I bought a new EA4500 and it was working great and now about 8 hours later it is won't even download some websites and is working very slowly. Pandora suddenly no longer works on it and neither does ESPN, it just times out. Very, very slow. I am very disappointed. I am using it with my Verizona westell DSL modem ... Why this is happening or if maybe this router is defective.
View 9 RepliesJust bought the EA4500, updated with the latest cloud firmware. but Wan performace is BAD. download with router 31.56Mbps, without approx 120 Mbps, tried changing MTU from auto to 1470 but no succes.
View 9 Replies View RelatedI just installed my EA4500 and my connection speed dropped from 20 mbits/s to around 3 or 4 mbs/s.When i connect directly with the modem, the speed gets back to normal.
View 2 Replies View RelatedI just setup an EA4500 last night and found the downlaod speed became 1/10 of my previous E3200 before. I tried to use different channels & 20MHz only for wireless connection but no success. The wired connection through Ethernet port was in the same low speed. What else should I try?
View 7 Replies View RelatedI upgraded from a E2000 to a EA4500 today and I am experiencing slow wired WAN speeds. On my E2000 I get approximately 60Mbps down and approximately 2Mbps up, and when switching over to the EA4500, I can only manage about 20Mbps down and about 2Mbps up. I can switch back and forth between routers and replicate the results every time
View 7 Replies View RelatedSo I went out and bought a brand new EA4500, because I thought my old router was bad due to horrific wifi Speeds on my Wireless devices like my laptop and Samsung Galaxy S3. Well now I have the same issue with this new router.My speed from comcast straight from the modem is 25mbps down and 5mbps up, on the routers through a wired connection I get the same thing. As soon as a switch over to Wireless my connection goes from 25mpbs/5mpbs to less then 2mbps down. I've reduced the MTU, and I've tried turning off QoS. Nothing seems to work
View 9 Replies View RelatedI am only getting 10-14 mbps when I should be getting 30-35 (using the gigabit ports). I thought it might be my provider but today I connected my old netgear router and the speed was 32-34 mbps. Is there some setting that I should be looking at?
View 5 Replies View RelatedI have a problem with my new router. I connected't my iMac (27" 2010) and NAS Synology 1511. My problem is the slow connection between mac and router - only 100Mbit (ethernet port on mac is 1Gbit), strange thing... my NAS have 1Gbit with no problem, and the mac is not. I trying manual configure - forcing speed to 1Gbit, but then is no connection at all. I'm also trying changing wires, but no change. Im buying special ethernet cable cat 6 - also no change. Changing ports on router - result the same.
View 7 Replies View RelatedThe issue is that one Dell laptop is experiencing slow or no internet connectivity at all using wireless. Sometimes 1 to 2 minutes to load a page, other times the dreaded 'not able to display webpage' message. It's fine using Ethernet. I have another laptop (same exact brand/model) and it has no problems. I also have a Macbook Pro and other Apple IOS devices (iPod/iPads) that are fine. Several Ethernet connected devices are fine as well. The laptop in question had no issues with my previoius Linksys devices, which are a BEFSR41/WAP55AG as well as a WRT-54GS v2. This one laptop was fine the first day or two on the EA4500 but something happened which is causing this issue. I had to add the WAP55AG back onto my network so my son is happy again, but my plan was to decommission the other devices. EA4500 Firmware v.2.0.37Dell Inspiron 15 Notebook w/Intel Centrino Wireless N1030, 1x2 bgn (2.4 GHz) + Bluetooth
View 2 Replies View RelatedTransfer speed for sending or receiving files from a USB external HDD connected to the router is slow? Speed ranging from 2MB - 4MB/s. The HDD is definitely capable of at least 80MB/s if plugged directly into the PC. Is it meant to be this slow or there's a fix somewhere which I'm not aware of? Thought it's suppose to be the top of the line products but seems so inferior if I were to compare with other high end routers in the market which performs better, faster and definitely much cheaper.
View 9 Replies View RelatedI've set up PPPoE on my EA4500 router with a Vigor 120 modem in bridged mode and it says an internet connection is established, but the connection is extremely slow on all my devices. When I run the speed test within the EA4500 firmware it appears fine, but I cannot load any web pages on my laptop or other decives because the connection is so slow. The connection is slow with both wired and wireless connections. I've tried changing the MTU settings with no success. I've also tried using a different router and connecting the modem directly to my laptop and using PPPoE within the laptop and these both work fine, so I think it's clear there is a problem with the EA4500 router itself.
I'm just using the Vigor 120 to authenticate and connect to the internet itself, with the router in DHCP automatic configuration mode. I think this is causing a double NAT.
EA4500 was working fine for about 2 months.Now, its not so happy.Power indicator is on.Plug something into one of network ports - nothing, and no indicator LEDs are on.Plug an operational internet cable into it - nothing, and no indicator LEDs are on.
View 3 Replies View RelatedI thought that you're supposed to be able to type myrouter.local in order to get to the router BIOS. It does not work for me; instead it generates a Google search. Is there a way to get that to work?
