM602G modem. Both modem and router were reset during the installation process. I setup parental controls for a couple of iPods and configured Open DNS, but other than that, the router is using default settings. All wireless devices in the house seem to be performing fine with the E1200.
My problem occurs when i am trying to download something big, mainly the speed of the download raises at a peak and then it drops disconnecting me from the internet for a few seconds. This only happens when my laptop is on a wireless connection and this phenomenon repeats itself untill the download is complete. During the connection crash I am not able to access any site.
My laptop is an Asus G series with Win7 64bit SP1, and I use utorrent for P2P downloads.
I have a WRT600N dual band router and have only been able to connect to the 5Ghz when it's network mode was set to mixed. I also have a Dell Wireless 1505 Draft 802.11n WLAN Mini-Card. When setting the Network mode on my router to Wireless N-Only I am unable to connect to the network. I have been searching all over the internet for how to fix this, but none of the answers suit me. I have my network security set to WPA2 with an AES encryption, like people keep saying so I know that is not the problem. Others say that I need to set my wireless adapter to N-Only as well, but I have not been able to find anything in Google that shows me how this is done. The driver version for my adapter is 126.96.36.199 and is up to date according to Windows.
I have a Telus modem, that is hard wired to a siemens wireless router.The telus modem assigns addresses to the siemens router in 192.168.254.* address range.There are a lot of other siemens routers operating in my neighbourhood and I keep getting kicked off.So I want to connect my MacBook Pro wirlessly through the linksys WRT600N on the 5GHz band.I've disabled the 2.4Ghz band.
I'm having problems with the access restrictions feature on the WRT600N. I do have the latest firmware upgrade, which was released in 2008 I believe. Anyways whenever I totally block a PC from the internet either by MAC or by IP, it affects the internet on the rest of the house. Logins to sites do not work right. Logouts from do not work right. Different features of different sites will not work properly. There also will be a lag sometimes when entering the url for a new site. But as soon as I turn the access restriction off, everything goes immediately back to how it should be working.
I have a WRT600N router. I have one PC that is connected to the router via a wired connection. I also have an iPad (3rd generation) that is connected to the router via a wireless connection. On my PC, I went to speedtest.net and determined that I am receiving like 20MB downloads via the wired connection. However, my iPad only gets approximately less than 2 MB download speeds. I have tried reseting the router and I do have what I believe to be the latest firmware update (Firmware Version: 1.01.36 build 4). I also receive the slow download speeds when I try connecting the other wireless devices. I assume my problem has to do with some sort of configuration setting found in the router configuration page (http://192.168.1.1/). The router is only a few feet away from my iPad so the signal strength is strong. I just don't understand why I'm receiving such slow wireless download speeds.
I cannot upload files through http (e-mail attachments, send images to Facebook, send file to virustotal.com) with Linksys WRT600N router. When I remove connection cable from router and place directly in a computer, everything works just fine. I am using last firmware upgrade.
I fought my ISP (frontier) for weeks trying to get their 7500 DSL/modem/router configured in bridge and working into the WRT600N. Finally gave up and put a new Engenius EVR100 behind the 7500 bridge and it came up fine in 10 mins. Now I would like to use my old WRT600N downstairs as a second router and run it in the range of the Engenius DHCP, with DHCP turned off in the WRT600N.
My question is this ... Do I set the WRT600N as a static IP address and use an address in the range issued by the EVR100?And, if so, what would the sub-net mask, default gateway and DNS numbers be? Also would the router address itself (lets say I use 192.168.0.120 from the EVR100 range) be different then the static IP address?
My DSL Modem connected right now to Linksys Model: WRT600N (Dual Band Wireless-N Gigabit Router) to give a wireless internet access in my house. I have TWO spare Linksys Wireless Router (WRT350N-Wireless-N Gigabit Router) and (WRT54G2-Wireless-G Broadband Router) that I need to use to expand my wireless network at home.
How can i connect the two routers to became an access point or range expander to existing router. It is possible the two spare routers became an access pt or expander? How can i configure that? Cable configuration?
When the Wrt600N came out, it was said that the "Reserved" button would be enabled by a future firmware upgrade to support WiFi Protected Setup. Surely in the three or so years this has come to pass.Does anyone have a link to information on using WPS with the WRT600n?
I am getting very slow download speeds on my wireless router (Linksys model#WRT160N). I measured it on speedtest.net. with my ASUS laptop, ASUS Transformer Prime tablet, and 2 Ipod touches. All similar speeds.
Download avg: 1.30 Mbps upload avg: 6.20 Mbps
I measured my desktop speed that is hardwired through the router to the modem.
Download avg: 30.00 Mbps upload ave: 6.20 Mbps
I have scanned all the wireless connection in my area and found them to occupy channels 1, 6, 11. I tried changing my channels one at a time for all 11 channels. Some did a little better than others but not a lot.Also, if I by a dual channel router, can all wireless devices pick up on the 5GHz spectrim and if some, could this alleviate some interference?Is it possible that my router is going bad and a new single channel 2.4 GHz router will be fine?
I am using a linksys wrt600N with easylink advisor version 1.6.0042. I am trying to install a video camera and the instruction manual says under "known issues": LinkSys routers have a factory default setting in the firewall menu called "filter anonymous internet requests". If you want to access your camera from the internet you have to uncheck this option."I see this option in the WRT600N manual, but it references a software choice that I don't have.I have gone to the website and downloaded the latest compatible software version, and I still don't have the choice to uncheck this option.
I have the latest flash installed. I am making use of all the options available to this router. USB drive set up as a file server, both radio bands have devices which attach. All wifi security is wpa2 with a complex key string. Also have pc’s attached to all lan ports. I also have all the wireless devices registered on the mac address filter for access set to enable/allow. I have a total of 9 mac address in the list. One lan device is on the DMZ. One address is reserved. Not sure what other details you need.Router is used for online gaming, video streaming, and typical internet browsing.
I just ran some speedtests om my PC on the advice of my isp to see if my Linksys WRT54G router might be bad. As a result, I found that the router might not be entirely bad, but it might not be entirely good, either. I got .77 Mbps dowload and .17 Mbps upload on the first speedtest. I got .43 Mbps download on the second speedtest and the speed test hung hear the end. When I connected an IMac to the cable modem with an ethernet cable, the IMac ran strong. So the tech thought I should get a new router.
But wait a minute, isn't there a network adapter in the PC that the router talks to? Might the adapter be the problem, not the router? So I speedtested the wireless network to the IMac. That speedtest was fine, tiptop, like the ethernet direct connection test noted above. Did that tell me that the problem is in my PC network adapter, not the router? Then, I retested (speedtested) the connection on the PC and it was fine...excellent. Good up and down speeds, no hangs.Then, I checked the PC adapter (a Belkin). I saw three adapters on Device Manager, including the Belkin. I downloaded new drivers for the adapters (except for the Microsoft Virtual WiFi Minipoty Adapter - because it got a warning that the download software wasn't signed and might harm my computer).
The standard Verizon router doesn't have Wireless N capability, so I got the WRT600N (first floor) a while back and connected it to one of the ports on the Verizon router (basement). I have the wireless turned off on Verizon router. My problem is that anything connecting to the WRT600N has extremely intermittent connectivity.
Ok, so I reset the router but i still can't login to the setup using the factory password (admin/admin) (blank/admin) (admin/blank). Now I have an unencrypted network and no access to the setup... I even tried using the setup CD but it doesn't recognize the router.