I'm using an RFC 1483 Bridged adsl connection on a WAG54GS router. Downstream rate says 2043 Kbps, and upstream rate only 35 Kbps. In the router setup page I have not found any place to change downstream/upstream rates. How can I increase \the upstream rate?
View 2 RepliesI have an RV042 router and I'm looking to monitor the total upstream and downstream traffic from within the router. I know there is tons of software that I can put on a netowrk computer to monitor traffic, but is there any software that I can put on the router itself that will monitor the traffic from within the router?
View 1 Replies View RelatedNetwork settings. What I want to do is limit the rate that people can download files from my webserver remotely. LAN connections should still be able to transfer at full speed, but anything outside of the local network should be limited to 200Kbps per connection. Is that even possible? Can I limit the number of connections per client (probably by IP)?
If this can't be done at the OS level, is there any way I could script it using PHP? Maybe read X bytes into a file and then sleep...
using task manager in XP it is clear that while browsing data is being uploaded mirroring the data downloaded..ie in a given period if 18mB comes downstream (just surfing) then 11mB goes upstream. The graph in task manager shows that the peaks and troughs of the data upstream and downstream exactly correspond and watching the bytes tick over confirms that data goes out for every data coming in.I assume that this should not happen? I realise ip protocols have some kind of error detection that may require uploading data, but the amount sent seems excessive! From my limited understanding of networking and running wireshark it looks like that when packets come from an ip on the web ( i use the terms web/internet interchangeably ) then packets are sent out to the same ip ... using TCP and HTTP ( I don't really understand them ). The info for one such packet going out is "Continuation or non-HTTP traffic" using the HTTP protocol, which sounds a bit contradictory. I regularly run virus scans and rarely find anything. The cpu regularly maxes out and its usually something to do with firefox ( I've heard of buffer overflows but i assume the problem is a relatively old processor and hardware).The browser is firefox. OS is XP.Coincidentally, the pc was recently rebooting after crashing until I disabled "restart on system failure" which prevented the crashes ( if they were crashes and not just the system reacting to an error ). Again, that is a bit suspicious but maybe not. Spybot, bit defender quickscan,avira, zone alarm, malwarebytes etc haven't flagged anything up.Maybe the router is not configured properly. As with all these things, there will be some simpler things to start with to diagnose this issue (if there is one ) but I don't know what they are.The pc uses wifi to connect. The isp is not the best and the speed is pretty bad for adsl. Every couple of days the router needs rebooting because it stops giving out ip's.
View 6 Replies View RelatedMy router refuses to link to the internet. Status indicates Interface: Down. I thought this was probably a firmware upgrade issue but can only find v1.01.03 which is already installed. Linksys website has no firmware listed for download.
I have downloaded and re-installed the v1.01.03 .img file with no effect. Is this the latest firmware for this model?
The subject syas it all really, I've spent all evening trying to get this to work, firmware is now on 1.01.05 and still no luck. Maybe it just doesn't support it?
View 1 Replies View RelatedI have an old router linksys WAG54GS and now with my new internet connection gave me a HUAWEI 530.I'm still using linksys.So i wanted to connect the HUAWEI on the Linksys cause it has an external button for wireles, which Linksys doesnt.I followed the wizard you wrote.The DHCP off on the HUAWEI Different IP.So the Wired LAN worked fine, having an IP from the Linksys, but the wireless doesnt get one..I tried a lot of things on the huawei, nat off etc but nothing On the linksys i give on DHCP IPs from 192.168.1.105 - 7.I tried connect the netbook but only wired worked, not even my cellphone.
View 2 Replies View RelatedI'm using a WAG54GS 1.0 router with up to date firmware, and signal around the house has always been fine, yet today it has suddently dropped to a VERY limited range - I'm sat right next to it now on a laptop and the signal is 2/5 bars - "fair".I've reset factory settings yet to no avail, I can't even get signal in the next room!
