Linksys Wired Router :: WAG120N Turn From Wireless To Cable And Vice Versa
Jun 30, 2011
I have the cisco WAG120N router. In order to avoid constant radiation I would like to be able to connect my computer and router using an ethernet cable and if possible disconnect and use it wireless when I need more than one computers or netbooks to be connected to the internet. I tried to connect my computer with the router using an ethernet cable but I realized that I continued to have the wireless network on.
View 2 Replies
ADVERTISEMENT
Mar 7, 2013
So IP from the same segment can ping each other fine. Problem is PC1 cannot ping PC3 vice versa. I have tried IpEnableRouter, route add, turn on routing and remote access services and nothing seem to be working? So my question is can Win7 or any windows for that matter are able to route traffic from 1 NIC to another?
View 1 Replies
View Related
Nov 25, 2012
I have a uc320 and router directly connected and I can ping the router from the 320 but cant ping the other way. As a result I only have SIP traffic working outbound but cant get and calls inbound.
View 2 Replies
View Related
Feb 20, 2011
Turn off wireless sending from WAG120N
View 1 Replies
View Related
Sep 14, 2011
i have purchased WAG120N exactly one year back. Now I am facing a issue with modem.Power button is blinking and stabilizing after 5 minutes, but internet and wireless are not led's are not on and not receiving any signal from wireless and wired.I have called Linksys, they are not giving any support and saying one year warranty period is over.
View 1 Replies
View Related
May 4, 2012
My WAG120N wireless router disconnects every hour, precisely at the same time. This problem has started a few days ago, until then everything was fine.When the connection is gone, the "Internet" light goes off, the other lights remain on. For example, it disconnects at 07:30. It takes a minute or two to reconnect. Then it disconnects at 08:31. It reconnects, and then disconnects at 09:32.. and so on.Here are the things that I have tried (with my limited knowledge.. I'm not good with technology):- Turned the power on/off. No matter what time I do this at, the router disconnects at the same time again. For example, if it last disconnected at 07:30, and I turn it off and on at 7:50, it still disconnects at 08:31.- I tried resetting it, by pushing and holding the reset button on the back for 30-60 seconds (did it several times). Reconfigured the router (manually, not from a backup config file). Same situation as above, disconnects at the same time as always.
- I upgraded the IOS to v1.00.16, which I found here: [URL] reset and then reconfigured again. Still it didn't work.- Looked in the configuration pages for any values that resemble a 60 minute time span, and changed them. Only thing I found was the security key renewal period. Or was I sold a faulty product?
View 6 Replies
View Related
Apr 29, 2011
I have been using it since approx 6months ago. Previously it was working well except for some major signal issues. However, 3 days ago it decided to go haywire. 1) It does not connect to the internet 2) It does not detect/connect to the computer when LAN cable is plugged in (does not load in 192.168.1.1) 3) I have tried resetting the router many times and even holding the reset button for 30 secs and switching off and switching on but to no avail. 4) I have had a linksys live chat with Johnel and he determined that it may be a possible hardware problem 5) Current Status of the Router: It makes no attempt to establish any connection/load whenever turned on, as seen when no lights are blinking when switched on. Upon switching on, Power Light becomes Red and Internet Light becomes Red and the middle Refresh Button become Red. 6) I have tried installing the driver for the router but there is no way I can install the driver because the computer does not detect that the router is connected What can I do about these? 1) Can I get a replacement of a different model? This router has been giving me problems since Day 1 2) I am seriously considering switching my service provider from M1 to Starhub. If that is the case, is there any way I can be replaced with a Cable Modem instead of ADSL Modem?
View 9 Replies
View Related
Jan 14, 2012
I am using wag120n modem router but is confused abt how to setup it's wireless security.The wireless securit setting recommended in tutorial given here is very different from what is given in my routrs setting up page.
I don't know how to handle the key renewal option.If i leave it as 3600 seconds does that mean i have to enter a new key in my wireless device connected to the router after every 1 hour?
View 2 Replies
View Related
Jul 20, 2011
How do I set up the WAG120N as a router only as I no longer want to use it as modem and router?I want to connect the WAG120N thru a cable to a modem that will make the internet connection and use the WAG120N as a wireless router only.
View 3 Replies
View Related
Jun 25, 2012
I just ordered the Linksys WAG120N modem/ router and need configuring the same on the BSNL network. Any Document or link about his Installation and configuration.
