Linksys Cable / DSL :: WAG54GS Reconnecting Two Routers Wired
Jul 24, 2012
I have an old router linksys WAG54GS and now with my new internet connection gave me a HUAWEI 530.I'm still using linksys.So i wanted to connect the HUAWEI on the Linksys cause it has an external button for wireles, which Linksys doesnt.I followed the wizard you wrote.The DHCP off on the HUAWEI Different IP.So the Wired LAN worked fine, having an IP from the Linksys, but the wireless doesnt get one..I tried a lot of things on the huawei, nat off etc but nothing On the linksys i give on DHCP IPs from 192.168.1.105 - 7.I tried connect the netbook but only wired worked, not even my cellphone.
View 2 Replies
ADVERTISEMENT
May 10, 2012
My router refuses to link to the internet. Status indicates Interface: Down. I thought this was probably a firmware upgrade issue but can only find v1.01.03 which is already installed. Linksys website has no firmware listed for download.
I have downloaded and re-installed the v1.01.03 .img file with no effect. Is this the latest firmware for this model?
View 1 Replies
View Related
Feb 13, 2011
The subject syas it all really, I've spent all evening trying to get this to work, firmware is now on 1.01.05 and still no luck. Maybe it just doesn't support it?
View 1 Replies
View Related
May 21, 2011
I'm using a WAG54GS 1.0 router with up to date firmware, and signal around the house has always been fine, yet today it has suddently dropped to a VERY limited range - I'm sat right next to it now on a laptop and the signal is 2/5 bars - "fair".I've reset factory settings yet to no avail, I can't even get signal in the next room!
View 1 Replies
View Related
Jul 30, 2012
I need to upgrade my WAG54GS, but there is no firmware in support. My latest firmware is V1.01.03. Where can I download it?
View 4 Replies
View Related
Mar 19, 2011
I'm using an RFC 1483 Bridged adsl connection on a WAG54GS router. Downstream rate says 2043 Kbps, and upstream rate only 35 Kbps. In the router setup page I have not found any place to change downstream/upstream rates. How can I increase \the upstream rate?
View 2 Replies
View Related
Jun 1, 2009
i'm setting up a wireless network for a local B&B they currently have a Linksys WAG54GS ADSL router in one of the rooms but need the wireless signal to reach each guest room the house has thick brick walls and an upstairs.i was thinking of using 2 x repeaters, the WRE54G's, and to put one on the ground floor within range of the current ADSL router and to put another on the 1st floor within range of the repeater on the ground floor to receive the bounced signal.I don't know much about these repeaters and how they work exactly and so unsure if this would be a viable solution in my case.
View 6 Replies
View Related
Jul 17, 2011
I've been having a problem the past several days with my wired connection where every 2-3 seconds it will disconnect, then reconnect, then disconnect, and so on without stopping. There doesn't seem to be any reason for it, and it's not the internet connection but rather the physical connection that seems to be lost (the network will do the entire identifying...unidentified network > identified network thing).
Naturally, I've already tried upgrading my network card drivers + uninstalling/reinstalling when it didn't work. I've powercycled the router/modem and rebooted the comp, but I can't find any way to fix the issue. It's not a problem with the router, since this only happens on my computer, and the other computers connected to the router have no problems at all. Even if I disconnect the router and connect my computer directly to the modem, it still has the issue.
Normally I'd assume it was something wrong with my network adapter, but my computer has no problems connecting to a new router/network it's never been on before. This only happens with networks that my computer has connected to in the past.
Recently I've just been using the wireless connection since it was only the wired connection having issues, but a few days ago my wireless connection started doing the exact same thing. It'll disconnect/reconnect ad infinitum without stopping every few seconds, so it's impossible to get on the internet.
Here are the results of my ipconfig:
Quote:
C:UsersOwner>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : MainComputer
[Code]....
View 9 Replies
View Related
Mar 14, 2013
Our family has about three computers that use a wireless network that we all share. We have an old Gateway, a WCG200, that is bridged to an E2000, which was set-up ever since we required better security when someone used our connection to illegally obtain movies. We got a letter which warned us of any future violations that could cause legal action, so we looked into our wireless connection to better secure it from any other individuals outside of our household. The WCG200 is connected to the outlet in the wall via cable, and then connects from the Ethernet to the E2000. The E2000 has a stronger security setup than the WCG200, which is the advice we received from our ISP and would allow us to keep the Gateway. It provides a strong signal, but from time to time, we suffer latency or slow loading through all of our online devices, even though our connection speed displays a solid 72.0 Mbps. I've tried the Event Viewer to see any problems, and I have noticed some small things:
- WLAN AutoConfig service has successfully stopped.Wirel?
