I downloaded and installed inSSider for Windows and, under the 2.4 Ghz tab, I can clearly see the Router SSID, on Channel 6, exactly as configuredbin the Router. However on the 5 Ghz tab, nothing? I can see Channels 36, 40, 44, 48, 52 and so on BUT no trace of any wireless signal here?I carefully reviewed the wireless settings options and it is indeed enabled.
View 1 RepliesI am trying to figure out what channel my Linksys E4200 is CURRENTLY using (at the time I check it)I am having issues with occassionally losing my connection (mostly from the computer furthest from the router) and it may be caused by a cordless phone , in the room with that computer as I think the problem only occurs when on the phone in that room.So I am trying to determine what channel that it may be using at the time of the drops ...(so I can set it NOT to use that channel)I'm pretty sure it it something on the 5ghz (40mhz)side .but I don't really want to set the router to use 20mhz only as the speed greatly drops when on 20mhz only (i.e. 50mbps vs up to 200mbs when 5ghz is activated)
Checking my Router set up page, I see only what channels is CAN use, not what is currently being used.Is there anyway to identify what channel it is currently using so I can see if it is a specific channel causing the issue and not have to switch off 40mhz?
How do I change the channel on my Linksys WRT54G2 ROUTER?
View 3 Replies View RelatedAny success with a recent vintage Macbook Pro connecting to the 5.8Ghz channel on a WRT610N. I can connect with the 2.4 channel without a problem but I cannot maintain a connection on the high channel. Linksys support told me that the hardware was not compatible with the high channel.
View 3 Replies View RelatedEA6500 5GHz band only four channels (36,40,44,48), the lack of 149,153,157,161 channel, firmware Ver.1.1.28.146072, how to add 149,153,157,161 channels?
View 3 Replies View RelatedMy E3000 has about 60% packet loss if the channel selected is anything other than 1. I can't enable 5GHz or even 40mhz 2.4GHz channels without dropping 60% packets.
View 9 Replies View RelatedI am working with a WRT320N for some weeks now, but I don't get the fact that 40Mhz channel width is only allowed for Automatic channel selection.I keep losing connection and the channel keeps changing.I want an option to change the channel manually (like in every good WLAN router!!), also with N data rate (40Mhz channel width).I know how to select the best channel, so why aren't I able to change it the way I like it?
View 4 Replies View RelatedE4200 2.4 channel extremely slow.
View 7 Replies View RelatedChannel 1 & 2 Signal Collapse. Just recently purchased the E3200.
When I set the 2.4GHz band to Channel 1 or 2, the signal is unstable. According to WiFi Analyzer, the signal keeps appearing and disappearing every couple seconds.
But my neighbor's router that's on channel 1 or 2 remains stable, so it's not a problem with WiFi Analyzer.
Firmware: 1.0.04
What's the point for two options, auto or 20 mhz only? there is no third option so if you choose auto its still 20 mhz am i right?BTW i had to change channel width to 20 mhz only because under auto the speed was horrible.
View 3 Replies View RelatedEA6500 5GHz band only four channels (36,40,44,48), the lack of 149,153,157,161 channel, firmware Ver.1.1.28.146072,how to add 149,153,157,161 channels.
View 3 Replies View Relatedi can only connect to my router at 144mbps(wireless N) every so often i notice my router will channel bond to 11+7, and i can connect at 300mbps!(lasts like 5 minutes) then just randomly dies and will only reconnect at 144mbps. Its not a wireless card problem since my old netgear 3700 died on me it connected up just fine at 300mbps.i use inSSIDer and i can verify that it only connects using 1 channel(i've set to auto) and tried setting to each individual channel.
View 1 Replies View RelatedI've recently purchased the E2500, done the setup but am facing some issues.I'm unable to see the 5GHz channel SSID, I can only see the 2.4GHz channel SSID.Have tested all the laptops and devices at home and all can't see the 5GHz channel.The list of devices are:
a) iPhone 3GS
b) iPhone 4G
c) iPhone 4GS (some sites says it doesn't support, some says it does, I'm confused as a result)
d) Samsung laptop
e) Dell laptop
f) Momo11 Little Bird Edition tablet (Made in China [MIC])
g) No name MIC tablet
Secondly, is there any tips / tricks to tweak the modem to increase the internet speed?
My desktop pc has an Asus PCE-AC 66 PCI card (supports up to 1300 mbps wifi) and is only 5m or so away from the the EA6500 router without any obstructions - yet i cannot connect at 1300 mbps AC wifi. On the EA6500 router, i have selected 'mixed' as network mode under 5ghz (since i have some other devices which connect on wifi N on 5ghz) but if i select channel width as 80mhz, i have issues connecting to the 5ghz network on the desktop pc. The desktop briefly connects and under status it says lan speed as 1.3gbps but then it disconnects and i can't connect again. If i select channel width as 'auto' then no problems, the desktop can connect but lan speeds are only 400-600 mbps. why i cannot connect at 1300 mbps?