View 1 Replies View RelatedI need to upgrade my WAG54GS, but there is no firmware in support. My latest firmware is V1.01.03. Where can I download it?
View 4 Replies View RelatedComparing my brand new linksys x3000 (Firmware Version:v1.0.03) with my old zyxel p660hw I see that the linksys is running a downstream noise margin of 8.2dB while the old zyxel is running a downstream noise margin of 15dB. Needless to say, I am very disappointed. why the linksys value should be so much lower?
View 5 Replies View Relatedi'm setting up a wireless network for a local B&B they currently have a Linksys WAG54GS ADSL router in one of the rooms but need the wireless signal to reach each guest room the house has thick brick walls and an upstairs.i was thinking of using 2 x repeaters, the WRE54G's, and to put one on the ground floor within range of the current ADSL router and to put another on the 1st floor within range of the repeater on the ground floor to receive the bounced signal.I don't know much about these repeaters and how they work exactly and so unsure if this would be a viable solution in my case.
View 6 Replies View RelatedWe are connected to 2 different providers (PROV01 and PROV02) with eBGP full internet tables. PROV01 routes have higher local preference over PROV02.
We are having problems with our provider and would like your expertise. PROV01, higher preference has been having trouble with their router. The BGP remains up but the router stops forwarding traffic. as a resulta we lose connection to the internet but our traffic never goes to PROV02 since PROV01 BGP remains up announcing the 400K routes to us.
Is there a way to test internet connection though PROV01 and as the "internet is DOWN" automatically change traffic to PROV02? Can BGP parameters changes be triggered by IP SLA? Our router is an ASR1006 RP2.
I am wondering if it is possible to Create a wireless bridge. I am trying to connect a linksys WAG54gs to next doors wireless router. It's ok she's my mother in law.
She has a BT home hub 3.
How do I turn off the SIP ALG?
View 1 Replies View RelatedI am having problems with my linksys wireless G ADSL gateway WAG54GS router. I am on Windows Vista/Internet Explorer. When I set up the router to work on the internet when I first bought it (several years ago), something must have gone wrong in the installation because it works only when connected to the computer by the lead, and NOT wirelessly.
While this is fine for general internet browsing etc on the main computer, my problem now is that I cannot connect anything else to it (such as my Playstation 3) because the router does not work wirelessly and I do not have the WPA key that the PS3 asks for. Is there any way can fix this without doing a complete reset on the router?
[ALSO: the router also periodically goes wrong, e.g. loses connection for no reason at all - I often have to disable and then enable the internet connection, or turn the router off for 15 seconds then switch it on again, and then it's fine again. I live in a rural area though, so it might be because of a poor connection. Our telephone connecton isn't very good either and sometimes goes wrong.]
How to change the frequency on X2000
View 1 Replies View RelatedPossible using a firmware upgrade to change the wag200g from annex B to annex A?T
View 6 Replies View RelatedThis is an interesting and don't know where to begin.From factory reset I connect a latop to 192.168.1.1 and change the IP address to my subnet 192.0.1.5/24. I disable DHCP too.THen i plug it in to my LAN and I can ping 192.0.1.5 but can't http to 192.0.1.5
So I remove from LAN, connect to my laptop, manually change my laptop op to 192.0.1.4/24 and then my laptop can http to the AG241 on Linksys AG241.Is there anything on the AG241 that could be confusing my LAN?
We have a linksys WAG54GS router the secure easy setup button of which was pressed instead of the on off switch when a reset was required. Now we can only browse the internet via a cable from the pc lan port to the router ethernet port. Things done :- Secure easy setup button held down for 10 seconds. Router went to an unsecured one now back to secure.
View 3 Replies View RelatedI am looking to replace my current WAG54GS Gateway with the EA6500. Problem is the new one does not have a built in ADSL2+ modem (I am in the UK and my ISP is Demon Internet). I therefore need to purchase a separate Modem to connect to the router.