- WLAN Extensibility Module has stopped. Module Path: C:WindowsSystem32cmihvsrv64.dll
- The server {E10F6C3A-F1AE-4ADC-AA9D-2FE65525666E} did not register with DCOM within the required timeout.
- Broadcom NetLink (TM) Gigabit Ethernet: The network link is down. Check to make sure the network cable is properly connected. [This last one is strange, since I use the Wireless Network Connection with a DW1501 Wireless-N WLAN Half-Mini Card, while the Broadcom adapter is under the Local Area Connection and displayed as not connected.]
Other than that, I'm not quite sure what the recurring problem comes from. Our WCG200 has a firewall enabled and our E2000 has an SPI firewall enabled. The security mode of the E2000 is a WPA2 setup. We have disabled the wireless network of our WCG200 in order to make use of the E2000.
View 9 Replies
View Related
Sep 14, 2011
I have a home network with a wired BEFSR41 that, for a variety of reasons, MUST be manually IP configured (DHCP off). All computers and other devices connected to it are manually IP configured. I desire to add a device that cannot be manually configured, and needs DHCP. I therefore need to daisy-chain two routers with the second one DHCP on (and manual IP connection to the main network). The new device needs two-way internet access, but doesn't care if it sees any other current network devices. I've tried several configurations, none seem to work.
View 3 Replies
View Related
Feb 20, 2013
I am wondering if it is possible to Create a wireless bridge. I am trying to connect a linksys WAG54gs to next doors wireless router. It's ok she's my mother in law.
She has a BT home hub 3.
View 1 Replies
View Related
Jun 17, 2011
How do I turn off the SIP ALG?
View 1 Replies
View Related
Dec 29, 2012
Right now on my internet, we have U-Verse, so one router is the AT&T U-Verse one which is downstairs and I also have another router upstairs which is a Netgear oneThe problem is, the U-Verse always stays up, but on the Netgear router, it will sometimes randomly drop signal and the signal is no where to be found on devices with WiFi. I'd have to disconnect and reconnect the router for it to be seen again.They are both on the same internet network U-verse, I just have 2 routers because the devices I keep upstairs I connect to the upstairs router.
View 1 Replies
View Related
Apr 21, 2011
I am having problems with my linksys wireless G ADSL gateway WAG54GS router. I am on Windows Vista/Internet Explorer. When I set up the router to work on the internet when I first bought it (several years ago), something must have gone wrong in the installation because it works only when connected to the computer by the lead, and NOT wirelessly.
While this is fine for general internet browsing etc on the main computer, my problem now is that I cannot connect anything else to it (such as my Playstation 3) because the router does not work wirelessly and I do not have the WPA key that the PS3 asks for. Is there any way can fix this without doing a complete reset on the router?
[ALSO: the router also periodically goes wrong, e.g. loses connection for no reason at all - I often have to disable and then enable the internet connection, or turn the router off for 15 seconds then switch it on again, and then it's fine again. I live in a rural area though, so it might be because of a poor connection. Our telephone connecton isn't very good either and sometimes goes wrong.]
View 4 Replies
View Related
Apr 24, 2012
We have a linksys WAG54GS router the secure easy setup button of which was pressed instead of the on off switch when a reset was required. Now we can only browse the internet via a cable from the pc lan port to the router ethernet port. Things done :- Secure easy setup button held down for 10 seconds. Router went to an unsecured one now back to secure.
View 3 Replies
View Related
Jan 4, 2013
I am looking to replace my current WAG54GS Gateway with the EA6500. Problem is the new one does not have a built in ADSL2+ modem (I am in the UK and my ISP is Demon Internet). I therefore need to purchase a separate Modem to connect to the router.
View 9 Replies
View Related
Mar 26, 2013
In common with some other reports, I've been having a problem with a keep-alive tunnel between a RV016 and a RV042 not reconnecting if the tunnel is interrupted (by the WAN connection going down). In this event the only remedies are to manually connect the tunnel or to power cycle the routers. The firmware is v4.2.1.02 on both routers.I solved the problem by enabling keep-alive on the RV016 and disabling keep-alive on the RV042. If I set it the other eay around (RV042 keep-alive and RV016 not) then it will not reconnect automatically.