View 6 Replies View RelatedI just purchased a Linksys Cisco E900 router and hooked it up to my Internet cable. The Internet service that my ISP is giving me is PPPoE, fiber link (100 Mbps).
I did the set up. I connected my computer (via Ethernet cable) and my laptop (via wireless) to the router.
Now... there are other wireless networks around me. The WI-Fi channel my router fixed to is 1, apparently - saw it from the settings. But I can't find a menu anywhere in the router's gateway (192.168.1.1) from where I can change the wireless channel, wireless bandwidth etc.
I have an E3000 Dual Band. On my 5Ghz channel, I can select Auto(DFS) or I can manually select a channel.First of all, what does the DFS stand for? My 2.4 GhZ channel only has Auto, not Auto(DFS).
Second, when I select Auto(DFS), my wireless speed defaults to 144Mbps, and is only a single channel (I can see it in the in SSIDer utility). When I manually select a channel, no matter what channel it is, I get 300mbps and I can see that the signal is two channels (for instance, 36+40). Why Auto(DFS) doesn't automatically select the best channel and fastest speed?
I have a Linksys WRT54GL version 1.1. The firmware is 4.30.11 (European version).In the Basic Wireless Settings I can't change the Wireless Channel. It remains at channel 1, and I simply can't alter it.This is strange, because in earlier firmware versions, I was able to change the channel without any problems at all. I would like to continue to use this firmware version. How can I solve this problem?
View 9 Replies View RelatedI've looked all over the internet for this and can't find a definate answer. Waited for live chat and got kicked before I got to talk to someone... Just sold my computer and the plan was to buy a newer mac but we've been getting along fine without a computer with just using our iphones. So my question, I see that Cisco has the Connect Express app for the iphone, and I've read about all the features it has like changing settings, router features, etc. But I can't find anything on using the app for the initial set up of the router. I'm currently on an older linksys router (set up before we sold the computer) but it's time for a needed upgrade.
View 3 Replies View RelatedI got my ea4500 all set up. never had a media servor or anything like that, figured this would be an easier way. when i hook up my exteral i can find it but i can only view the files in windows media player. how can i just browse the folders manually? WMP doesnt let me browse the folders as they actually are on the HDD which is such a pain in the **bleep**.
shows a device in "network infrastructure" but it says problem sending command to the program when i click that. i dont want to have to view the HDD in WMP as a media device...
My new EA4500 (fw ver 2.0.36) won't obtain an IP from a Brighthouse TM502G cable modem. The EA4500 replaced a functioning WRT54G which would obtain an IP from the ISP. I've tried upgrading firmware and have used both straight-through and crossover cables between the EA4500 & TM502G to no avail. The EA4500 would issue IPs to it's clients, but not obtain one from it's TM502G. At the moment, all 3 are daisy-chained together with the old WRT54G in the middle in order to make the EA4500 work. Both WiFi and LAN ports function in this configuration.
View 1 Replies View RelatedConnect my primary router EA4500 to another EA4500?
I tried and followed the steps provided here but it doesn't work at all for the Xth time already.
The first router installed and ran flawlessly in minutes. The second one has failed to work in bridge mode for 3 hours now.
Can we get a forum title just for the EA4500?
View 1 Replies View RelatedIn my apartment, I can receive the wireless signal of free scholl wireless, which is accessable without user name and password. Although the signal is not good, but we used to use a router EA3000 to relay the signal. Now my roommate is leaving with this this router. So I bought EA4500 and try to do the similar job. However, I find that the configurations on 192.168.1.1 are different between EA3000 and EA4500. Many options cannot be found in the EA4500 page, such as the wireless client.
View 4 Replies View RelatedI recently got an EA4500 from a friend and when I tried to run the Cisco Connect CD on my MacBook it gets to 25% and then stops and says it can't find a router. I've reset, powercycled, unplugged, plugged, searched, and searched but I cant seem to get it to find the router.
View 3 Replies View RelatedI'm hoping to get this router to allow WOL (actually wake on WAN) but it seems to be blocking the necessary broadcast magic packet even though the settings appear correct. It's not critical, but the reason is this: I'd like to shut down the home PC, but when necessary be able to start it up and use a VPN to access any info I need remotely.