View 3 Replies
View Related
Dec 28, 2011
We are trying to play Call of Duty MW3. We have purchased two games and two xbox360s. We want to connect the two xboxs to the internet using a cisco wag120n router..
View 2 Replies
View Related
Sep 2, 2010
My WAG120N router overheating and stuck repeatedly every 4-5 hours. How i can solve this problem? I buy this router 3-4 months ago...Is hardware or software issue?
My WAG120N:
Firmware Version: V1.00.07
DDNS Service - Disable
DMZ Hosting - Disable
Firewall - Disable
Restore to Factory Setting - Many Times = No result
Connected Computers in the LAN - WLAN = 6 Desktops-Laptops, 3 PDA Devices
--> My Router gives this information about my Downstream / Upstream Rate
Downstream Rate: 10229 kbps
Upstream Rate: 861 kbps
View 2 Replies
View Related
Jun 1, 2011
I have a 3G USB modem connected to my desktop and I would like to share the internet connection to other devices wirelessly using the WAG120n ADSL router. How do I set up the IP's manually on the router and my PC to do this? And which other setting do I need to set?
View 1 Replies
View Related
Dec 26, 2011
I recently purchased the Linksys Wireless N Home WAG120N and I've hooked it up correctly but I can't seem to establish a connection with the DSL light. I've tried hooking it up to different ends in my house with no improved results, however, my older modem works fine.
View 1 Replies
View Related
Nov 21, 2012
Now unable to connect laptop wirelessly. The laptop can see the connection, but when I click it to connect it just doesn't. Have tried rebooting both laptop, desktop and modem, left it overnight, can't connect smartphone to it either. All were working perfectly until I had to reinstall.
View 6 Replies
View Related
Jan 1, 2013
I have a linksys WAG120N router updated to 1.00.16and I have Wi-Fi problems that while I use Wi-Fi on my laptop or mobile then the Wi-Fi disconnected (wifi on router still green but i can't connect ) until i restart router.
View 7 Replies
View Related
Jun 26, 2012
My WAG120N router has stopped working completely. None of the Ethernet ports or the wi-fi signal button is lit,power light continues to blink for 10 odd mins and then comes to a rest. Tried to login to admin portal without any success, tried to reset it pressing the reset button in the back without any success.Tried the 30-30-30 reset method without success too.
View 3 Replies
View Related
Jan 5, 2012
I am using the WAG-120 N as an AP and switch for 3 laptops and 2 desktops. Our department is assigned only one Static IP from our server, so only one pc can connect to the server and the internet. I use the first lan port of the Wag-120N as a WAN port and i assign the Static IP address there, along with the subnet, default gateway and DNS addresses. The connected clients are assigned then an ip address from the router's DHCP (192.168.1.10x), but cannot connect to the internet. How can i configure the router to allow the clients to connect?
View 9 Replies
View Related
Jul 7, 2011
am using cisco linksys wag120n. how much length of wireless range will i get?
View 2 Replies
View Related
Jun 8, 2010
I purchased WAG120N Wireless-N ADSL Gateway today.I configured it properly, my wired connections are fine and internet is running but i am facing problems in connecting it to my iPod touch 1G....it shows the SSID in the iPod but when i connect it says "unable to join".
View 9 Replies
View Related
May 15, 2013
i just bought a sony lcd tv and this model can be controlled by a smartphone via an app called mediaremote. The app should scan the local network and find the tv and than, after pairing, you can use the smartphone as remote controller over Wi-Fi.
My problem is that the router block the network scan and the app can't find the tv; is there somethig i can chack in the configuration or that else to permit the local network scan?
I tried to connect tv and smartphone to the neighbour wifi and the app woks perfect so i'm sure that is a my network problem.
View 3 Replies
View Related
Jul 1, 2012
My house has 2 floors.In the first floor i have a wag160n connected to adsl internet.On the second floor i want to use my old wag120n to connect wirelessly to the router in the first floor and redistribute the internet through his ethernet ports(through wag120n ethernet ports).I want to do this because on the second floor where the tv is i want to connect a dreambox that has only ethernet connection so i can give internet to it via the wag's 120n ethernet ports.