View 6 Replies
View Related
Dec 18, 2012
We have numerous customers using Cisco / Linksys RV042 VPN firewall devices to connect to a central location via VPN tunnels. We have noticed that if there is an interruption to any of the tunnels, the RV042 v2 devices will re-establish the tunnel automatically, however the RV042 v3 devices will typically fail to automatically re-establish the connection and will usually require somebody to repower the RV042 or for somebody to clear the crypto session from the central router and then manually connect the tunnel from the RV042's VPN menu.
One of my colleagues setup two RV042 v2 devices for a site to site VPN for a customer and it worked fine. At some point they replaced one of the RV042 devices with a v3 device and since then they are having the same issue.We have this problem with several different version of the RV042 v3 firmware including the latest (4.2.1.02).
View 1 Replies
View Related
Oct 23, 2010
my modem/router WAG320N works ok but wireless client can't see wired and vice versa. they are in the same network (192.168.0. ), using the same 255.255.255.0 mask, same workgroup and yes firewalls allowing all packets in and out. IP addresses are form DHCP.
internet sharing works ok, but when im trying to play any game on LAN wireless clients can see them self but not the wired one. when im trying to ping wireless client from a wired machine it doesn't work either.
what's intresting in a DHCP reservation or ARP table (in router setup) i can see both wired and wireless clients. but still they can not see each other.
View 8 Replies
View Related
Jan 31, 2013
The X3000 functions as a router/gateway between the ADSL network, its wireless network (WPA2) and its wired network. After a cold start, factory reset and restore of the config file everything works fine. I have interconnection between all three parts of my network. However after ± 24 hour there is no connection possible anymore from the wired to the wireless network and vice versa. A normal power off - power on will not work. The only thing that works is running the factory reset procedure as discribed above. I changed the MTU to manual 1400 as was suggested on this forum, but that does not work. Apart from this issue, ADSL is hicks sometimes. From my ISP I heard that at certain times my router issues ten's of DHCP requests within one minute, while the connection (modem) remains perfect. I have the impression that after such a DHCP request storm to my ISP, the interconnection between my X3000 wireless network and my X3000 wired network is lost.
View 4 Replies
View Related
Nov 6, 2012
I have my broadband line feeding into a WAG 320N in an outside room. There are computers in the outside room which are wired to the modem via CAT leads & plugs. Wireless is turned on, but is not currently being used in this room, as the wired connections work fine. From this outside room there is an underground cable (12 metres) to the house, which through a CAT lead is plugged into another WAG 320N, which operates primarily wirelessly, so laptop computers can be used in the house wirelessly. When the outside room modem is turned on AND the house modem is turned on, only one modem OR the other can access the internet, NOT BOTH. Why can't both modems operate wired and wirelessly. What is the problem? Is there a conflict between the two wireless signals? Can/ should I turn off the wireless signal from the outside modem (if so HOW?) . OR is there a way I can have both modems transmitting a wireless signal.
View 1 Replies
View Related
Feb 11, 2013
Im having a issue with that any of my computers without a wireless connection have been incapable of getting out on the internet with the new router that i got myself, i know the cables works etc, since they work perfectly fine with the old modem alone, but wont work at all with this unless on a computer with wireless connection
View 5 Replies
View Related
Sep 14, 2011
i have purchased WAG120N exactly one year back. Now I am facing a issue with modem.Power button is blinking and stabilizing after 5 minutes, but internet and wireless are not led's are not on and not receiving any signal from wireless and wired.I have called Linksys, they are not giving any support and saying one year warranty period is over.
View 1 Replies
View Related
Apr 19, 2012
I have a Linksys RV082 Wired router. It works great but doesn't do wireless. I have a Cisco/Linksys E2500 Wireless router for my wireless devices to use. the RV082 is on the 192.168.1.x network. The E2500 is on the network 192.168.0.x network. The Internet cable goes to the Wired RV082, and a line comes out of there to the wireless router. This all works fine except for a couple inconveniences.I have an iPad that connects wirelessly and some of the apps offer an http:// option so I can transfer files to that app. I also have a network printer hooked in wired, but wireless devices can't see it.I have 2 problems:
1) In order to transfer files from my laptop (which I have hooked in to the wired network most of the time), I have too disconnect the wire, connect wirelessly, then I can transfer the files. Works, but it's inconvenient.
2) I would like a netbook that I have on the wireless connection to be able to print to my wired network printer.
