Linksys Cable / DSL :: WAG120N Not Receiving Any Signal From Wireless And Wired

Sep 14, 2011

i have purchased WAG120N exactly one year back. Now I am facing a issue with modem.Power button is blinking and stabilizing after 5 minutes, but internet and wireless are not led's are not on and not receiving any signal from wireless and wired.I have called Linksys, they are not giving any support and saying one year warranty period is over.

View 1 Replies


ADVERTISEMENT

Linksys Cable / DSL :: WAG120N Signal Strength Was Poor When Browsing Wireless LAN

Jul 17, 2010

I've noticed something interesting, after having been disconnected from the WLAN in less than 1 minute in my first experience with this Linksys' Modem Router:  The signal strength was poor when browsing the Wireless LAN.    I was at home, in a room just beside the one where the router was placed at.So, I took a look at connection status, and saw the signal strength was Medium - Weak: something around 30% and 55% You could think it was due to mirrors, the kind of walls between the rooms, and everything else, but I instantly remembered when browsing WLAN from the same place but not with the same router, the signal was strong (100%)...but I let it alone  In the other day, while browsing WLAN, I've noticed another thing, this time visible: "TX power" I've got in connection status was 39mW, while I was almost sure it should be 100mW, based on my past WLAN connections Then, today I decided to take a look more deeply in that, and unboxed my Linksys' WRT54G to test.  The test was carried on consisting in both Wireless routers placed in the same room, and a solid wall was between me and the routers.I could connect to the two WLANs, but the status of connections were different.  

WAG120N:

WRT54G:

As you can see, when connecting to WRT54G , signal reached 100% at some point, whereas in WAG120N , such a mark wasn't possible.Of course, the signal strength was unstable in both routers, but the average level in WRT54G WLAN was greater, being most of time over 90%, and never below 80%.In WAG120N WLAN, average was 82%, and lowest level was 55%.When I went to the room where the routers were at, and right in front of them, no need to say both reached 100%, but as you can see, in WAG120n's case, TX power was still 39mw: I believe it's a firmware fault, once all other routers I've connected to always showed TX power as being 100mW.It shoundn't be related to the general hardware, as Cisco products are high-quality ones.

View 9 Replies View Related

Linksys Cable / DSL :: WAG120N And AE1000 PC Bus Signal Is Low

Jul 11, 2012

i have a problem whit Modem Router WAG120N and linksys AE1000 router is 5 meter my pc bus signal is low

View 1 Replies View Related

Linksys Cable / DSL :: WAG120n Having Very Poor Signal Strength

Jun 7, 2010

I have a linksys router WAG 120n and when using wireless if I move into the next room the signal strength goes down to 40% there is only one single wall in between the room and the router. I have upgraded the firmware to the latest version turned off other electrical devices changed the wireless channels but none of this has worked. Any more settings I can try to get the signal stronger, I really don't want to return the router unless completely necessary.

View 4 Replies View Related

Linksys Wired Router :: WAG120N Turn From Wireless To Cable And Vice Versa

Jun 30, 2011

I have the cisco WAG120N router. In order to avoid constant radiation I would like to be able to connect my computer and router using an ethernet cable and if possible disconnect and use it wireless when I need more than one computers or netbooks to be connected to the internet. I tried to connect my computer with the router using an ethernet cable but I realized that I continued to have  the wireless network on.

View 2 Replies View Related

Linksys Cable / DSL :: Wireless Range Of Wag120n?

Jul 7, 2011

am using cisco linksys wag120n. how much length of wireless range will i get?

View 2 Replies View Related

Linksys Cable / DSL :: Wireless Connectivity In WAG120N?

Jun 8, 2010

I purchased WAG120N Wireless-N ADSL Gateway today.I configured it properly, my wired connections are fine and internet is running but i am facing problems in connecting it to my iPod touch 1G....it shows the SSID in the iPod but when i connect it says "unable to join".

View 9 Replies View Related

Linksys Cable / DSL :: Using Wag120N In Wireless Client Mode?

Jul 1, 2012

My house has 2 floors.In the first floor i have a wag160n connected to adsl internet.On the second floor i want to use my old wag120n to connect wirelessly to the router in the first floor and redistribute the internet through his ethernet ports(through wag120n ethernet ports).I want to do this because on the second floor where the tv is i want to connect a dreambox that has only ethernet connection so i can give internet to it via the wag's 120n ethernet ports.