View 9 Replies View RelatedI fought my ISP (frontier) for weeks trying to get their 7500 DSL/modem/router configured in bridge and working into the WRT600N. Finally gave up and put a new Engenius EVR100 behind the 7500 bridge and it came up fine in 10 mins. Now I would like to use my old WRT600N downstairs as a second router and run it in the range of the Engenius DHCP, with DHCP turned off in the WRT600N.
My question is this ... Do I set the WRT600N as a static IP address and use an address in the range issued by the EVR100?And, if so, what would the sub-net mask, default gateway and DNS numbers be? Also would the router address itself (lets say I use 192.168.0.120 from the EVR100 range) be different then the static IP address?
E4200 with an external hard drive WD My Book (1TB) connected to the router via USB.Desktop PC (Windows 7) connected to router via Ethernet cable.Laptop PC (Windows 7) connected to router via wireless connection.I wanted to create a central media (videos/pictures) file on the external hard drive connected to the router. However, the transfer rate is terribly slow. Interestingly, it is 50KB/second when copying from the Desktop (via Ethernet) and 1.6Mbps when copying from the Laptop via wireless.
View 9 Replies View RelatedI just recently bought a WAG160N and I have a big issue with it, I can't change the password for the default admin account. All I get is this error in the browser "Error 324 (net::ERR_EMPTY_RESPONSE)"
Quick reset.Power cable disconnect for 60 sec.Factory reset followed by a reset of the router for 60 sec.Clearing my browsers cookies and internet temporary files.Only things I have changed is the Basic Setup to get connected to my ISP and the Wireless settings.
Details about clients, firmware versions etc.
Windows 7 build 7601 Service Pack 1 Chrome Browser 16.0.912.75 Wireless-N ADSL2+ Modem Router V2 firmware version 2.00.20
How to reset my WRT120N Router, It was originally set up using a PC, I am now on a MAC but my husband has a PC Netbook. In our previous location, we were all able to access the internet without any trouble. I have tried going into the router various ways and have not been successful. One path was using the CD that came with the router
View 1 Replies View RelatedMy X2000 modem connect only with small speeds Kbps, it's very weak than Linksys WAG54GP2 MBPS. If I put laptop near the modem speed doesn't change.Only change occurs when I change the channel. But it speed down after a while.I set, N connection, security is WPA-personal, tried some different channel, connection 20-40mhz, update the firmware (there is no problem with laptop, with another modem I can connect with 150kb/s speed) And, if I choose auto setup, security change to WPA, If I'm not wrong.
View 3 Replies View RelatedHardware Software profile;
Laptop - Windows 7
Desktop - Vista Ultimate SP2
Router - Cisco Linksys E3200
Cables - CAT6
I am a sales engineer, so I use my desktop and laptop all the time. When on road, I sync my desktop with my laptop using a program called ViceVersa. This a very good, reliable syncing program that I have been using for over 10 years ( with upgrades ).
The program allows me to sync my desktop and laptop. The program also shows the data transfer rate during the syncing process. The typical data transfer speed is between 5MB/s and 10MB/s with sometimes up to 12MB/s. A typical sync between the computers will take about 3 - 5 minutes at the ~ 10 MB/s transfer rate using ethernet CAT6 cable inteface. At about 11pm last Tuesday,there was a Windows update on both my Vist and Win7 computers. On wednesday, I went to do a typical sync. The system has dramatically slowed to 59KB/s max. This is about 150 times slower than 5-10MB/s that I was used to for so many years. My typical sync was now taking about 2 hours....unacceptable ! I have tried everything to figure out what is going on and how to fix it but nothing has worked.
Then I tried to see what would happen if I disconnected my ethernet cable ( between the router and the laptop only ) and just sync using the wireless network. With that configuration, the transfer rate is ~ 2.5 MB/s which is not great but is much, much better than 59KB/s. I actually do not know what a reasonable wireless transfer rate should be since I never really did it before due to the faster speed of the wired configuration.