It appears that the 2 networks are not seeing each other. Here are the things that I have tried:
1) I disabled the DHCP on the wireless router. My thought is that requests for an IP address sent to the wireless router would be forwarded along to my wired router... NOT. On my iPad and Wii, they could no longer connect wirelessly. Strangely enough, with the wire disconnected and connecting wirelessly with my laptop, I was still getting a 192.168.0.x IP address, even though DHCP was disabled on the wireless router.
2) Thinking that I would just manually put the wireless router on the 192.168.1.x network, instead of telling it to get an IP dynamicaly from the Internet connection, I manually set it's IP to 192.168.1.245. Bad mistake. I could not connect to it at all from anywhere then. The only way I could fix that was to hook it wired to my notebook, assign a static IP to my notebook on the same network as the router, then I could got to the setup page and set things back the way it was.
Another thing... Even when I'm only connected wired on my notebook and wireless is disabled, I can ping 192.168.0.1 (the wireless gateway) and it returns a value. But, when I try to go there in a browser, I get a "page not found" error.
View 2 Replies
View Related
Jan 4, 2009
I am running a wrt54g and I was woundering what is the longest rj45 cable length I can run?
I notice running about 30 plus feet connection does not work. When I cut off about 5 feet it worked. Seems I can only run a ceratin amount of cable length with this router.
View 8 Replies
View Related
Nov 8, 2011
I am swapping my AT&T DSL and Comcast cable for U-verse. In the basement, I have a Netopia DSL modem connected to a Linksys BEFRS81 v. 3 ethernet Cable/DSL router/8-port switch. Cat 5 cables are attached to the router, then run throughout the house so we are "networked" to the DSL modem and use a patch cord from laptop or desktop into the wall to get to the Internet.
View 1 Replies
View Related
Jun 30, 2011
I have the cisco WAG120N router. In order to avoid constant radiation I would like to be able to connect my computer and router using an ethernet cable and if possible disconnect and use it wireless when I need more than one computers or netbooks to be connected to the internet. I tried to connect my computer with the router using an ethernet cable but I realized that I continued to have the wireless network on.
View 2 Replies
View Related
Aug 19, 2011
I have a Linksys BEFSX41 wired router. If I wanted to connect a second computer to my router, what would be the maximum length of cable I can use without experiencing any problems ?
View 3 Replies
View Related
Oct 30, 2012
I had to install a new modem for my Hughes Net satellite dish, and now my wireless laptop isn't connected to the router, meaning I can get online with it anymore.
View 2 Replies
View Related
Oct 7, 2011
I have been using this for over a year with no problems and a couple of days ago, it started disconnecting and reconnecting constantly. I went and updated the firmware for it, but still the same problem.
View 6 Replies
View Related
Apr 11, 2013
I have two Cisco RV042 Routers, they are being used to connect two offices, i have created a standard gateway to gateway connection, fixed public ip addresses on both sides and everything works fine, except when the tunnel gets disconnected, it does not connect back automatically, i have to log into either router console and click the connect button to get the tunnel working again, this is really annoying since it happens once or twice a day at least.
View 2 Replies
View Related
Feb 24, 2012
Comcast service went down in our neighborhood and when it came back up my internet was down and all five LED lights on my Linksys router are solid green. Tech support tells me that I have to reset the unit to get it to function again.It's been a very long time since I set up the home network and while I'm pretty sure I can make my way through setting up from scratch (I'm assuming resetting goes back to factory settings) I was hoping there was a way to reconnect the router to the modem while retaining all the current security and settings.
View 2 Replies
View Related
Nov 23, 2010
I was trying to remotely command my iTunes library via an iPhone app called Remote. It worked for some times with an intermittent disconnection problem due to the iPhone locking. But even after unlocking the phone and reconnecting the Wi-Fi, Remote couldn't find my iTunes library again and my only workaround was to relaunch iTunes on the PC (which is Ethernet-wired to my router). Few days ago nothing worked!!! I could no more get Remote to find iTunes.
I could not find a solution even by rebooting the router or unplugging the PC's Ethernet cable. Last night I powered off the router and after 10s I powered it on again. And then it worked!I highly suspect a problem between my router and Bonjour which is as UPnP, an Apple protocol for discovering communicating devices. Discovery phase being usually done with broadcast frames, something goes wrong in the router with processing the broadcasts, or is it a Bonjour problem?Please note that even now that Remote can find iTunes, I still have my old intermittent disconnection problem.So is there any incompatibility between WRT-610N and Bonjour and what is the fix ?
View 3 Replies
View Related