View 2 Replies View Related

Linksys Cable / DSL :: WAG120N Wireless Router Disconnects?

May 4, 2012

My WAG120N wireless router disconnects every hour, precisely at the same time. This problem has started a few days ago, until then everything was fine.When the connection is gone, the "Internet" light goes off, the other lights remain on. For example, it disconnects at 07:30. It takes a minute or two to reconnect. Then it disconnects at 08:31. It reconnects, and then disconnects at 09:32.. and so on.Here are the things that I have tried (with my limited knowledge.. I'm not good with technology):- Turned the power on/off. No matter what time I do this at, the router disconnects at the same time again. For example, if it last disconnected at 07:30, and I turn it off and on at 7:50, it still disconnects at 08:31.- I tried resetting it, by pushing and holding the reset button on the back for 30-60 seconds (did it several times). Reconfigured the router (manually, not from a backup config file). Same situation as above, disconnects at the same time as always.
 
- I upgraded the IOS to v1.00.16, which I found here: [URL] reset and then reconfigured again. Still it didn't work.- Looked in the configuration pages for any values that resemble a 60 minute time span, and changed them. Only thing I found was the security key renewal period. Or was I sold a faulty product?

View 6 Replies View Related

Linksys Cable / DSL :: Turn Off Wireless Sending From WAG120N

Feb 20, 2011

Turn off wireless sending from WAG120N

View 1 Replies View Related

Linksys Cable / DSL :: WAG120n - Wireless Network Adapter For TV Box

Apr 1, 2013

I have 802.11n wireless network at home. Unfortunately my TV box requires internet to work and it doesn't have wifi card installed (only ethernet port). It's very unconfortable to connect tv box with the router through cable.
 
So is it possible to use WAG120N as a wireless client for my existing wifi network and connect tv box through cable with WAG120N? In that case WAG120N would be some kind of wireless network adapter for my TV box.

View 4 Replies View Related

Cat5 From Computer Receiving Wireless Signal?

Jul 18, 2011

I have a computer that is directly connected to my internet broadband service via my router and modem. From that computer, by use of a router (of course), I have a wireless connection to another desktop computer in my home, about 90 feet away.From that remote wireless internet broadband connection, I'd like to connect to yet a third computer. That third computer will be 200 more feet away. I have a direct Cat5 wire from the wireless computer desktop to that point 200 feet away. I'm thinking of adding a computer at that point.So, that raises my question: Can a computer receiving a wireless signal, then relay or transmit that signal to another computer that is "hard wired" to it via a Cat5 wire?

View 8 Replies View Related

Linksys Cable / DSL :: WAG120N Setting As Wireless Access Point?

Mar 23, 2013

I have had trouble setting my WAG120N as router.

I am connected to internet via a cable modem, via the LAN cable, I connect cable modem to WAG120N that I want to use as an wireless access point only. And I have got 2 PC, 1 runs on XP, the other on runs on Windows 7. My XP would have no trouble to connect to wireless, but the Win7 can only connect to wireless network, but no internet. When I try the troubleshooting from Win 7, it says, DNS server isnt responding The setting I am using at the moment is Bridged mode only, without entering any values of DNS, IP, etc Is there any setting that work for both OS?

View 1 Replies View Related

Linksys Cable / DSL :: WAG120N Wireless Router Hardware Failure?

Apr 29, 2011

I have been using it since approx 6months ago. Previously it was working well except for some major signal issues. However, 3 days ago it decided to go haywire. 1) It does not connect to the internet 2) It does not detect/connect to the computer when LAN cable is plugged in (does not load in 192.168.1.1) 3) I have tried resetting the router many times and even holding the reset button for 30 secs and switching off and switching on but to no avail. 4) I have had a linksys live chat with Johnel and he determined that it may be a possible hardware problem 5) Current Status of the Router: It makes no attempt to establish any connection/load whenever turned on, as seen when no lights are blinking when switched on. Upon switching on, Power Light becomes Red and Internet Light becomes Red and the middle Refresh Button become Red. 6) I have tried installing the driver for the router but there is no way I can install the driver because the computer does not detect that the router is connected What can I do about these? 1) Can I get a replacement of a different model? This router has been giving me problems since Day 1 2) I am seriously considering switching my service provider from M1 to Starhub. If that is the case, is there any way I can be replaced with a Cable Modem instead of ADSL Modem?