View 5 Replies View RelatedThe ISP provided on the base is called Sniper Hill. The basic setup is there are CAT5e drops in every room. You plug in, and it is all web based to pay for and sign in to the service. Other people have successfully connected there routers made by other manufacturers, why won't the EA4500 connect? I've tried a lot of different ideas from reading different stuff round the net including the forums here. The Problem starts when after I sign in. When I open explorer I get the normal redirect to the sign in page. Once I sign in it's like the connection dies. I've seen a lot of suggestions that the server is picking up on a router on their network and blocks everything. I've tried mac addy clone, fixed IP, DMZ, NAT off, using the different connection types versus plain old Dynamic IP. The only thing I can tell you about the other routers people are using is they are a European version, you can tell by the plug that comes on them.
View 1 Replies View RelatedI am trying to stream movies and music to my Panasonic TV. I have a USB hard drive connected to the EA4500.
The TV sees the media on the device and music plays fine. However, every movie I've tried shows up with an exclamation point and when I try to play it I get a message to the effect that "unable to open media". Is the EA4500 media server only compatible with certain movies?
I recently upgraded my Wild blue internet service to the "Exede" system. When I kept losing the connection to my Mac Air book, the Wild blue service tech suggested that my wireless router (Linksys Wireless G 2.4 GHz router) was not robust enough to handle the increased "speed". They recommended I purchase a new router so I purchased the Linksys EA4500.
Now, after three weeks, the Linksys EA4500 router has stopped working. I am able to hook one of our Mac Books directly to the satellite modem to access the internet through an Ethernet connection. Finally, I finally reconnected my old Linksys Wireless G router to the modem to check to see if it would work and it does.
So, I'm wondering about the failure rate of the new Linksys EA4500 routers? Is there anything else I might try to get my new router to work??? I have unplugged it for an hour and then re connected it. I have pushed the reset button..My wireless indicator on the Mac Book Air shows full signal strength, but I can't connect to the internet with my new (less than 3 weeks old) router.
I have a problem with a wireless adaptor on a Toshiba Tecra (A11-1EE - PTSE0E-065052EN) running Windows 7.The wireless adaptor works fine but every now and again it will just stop working. The operating system says that the adaptor is turned off but it isn't. I've checked the driver but it is up to date.I have to disable the driver and then enable it again and then the adaptor begins to work correctly again.
View 4 Replies View RelatedI've just bought a linksys E3200 wireless router and it hasnt performed even alittle up to expectations.. As above stated, the router keeps disconnecting me from the internet and i do not know how to fix it. It gets really annoying especially when i have to use the internet to do work.
View 9 Replies View RelatedMy Linksys Router WRT54G has recently (yesterday) started dropping the internet after being online for a few hours.The current setup has been in place for several years. I started with the Broadband provider and they verified that the signal and cable modem is working properly. My own tests back this up. At first I simply reset the router. Unplugged it for 30 seconds and plugged it back in. Internet is back. Then I tried resetting the cable modem and the router. This works as well but the problem presists. Resetting the router alone has the same affect.So, something with the router is causing it to drop the internet. The network does not drop however. I can still use my network drive and the computers indicate a network with no internet connection.
View 2 Replies View RelatedI've been having issues with my e2500 router. I've found my connection dropping occasionally both with a wired connection and wirelessly on other computer. My desktop is connected directly to the router via ethernet and I've been keeping an eye on my network preference pane. Every 10 minutes or so the connection will be lost and computer says the cable is unplugged. It then resolves after 2 minutes.
I'm running OSX 10.8, firmware 1.0.07. Done a factory reset, power cycles etc. Configured with Cisco connect and manually multiple times. I've swapped out ethernet cables just to be sure it wasn't a cable issue.
Internet is fine when I've got the computer hooked up directly to the modem. No connection issues.
E4200 Version 2.0.37.131047 disconnects my wireless clients intermittently. I am seeing it mostly on the 5Ghz band but that is where most of my clients are connected. I have all the setting in advanced tweaked per cisco best practice. It just seems to reset every so often. Wired connection is not disconnected.
View 9 Replies View RelatedI have been having problems with my Internet the past couple weeks. If I am watching a video, it doesn't matter which site, the video will stop and start from the beginning or the video will just stop altogether and I have to refresh the page. Another problem that happens while browsing, it will take about a minute for a page to load. The computer I am using is wired right into the router.
The rest of the family's computers the apple tv and the roku are wireless. I have been hearing complaints from them and have witnessed the laggyness. While streaming videos on the roku or apple tv, the video will stop and say video is not available or no connection. This is what I get from ipconfig/all
Microsoft Windows [Version 6.2.8400]
(c) 2012 Microsoft Corporation. All rights reserved.
C:WINDOWSsystem32>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Matt-PC[code]......
