The subject syas it all really, I've spent all evening trying to get this to work, firmware is now on 1.01.05 and still no luck. Maybe it just doesn't support it?
View 1 Replies
I am wondering if it is possible to Create a wireless bridge. I am trying to connect a linksys WAG54gs to next doors wireless router. It's ok she's my mother in law.
She has a BT home hub 3.
i'm setting up a wireless network for a local B&B they currently have a Linksys WAG54GS ADSL router in one of the rooms but need the wireless signal to reach each guest room the house has thick brick walls and an upstairs.i was thinking of using 2 x repeaters, the WRE54G's, and to put one on the ground floor within range of the current ADSL router and to put another on the 1st floor within range of the repeater on the ground floor to receive the bounced signal.I don't know much about these repeaters and how they work exactly and so unsure if this would be a viable solution in my case.
View 6 Replies View RelatedMy router refuses to link to the internet. Status indicates Interface: Down. I thought this was probably a firmware upgrade issue but can only find v1.01.03 which is already installed. Linksys website has no firmware listed for download.
I have downloaded and re-installed the v1.01.03 .img file with no effect. Is this the latest firmware for this model?
I have an old router linksys WAG54GS and now with my new internet connection gave me a HUAWEI 530.I'm still using linksys.So i wanted to connect the HUAWEI on the Linksys cause it has an external button for wireles, which Linksys doesnt.I followed the wizard you wrote.The DHCP off on the HUAWEI Different IP.So the Wired LAN worked fine, having an IP from the Linksys, but the wireless doesnt get one..I tried a lot of things on the huawei, nat off etc but nothing On the linksys i give on DHCP IPs from 192.168.1.105 - 7.I tried connect the netbook but only wired worked, not even my cellphone.
View 2 Replies View RelatedI'm using a WAG54GS 1.0 router with up to date firmware, and signal around the house has always been fine, yet today it has suddently dropped to a VERY limited range - I'm sat right next to it now on a laptop and the signal is 2/5 bars - "fair".I've reset factory settings yet to no avail, I can't even get signal in the next room!
View 1 Replies View RelatedI need to upgrade my WAG54GS, but there is no firmware in support. My latest firmware is V1.01.03. Where can I download it?
View 4 Replies View RelatedI'm using an RFC 1483 Bridged adsl connection on a WAG54GS router. Downstream rate says 2043 Kbps, and upstream rate only 35 Kbps. In the router setup page I have not found any place to change downstream/upstream rates. How can I increase \the upstream rate?
View 2 Replies View RelatedOur family has about three computers that use a wireless network that we all share. We have an old Gateway, a WCG200, that is bridged to an E2000, which was set-up ever since we required better security when someone used our connection to illegally obtain movies. We got a letter which warned us of any future violations that could cause legal action, so we looked into our wireless connection to better secure it from any other individuals outside of our household. The WCG200 is connected to the outlet in the wall via cable, and then connects from the Ethernet to the E2000. The E2000 has a stronger security setup than the WCG200, which is the advice we received from our ISP and would allow us to keep the Gateway. It provides a strong signal, but from time to time, we suffer latency or slow loading through all of our online devices, even though our connection speed displays a solid 72.0 Mbps. I've tried the Event Viewer to see any problems, and I have noticed some small things:
- WLAN AutoConfig service has successfully stopped.Wirel?
- WLAN Extensibility Module has stopped. Module Path: C:WindowsSystem32cmihvsrv64.dll
- The server {E10F6C3A-F1AE-4ADC-AA9D-2FE65525666E} did not register with DCOM within the required timeout.
- Broadcom NetLink (TM) Gigabit Ethernet: The network link is down. Check to make sure the network cable is properly connected. [This last one is strange, since I use the Wireless Network Connection with a DW1501 Wireless-N WLAN Half-Mini Card, while the Broadcom adapter is under the Local Area Connection and displayed as not connected.]
Other than that, I'm not quite sure what the recurring problem comes from. Our WCG200 has a firewall enabled and our E2000 has an SPI firewall enabled. The security mode of the E2000 is a WPA2 setup. We have disabled the wireless network of our WCG200 in order to make use of the E2000.