View 2 Replies
View Related
Apr 1, 2013
I have 802.11n wireless network at home. Unfortunately my TV box requires internet to work and it doesn't have wifi card installed (only ethernet port). It's very unconfortable to connect tv box with the router through cable.
So is it possible to use WAG120N as a wireless client for my existing wifi network and connect tv box through cable with WAG120N? In that case WAG120N would be some kind of wireless network adapter for my TV box.
View 4 Replies
View Related
Mar 23, 2013
I have had trouble setting my WAG120N as router.
I am connected to internet via a cable modem, via the LAN cable, I connect cable modem to WAG120N that I want to use as an wireless access point only. And I have got 2 PC, 1 runs on XP, the other on runs on Windows 7. My XP would have no trouble to connect to wireless, but the Win7 can only connect to wireless network, but no internet. When I try the troubleshooting from Win 7, it says, DNS server isnt responding The setting I am using at the moment is Bridged mode only, without entering any values of DNS, IP, etc Is there any setting that work for both OS?
View 1 Replies
View Related
Feb 8, 2011
Just installed a new WAG120N for a customer.All works fine except when I go to her sleep out, not more than 6 meters away - no connectivity through wireless, so bad that it doesn't even see it - this is with two separate laptops.The walls are nothing special - wood outside, wool fiber insulation & gib board inside.Roof standard corrugated iron.
View 1 Replies
View Related
Jan 11, 2012
I have an issue with my router that disconnects from the internet in variuos situation when my laptop (an hp pavillion dv6) try to connect. It happen everytime when the laptop go in standby. When i turn it on from standby, the router disconnects from the net and the only way to have access to internet again is turn off and then on the router. It happens also when i turn on the laptop if there is yet some other device connected, like my desktop or my iphone or whatever.
Sometimes i have the same problem with my brand new tablet (a sony s) in a slightly different way. I navigate then, after a random amount of time, the router disconnects in the same way and the only way to have back connection is turn off and then on the router.
View 2 Replies
View Related
Jul 17, 2010
I've noticed something interesting, after having been disconnected from the WLAN in less than 1 minute in my first experience with this Linksys' Modem Router: The signal strength was poor when browsing the Wireless LAN. I was at home, in a room just beside the one where the router was placed at.So, I took a look at connection status, and saw the signal strength was Medium - Weak: something around 30% and 55% You could think it was due to mirrors, the kind of walls between the rooms, and everything else, but I instantly remembered when browsing WLAN from the same place but not with the same router, the signal was strong (100%)...but I let it alone In the other day, while browsing WLAN, I've noticed another thing, this time visible: "TX power" I've got in connection status was 39mW, while I was almost sure it should be 100mW, based on my past WLAN connections Then, today I decided to take a look more deeply in that, and unboxed my Linksys' WRT54G to test. The test was carried on consisting in both Wireless routers placed in the same room, and a solid wall was between me and the routers.I could connect to the two WLANs, but the status of connections were different.
WAG120N:
WRT54G:
As you can see, when connecting to WRT54G , signal reached 100% at some point, whereas in WAG120N , such a mark wasn't possible.Of course, the signal strength was unstable in both routers, but the average level in WRT54G WLAN was greater, being most of time over 90%, and never below 80%.In WAG120N WLAN, average was 82%, and lowest level was 55%.When I went to the room where the routers were at, and right in front of them, no need to say both reached 100%, but as you can see, in WAG120n's case, TX power was still 39mw: I believe it's a firmware fault, once all other routers I've connected to always showed TX power as being 100mW.It shoundn't be related to the general hardware, as Cisco products are high-quality ones.
View 9 Replies
View Related
Dec 17, 2011
I am connecting to the internet in two desktops using the WAG120N modem+router.I have no problems with the internet. But when I try to use the wireless access point in my mobile phone / laptop,the device is not able to find the WiFi access point. I need to swith off the modem and start it again, then the devices are finding the access point. I guess this has to do with some amount of inactivity and the modem switces off the wireless access point. I there anyway by which I can turn off that setting ? I have tried the setting page but was not able to find anything.
View 6 Replies
View Related
Mar 11, 2011
i'v recently bought a WAG120N for my home and set it up after that i checked that my wireless link speed on my laptop is 72mbps instead 150mbps after a few googling ive found that 150mbps is only avalaible on 40MHz radio band but in setup page i only found 20MHz.