This is just a LAN. Only connecting my Desktop to my Laptop via the Cisco router.
How I can get my wired configuration back up to the 5-10MB/s transfer rate that it once was?
Yesterday, I changed my old belkin n1 router with Linksys WRT54GL router. Ever since them my upstream speed is really slow. I did the speedtest its like .5mbit. My downstream speed is just fine. This issue is only on wired computers, upstream speed on wireless computers is just fine.I retested router & modem several times, my upstream speed is normal when I connect cable directly from modem to my computer.Current Firmware Version is 4.30.14 build 5.
View 1 Replies View Relatedwe finally got my Cisco refurbished E2500 configured and working downstream from a UVerse 3801HGV box. We had to change the default IP address of the 3801 because it conflicted with the E2500's default. The E2500 is set up to get its Internet IP address using DHCP from the 3801. This is working fine for normal web browsing, etc. However, anything that requires extended connections (downloads, streaming, etc) freezes after a couple of minutes, forcing me to refresh the action to get it started again. Extremely annoying to say the least.
I'm pretty sure that I've tracked it down to the E2500's configuration of the 3801's DHCP allocation. For some reason, the E2500 wants to set the DHCP Lease Time for the 3801's assigned IP address to 10 minutes regardless of the upstream settings from the 3801. The 3801's default is 24 Hours which I've changed to 168Hours (7 days), but the E2500 stays stuck at 10 Minutes. Specifically, I'm referring to the setting displayed on the E2500 under Status>Router>Internet Connection IPV4>DHCP Lease Time.
here is my setup:
Router: DIR-655 B1 2.00NA
Desktop1: DWA-160 A1 1.80 [IP: x.x.x.104]
Desktop2: DWA-160 A1 1.80 [IP: x.x.x.103]
Laptop: Intel WiFi 5300 AGN [IP: x.x.x.100]
iPad 2 (1): [IP: x.x.x.101]
iPad 2 (2):
Router Config, Status, and Inssider Report:
[URL]
I want to determine if i completely understand the meaning of forwarding rates on a switch. From my understanding, if The port density on my switch is 48, each at a 1G speed i have a total of 48Gbs. however, if a switch, for example the 2960 has a forwarding rate is 40Gbs, I take it to mean that i cannot get 48Gbs of through put but only 40Gbs,is this correct ?
View 3 Replies View RelatedI am using an old Asus netbook as a file server in home network which I connect through Ipad over ftp. It works for the most of daily tasks fine though but the connection is with rates under 1 Mbps still slow for data intensive tasks. My question is: if I buy a new hard drive with wireless access capability could I hope for significantly better transfer rates? If not, then I can't see any point why someone would buy this devices which in some cases can only be accessed over the network. what is wrong with my configuration that I get significantly slower rates? I run SuSE Linux on the netbook, the ftp deamon is vsftp and have a 54 Mbps wireless router which I think can still be considered standard. Is there anything I can do to increase the ftp transfer rates? I think it should be possible since even downloads over http on the same machine often exceed it.
View 2 Replies View Relatedim experiencing very slow transfer rates averaging 600 kb/s when transfering files. my PC has a compatible dwa-552 card and both the router and card have latest drivers / firmware. i have various changes on the router and to no avail. all devices PC / laptops running N @ 20 mhz / channel 11. i can see 2 other networks but very low signal using diff channels.what setting might i be overlooking in the router that might cause this slow trans rate? incidentally, when i transfer .jpg or .pdf files the transfer improves to 2.5 mb/s. however, when i transfer a folder containing subfolders with diff file types the trans rate drops sharply to 600 kb/s.
View 14 Replies View RelatedWe use a couple of 2910al ProCurves for our core switching/routing then we have a few 2626 access switches.
Despite allocating adequate ports in our new building, I'm still having a problem with users plugging in shitty little D-Link 5 port hubs at there desk.
I'm guessing I'm going to have to only allow the mac's of approved workstations? Which sounds like a management nightmare.