From within the LAN, I can verity that WOL works. I have NIC and PCI WOL enabled in the BIOS. The NIC (a Marvel Yukon Gigabit) has WOL enabled as well as "allow this device to wake.." using magic packets under power management. The target machine's local IP is reserved through the EA4500 DHCP Reservation table. Just for troubleshooting, I opened port 9 in windows firewall. More importantly, I have ports 7-9 forwarded to my target LAN address. Single port forwarding... it just has been less reliable (?). I'm using a mask of 255.255.255.128 in order to enable broadcasting on .127 at some point as it seems it must be necessary. Broadcasting on .255 is not possible, despite some workarounds I found on the web. EA4500 firmware is the latest, 2.0.37. I have turned off the multicast filter and the anonymous internet filters under the security tab.
So, with these settings, I can WOL from inside the network no problem either targeting the LAN address, or by using a dyndns address. So far so good.With these same settings, I can go to WAN using Depicus or the Cloud Connect Pro app over 4G on an iPad. With all these same settings, WOLsniffer confirms the magic packet still getting through over WAN (obviously using the dyndns address). Even better, I can shutdown the target PC and STILL wake it up within a few minutes from WAN. Let me restate that! Wake up over WAN works, but only for the first few minutes after a shutdown.
However, if I wait 20 minutes or so, WOL stops working. If I change the port forwarding to .127, not only does it not work, but WOLsniffer will fail to see the magic packet. My conclusion is that the ARP table is getting purged, which is undertandable, and so the target LAN address isn't in memory. However, frustratingly the EA4500 will not broadcast no matter what settings you use. This limitation is undocumented, and counterintuitive since the software allows you to disable multicast filtering and does not notify you of an error when forwarding to xxx.xxx.xxx.127 with a 255.255.255.128 mask.
How do I enable WDS on my new EA4500 ?
View 3 Replies View RelatedWas thinking to buy this router but I am not sure if it supports magic packets in order to use wake on lan on PCss and NAS
View 3 Replies View RelatedI really want to have a password on my wifi, but I cant control it when all it keeps asking me is for a CD I have a EA4500
View 1 Replies View RelatedUsing the FTP server built into the EA4500 firmware. I can get the FTP service to work from some computers outside my home network, but when i try to access the service from a PC within my home network i am unable to connect to the server through the WAN address.
View 1 Replies View RelatedI bought 2 weeks ago a Linksys EA4500 after searching the best Wi-Fi Router all over the net... I choose this cos all over people writed that it was amazing, fast a nd very good coverage all over the house.
Before I had a Buffalo AirStation Dual Band, wich worked perfectly. But since I have several tv and a central NAS whit all films in MKV, I wanted the BEST product for my system, so I choosed Linksys EA4500!
Well, the result is that (when it works it is greate) but sometimes it disconnects and I have to restart it... And second thing that makes me MAD is that the coverage in my house is WORST!! Before my Wi-Fi was present in all the house, now in some parts doesn't work! The position is the exact same of the Buffalo, so it's not a problem of position... I tryed also a router of 40€ and it has a better coverage! How come? how is it possible that a person pays more than 200$ (in Italy it costs 185€) and the result is so BAD??? I'm totaly freak about Linksys now.
I'm in the process of wanting to upgrade my wireless network but I'm not really agreeing to the Cloud Connect, I don't need to have my settings on the internet. I want to manage everything on my own. I've found the following link on the community to be able to put the classic firmware before the cloud connect feature {URL}.
My question now is : If I buy a brand new EA4500, will it still be possible to downgrade to that firmware? No problem with this one? I'm hoping Cisco will continue to publish bug fixing if any to this classic firmware.
I purchased a EA4500 and at first I could connect to it through its default ciscoxxxxx ssid on my laptop which is 2.4GHz only. I upgraded the firmware using the PC utility and now I can't find the 2.4GHz SSID no matter what settings I do. I've disabled and enabled it multiple times, changed it to have no security or with security and enabled and disabled it and renabled it. Nothing seems to work, but for some reason the 5GHz side I can connect to using a 5GHz device. I've also tried disabling the 5GHz side, but still no 2.4GHz.
View 4 Replies View RelatedJust purchased a ea4500 router. Have setup multiple computers/devices already and works great. This computer (HP dv6000 running Win Vista home prem) however will not connect to the internet. It states that it is connected to the router (computer sees router), using the cloud connect app on my iphone i can see this computer, but will not allow access to the internet (local connection only). It works fine with the wired connection. When attempting to use the cloud connect software, it says it was unable to complete the install. Have attempted trying while connected by wire as well, same result. Have deleted the wireless connection and allowed software to find connection, still same result, cannot install. Wireless worked perfectly with previous router (WRT54G) three days ago.
View 6 Replies View Related