The latest firmware seems to support bridge mode. Does it mean the router can connect to another router wirelessly in the bridge mode?
View 6 Replies View RelatedI tried to set my WAG200G as a wireless bridge, but I encountered some problems doing so.
First I reseted the router to factory default settings, then I put it in "bridge mode only" disabled DHCP and UPnP (this was required for the college network I want to use on it to work). Then I put the UTP cable in one of the LAN ports.
When I try to acces this network though a wire everything works fine, I can see the other devices connected to the network and I can acces the internet. When I try to use the network wirelessly, I still see the other devices on the network but I can't connect to the internet. (The acces to the internet is gained by logging in inside the browser, like with wifi hotspots)
I have a small home network using a Linksys WAG320N which acts as the modem (to connect to BT using PPPoA for ADSL) and provides 4 wired 100Mbs network connections along with a wireless N connections. I use WPA2 (personal) to secure the network and have a white list for allowed wireless devices. Everything works fine.In another part of the house (where I can get a good wireless signal) we have the main TV in the house. Here I have a SKY HD box and a small media player. What I would like to do is connect these two devices to the network and running a network cable is not practical, so I thought I would setup a wireless bridge.I tried a TP-Link bridge borrowed from a friend by this failed to work. I now know this to be because the WAG320N does not support WDS.Will a Linksys WES610N connect to my WAG320N to provide me with what I want?
View 1 Replies View RelatedHow do I turn off the SIP ALG?
View 1 Replies View RelatedWe have a linksys WAG54GS router the secure easy setup button of which was pressed instead of the on off switch when a reset was required. Now we can only browse the internet via a cable from the pc lan port to the router ethernet port. Things done :- Secure easy setup button held down for 10 seconds. Router went to an unsecured one now back to secure.
View 3 Replies View RelatedI am looking to replace my current WAG54GS Gateway with the EA6500. Problem is the new one does not have a built in ADSL2+ modem (I am in the UK and my ISP is Demon Internet). I therefore need to purchase a separate Modem to connect to the router.
View 9 Replies View RelatedI need to configure a WAG 120 N as a bridge, so I can have my public IP as an output of an Ethernet port. I need this configuration because I have a non ADSL router managing VPNs and needs the public IP on the WAN port of this router.
View 3 Replies View RelatedI have a WAG120N. I wish to use it as a modem only and not as a wireless router.I have another wireless router I want to use to handle network connectivity.I want the wag to be set to 10.10.1.1 and I want my router on 10.10.1.2What bridge mode do I set on my wag? Do I need a crossover cable?
View 1 Replies View RelatedI'v just changed my internet provider. That new one uses Annex b, my wag160n is purposed to annex a. Thats what i'v done. Turn on bridge mode turn off dhcp, set PPPoE with my login and password. And here is my problem. I cant connect by wifi with more then 1 device. I can only connect with my laptop when i'm trying to connect on my xbox it says it cannot get ip adress from router. What shoudl i change ?
View 6 Replies View RelatedI have an ADSL Modem WAG200G Annex A, with latest firmware. I recently purchased a Linksys E2000 to upgrade my wireless to N, plus to get 4 gigabit Ethernet Ports for my NAS.
The problem is, I set WAG200G to "Bridge mode only", and from within E2000, I provided PPPoE credentials (user name and password), it does not work, no Internet connection!
Normally, with the WAG200G, PPPoE credential is set as followings (and it works)
Type: PPPoE Multiplexing: LLC Virtual Circuit: "0" for VPI (0~255) and "33" for VCI (0~65535) "Keep Alive" option
on E2000 Router, PPPoE does not have the above option for me to select. Only User Name and Password field
Is it possile make a bridge with my WAG54G2 and another Access Point ?
View 1 Replies View Relateddifferent ways to connect a printer to the X3000. how to connect a printer to the X3000, i.e. wirelessly, USB port, or directly via one of the LAN ports. I also checked the product information for X3000 on the CISCO website and it only makes reference of the USB port as StorageLink.