I've looked all over the internet for this and can't find a definate answer. Waited for live chat and got kicked before I got to talk to someone... Just sold my computer and the plan was to buy a newer mac but we've been getting along fine without a computer with just using our iphones. So my question, I see that Cisco has the Connect Express app for the iphone, and I've read about all the features it has like changing settings, router features, etc. But I can't find anything on using the app for the initial set up of the router. I'm currently on an older linksys router (set up before we sold the computer) but it's time for a needed upgrade.
View 3 Replies View RelatedI got my ea4500 all set up. never had a media servor or anything like that, figured this would be an easier way. when i hook up my exteral i can find it but i can only view the files in windows media player. how can i just browse the folders manually? WMP doesnt let me browse the folders as they actually are on the HDD which is such a pain in the **bleep**.
shows a device in "network infrastructure" but it says problem sending command to the program when i click that. i dont want to have to view the HDD in WMP as a media device...
My new EA4500 (fw ver 2.0.36) won't obtain an IP from a Brighthouse TM502G cable modem. The EA4500 replaced a functioning WRT54G which would obtain an IP from the ISP. I've tried upgrading firmware and have used both straight-through and crossover cables between the EA4500 & TM502G to no avail. The EA4500 would issue IPs to it's clients, but not obtain one from it's TM502G. At the moment, all 3 are daisy-chained together with the old WRT54G in the middle in order to make the EA4500 work. Both WiFi and LAN ports function in this configuration.
View 1 Replies View RelatedI downloaded and installed inSSider for Windows and, under the 2.4 Ghz tab, I can clearly see the Router SSID, on Channel 6, exactly as configuredbin the Router. However on the 5 Ghz tab, nothing? I can see Channels 36, 40, 44, 48, 52 and so on BUT no trace of any wireless signal here?I carefully reviewed the wireless settings options and it is indeed enabled.
View 1 Replies View RelatedConnect my primary router EA4500 to another EA4500?
I tried and followed the steps provided here but it doesn't work at all for the Xth time already.
The first router installed and ran flawlessly in minutes. The second one has failed to work in bridge mode for 3 hours now.
Can we get a forum title just for the EA4500?
View 1 Replies View RelatedIn my apartment, I can receive the wireless signal of free scholl wireless, which is accessable without user name and password. Although the signal is not good, but we used to use a router EA3000 to relay the signal. Now my roommate is leaving with this this router. So I bought EA4500 and try to do the similar job. However, I find that the configurations on 192.168.1.1 are different between EA3000 and EA4500. Many options cannot be found in the EA4500 page, such as the wireless client.
View 4 Replies View RelatedI recently got an EA4500 from a friend and when I tried to run the Cisco Connect CD on my MacBook it gets to 25% and then stops and says it can't find a router. I've reset, powercycled, unplugged, plugged, searched, and searched but I cant seem to get it to find the router.
View 3 Replies View RelatedI'm hoping to get this router to allow WOL (actually wake on WAN) but it seems to be blocking the necessary broadcast magic packet even though the settings appear correct. It's not critical, but the reason is this: I'd like to shut down the home PC, but when necessary be able to start it up and use a VPN to access any info I need remotely.
From within the LAN, I can verity that WOL works. I have NIC and PCI WOL enabled in the BIOS. The NIC (a Marvel Yukon Gigabit) has WOL enabled as well as "allow this device to wake.." using magic packets under power management. The target machine's local IP is reserved through the EA4500 DHCP Reservation table. Just for troubleshooting, I opened port 9 in windows firewall. More importantly, I have ports 7-9 forwarded to my target LAN address. Single port forwarding... it just has been less reliable (?). I'm using a mask of 255.255.255.128 in order to enable broadcasting on .127 at some point as it seems it must be necessary. Broadcasting on .255 is not possible, despite some workarounds I found on the web. EA4500 firmware is the latest, 2.0.37. I have turned off the multicast filter and the anonymous internet filters under the security tab.
So, with these settings, I can WOL from inside the network no problem either targeting the LAN address, or by using a dyndns address. So far so good.With these same settings, I can go to WAN using Depicus or the Cloud Connect Pro app over 4G on an iPad. With all these same settings, WOLsniffer confirms the magic packet still getting through over WAN (obviously using the dyndns address). Even better, I can shutdown the target PC and STILL wake it up within a few minutes from WAN. Let me restate that! Wake up over WAN works, but only for the first few minutes after a shutdown.
However, if I wait 20 minutes or so, WOL stops working. If I change the port forwarding to .127, not only does it not work, but WOLsniffer will fail to see the magic packet. My conclusion is that the ARP table is getting purged, which is undertandable, and so the target LAN address isn't in memory. However, frustratingly the EA4500 will not broadcast no matter what settings you use. This limitation is undocumented, and counterintuitive since the software allows you to disable multicast filtering and does not notify you of an error when forwarding to xxx.xxx.xxx.127 with a 255.255.255.128 mask.
How do I enable WDS on my new EA4500 ?
View 3 Replies View RelatedWas thinking to buy this router but I am not sure if it supports magic packets in order to use wake on lan on PCss and NAS
View 3 Replies View Related