View 2 Replies
View Related
May 25, 2011
I've had enough of BT's shoddy Home Hub router dying whenever I transfer large files over wifi so I want to go back to a trusty Linksys and I'm looking at the WAG320N.
I've got a family member who is convinced wifi is harmful, so to avoid an argument I've agreed to switch it off at night. My last Linksys let me do this via a custom firmware, but the WAG320N isn't a Linux based model. So, my question is: can I set wifi to switch itself off at night from e.g. 11pm until 8am? Preferably this will be an actual switch-off rather than just preventing access via certain wifi devices.
If it can't do it, any alternative Linksys ADSL2+ modem that can?
View 2 Replies
View Related
Apr 19, 2012
I have a Linksys RV082 Wired router. It works great but doesn't do wireless. I have a Cisco/Linksys E2500 Wireless router for my wireless devices to use. the RV082 is on the 192.168.1.x network. The E2500 is on the network 192.168.0.x network. The Internet cable goes to the Wired RV082, and a line comes out of there to the wireless router. This all works fine except for a couple inconveniences.I have an iPad that connects wirelessly and some of the apps offer an http:// option so I can transfer files to that app. I also have a network printer hooked in wired, but wireless devices can't see it.I have 2 problems:
1) In order to transfer files from my laptop (which I have hooked in to the wired network most of the time), I have too disconnect the wire, connect wirelessly, then I can transfer the files. Works, but it's inconvenient.
2) I would like a netbook that I have on the wireless connection to be able to print to my wired network printer.
It appears that the 2 networks are not seeing each other. Here are the things that I have tried:
1) I disabled the DHCP on the wireless router. My thought is that requests for an IP address sent to the wireless router would be forwarded along to my wired router... NOT. On my iPad and Wii, they could no longer connect wirelessly. Strangely enough, with the wire disconnected and connecting wirelessly with my laptop, I was still getting a 192.168.0.x IP address, even though DHCP was disabled on the wireless router.
2) Thinking that I would just manually put the wireless router on the 192.168.1.x network, instead of telling it to get an IP dynamicaly from the Internet connection, I manually set it's IP to 192.168.1.245. Bad mistake. I could not connect to it at all from anywhere then. The only way I could fix that was to hook it wired to my notebook, assign a static IP to my notebook on the same network as the router, then I could got to the setup page and set things back the way it was.
Another thing... Even when I'm only connected wired on my notebook and wireless is disabled, I can ping 192.168.0.1 (the wireless gateway) and it returns a value. But, when I try to go there in a browser, I get a "page not found" error.
View 2 Replies
View Related
Mar 14, 2013
Our family has about three computers that use a wireless network that we all share. We have an old Gateway, a WCG200, that is bridged to an E2000, which was set-up ever since we required better security when someone used our connection to illegally obtain movies. We got a letter which warned us of any future violations that could cause legal action, so we looked into our wireless connection to better secure it from any other individuals outside of our household. The WCG200 is connected to the outlet in the wall via cable, and then connects from the Ethernet to the E2000. The E2000 has a stronger security setup than the WCG200, which is the advice we received from our ISP and would allow us to keep the Gateway. It provides a strong signal, but from time to time, we suffer latency or slow loading through all of our online devices, even though our connection speed displays a solid 72.0 Mbps. I've tried the Event Viewer to see any problems, and I have noticed some small things:
- WLAN AutoConfig service has successfully stopped.Wirel?
- WLAN Extensibility Module has stopped. Module Path: C:WindowsSystem32cmihvsrv64.dll
- The server {E10F6C3A-F1AE-4ADC-AA9D-2FE65525666E} did not register with DCOM within the required timeout.
- Broadcom NetLink (TM) Gigabit Ethernet: The network link is down. Check to make sure the network cable is properly connected. [This last one is strange, since I use the Wireless Network Connection with a DW1501 Wireless-N WLAN Half-Mini Card, while the Broadcom adapter is under the Local Area Connection and displayed as not connected.]
Other than that, I'm not quite sure what the recurring problem comes from. Our WCG200 has a firewall enabled and our E2000 has an SPI firewall enabled. The security mode of the E2000 is a WPA2 setup. We have disabled the wireless network of our WCG200 in order to make use of the E2000.
View 9 Replies
View Related
Aug 24, 2012
Is there any way to disable WPS feature on my WAG120?
View 1 Replies
View Related