. Since then I have reconsidered and now am looking to purchase the E4200V2 to connect in bridge mode to my X3000 instead of the E1500. Correct me if I am wrong but connecting the E4200V2 to my X3000 should be the same connecting the E1500 to my X3000, i.e. bridge mode? Yes or No?And my final set of questions is rregarding what would be the best set-up for adding a storage device and printer to my network once I get the E4200V2 and set it up in bridge mode?
- Should I connect both the printer and storage device to my the E4200V2?
- Should I connect them both to my X3000, which provides my internet connection?
- Should I connect one to the X3000 and one to the E4200, if so which to which for best set-up?
I'm trying to configure my WAG200G to work in bridge mode so that it can transfer my external IP address to my ISA server.My network map is very simple,Internet -- WAG200G -- ISA Server -- LANCan
View 7 Replies View RelatedI've got Cisco X2000 and WAG120N. Is it possible to use one of those as a kind of a 'ADSL bridge' on to connected Sonic wall firewall ? How I picture it is that adsl connection is terminating on one of above Cisco boxes, which is connected via Ethernet or wan port to sonic wall, and it's only passing the adsl connection on to sonic wall which in result will end up with my ISP assigned IP address ?
View 1 Replies View RelatedI'm trying to get confirmation on whether you can have workgroup bridge mode on the 1040 series model.
The 1041N has the same IOS as the 1141/1241 and it has the settings are there, but I read somewhere on the cisco site that workgroup bridge is only supported on 1100 and 1200 series, is this correct or old information?
Scenario is: I have an existing stand alone 1041N AP, on the other side of the building I have a network LAN switch with a couple of PCs, instead of running cables I would like to add an AP as a bridge to link that switch and PCs to the network that the AP is plugged in to. I believe this is called Workgroup Bridge Mode. In fact there already is a cheap non-cisco wireless device doing this but it is unreliable.
I just placed an order for Two 1041N APs, do I need to change the order to Two 1141N instead?
Also even if the 1041N does not support workgroup bridge mode, can it still act as the ROOT Bridge and have 2 1141N APs configured in bridge mode connected to the 1041N?
I'm currently researching in buying a new modem/router that must have the PPPoA support for the ISP, i'm wondering if the X3000 is compatible with the DD-WRT firmware? or in this case any other firmware that has a top notch QoS, We have a troll in the house that downloads too many torrents and would like to limit his bandwidth .
View 1 Replies View RelatedI am having problems with my linksys wireless G ADSL gateway WAG54GS router. I am on Windows Vista/Internet Explorer. When I set up the router to work on the internet when I first bought it (several years ago), something must have gone wrong in the installation because it works only when connected to the computer by the lead, and NOT wirelessly.
While this is fine for general internet browsing etc on the main computer, my problem now is that I cannot connect anything else to it (such as my Playstation 3) because the router does not work wirelessly and I do not have the WPA key that the PS3 asks for. Is there any way can fix this without doing a complete reset on the router?
[ALSO: the router also periodically goes wrong, e.g. loses connection for no reason at all - I often have to disable and then enable the internet connection, or turn the router off for 15 seconds then switch it on again, and then it's fine again. I live in a rural area though, so it might be because of a poor connection. Our telephone connecton isn't very good either and sometimes goes wrong.]
do WAG54GP2 routers have wds support? if they support, how can i configure?
View 1 Replies View Relatedhow to make in WAG320N second PVC for IP TV. It looks like unsupportable feature May be next firmware will include it? Or better to change the device? What Linksys with ADSL are support IP TV?
View 3 Replies View RelatedDoes WAG120N Support IPv6 ?
View 1 Replies View RelatedI have not found the information. Does linksys WAG54GX2 router support WDS?
View 1 Replies View RelatedI try to start with UPNP in my LAN network. Everyting works if I use Wifi connection but does not for wire connections. All tests suggest that router block UPNP traffic. Of course my WAG 200G in managment menu is for UPNP enabled. ex. downgrade firmware or something like this?
View 2 Replies View RelatedWould like to see IPv6 support on the WAG320N. Some ISPs now support this protocol....should eventually become a standard feature.
View 1 Replies View RelatedToday i brought Linksys X3000 and that came with old firmware version (1.0.01). i need new version (1.0.03) Annex A firmware but support page not working.
Support Page is not working: [URL]