View 9 Replies View Related

Linksys Cable / DSL :: WAG120N When Go To Sleep Out Not More Than 6 Meters Away / No Connectivity Through Wireless

Feb 8, 2011

Just installed a new WAG120N for a customer.All works fine except when I go to her sleep out, not more than 6 meters away - no connectivity through wireless, so bad that it doesn't even see it - this is with two separate laptops.The walls are nothing special - wood outside, wool fiber insulation & gib board inside.Roof standard corrugated iron.

View 1 Replies View Related

Linksys Cable / DSL :: WAG120N / Unable To Find Wireless Access Point

Dec 17, 2011

I am connecting to the internet in two desktops using the WAG120N modem+router.I have no problems with the internet. But when I try to use the wireless access point in my mobile phone / laptop,the device is not able to find the WiFi access point. I need to swith off the modem and start it again, then the devices are finding the access point. I guess this has to do with some amount of inactivity and the modem switces off the wireless access point. I there anyway by which I can turn off that setting ? I have tried the setting page but was not able to find anything.

View 6 Replies View Related

Linksys Cable / DSL :: Wag120n Modem Router Wireless Security Setting?

Jan 14, 2012

I am using wag120n modem router but is confused  abt how to setup it's wireless security.The wireless securit setting recommended in tutorial given here is very different from what is given in my routrs setting up page.
 
I don't know how to handle the key renewal option.If i leave it as 3600 seconds does that mean i have to enter a new key in my wireless device connected to the router after every 1 hour?

View 2 Replies View Related

Linksys Cable / DSL :: WAG120N Wireless Link Speed On Laptop Is 72mbps Instead 150mbps

Mar 11, 2011

i'v recently bought a WAG120N for my home and set it up after that i checked that my wireless link speed  on my laptop is 72mbps instead 150mbps after a few googling ive found that 150mbps is only avalaible on 40MHz radio band but in setup page i only found 20MHz.

View 2 Replies View Related

Linksys Cable / DSL :: WCG200 Bridge Mode From Wireless-G Cable Gateway To Wired?

Mar 14, 2013

Our family has about three computers that use a wireless network that we all share. We have an old Gateway, a WCG200, that is bridged to an E2000, which was set-up ever since we required better security when someone used our connection to illegally obtain movies. We got a letter which warned us of any future violations that could cause legal action, so we looked into our wireless connection to better secure it from any other individuals outside of our household. The WCG200 is connected to the outlet in the wall via cable, and then connects from the Ethernet to the E2000. The E2000 has a stronger security setup than the WCG200, which is the advice we received from our ISP and would allow us to keep the Gateway. It provides a strong signal, but from time to time, we suffer latency or slow loading through all of our online devices, even though our connection speed displays a solid 72.0 Mbps. I've tried the Event Viewer to see any problems, and I have noticed some small things:

- WLAN AutoConfig service has successfully stopped.Wirel?

- WLAN Extensibility Module has stopped. Module Path: C:WindowsSystem32cmihvsrv64.dll

- The server {E10F6C3A-F1AE-4ADC-AA9D-2FE65525666E} did not register with DCOM within the required timeout.

- Broadcom NetLink (TM) Gigabit Ethernet: The network link is down.  Check to make sure the network cable is properly connected. [This last one is strange, since I use the Wireless Network Connection with a DW1501 Wireless-N WLAN Half-Mini Card, while the Broadcom adapter is under the Local Area Connection and displayed as not connected.]

Other than that, I'm not quite sure what the recurring problem comes from. Our WCG200 has a firewall enabled and our E2000 has an SPI firewall enabled. The security mode of the E2000 is a WPA2 setup. We have disabled the wireless network of our WCG200 in order to make use of the E2000.

View 9 Replies View Related

Linksys Cable / DSL :: Disable WPS On WAG120N?

Aug 24, 2012

Is there any way to disable WPS feature on my WAG120?

View 1 Replies View Related

Linksys Cable / DSL :: WAG120N Won't Install

Mar 31, 2011

Just bought this WAG120N and using the CD Setup it gets as far as Install Gateway then displays its not connected properly. Checked everything it says to check.Im swapping from an ordinary adsl modem but i unplugged all of that and the WAG120N shows steady Power , 1 ethernet number lit and flashing ok,  Wireless is lit and DSL is also also lit.   Rebooted a few times too.

View 1 Replies View Related

Linksys Cable / DSL :: How To Set Up WAG120N As A Router Only

Jul 20, 2011

How do I set up the WAG120N as a router only as I no longer want to use it as modem and router?I want to connect the WAG120N thru a cable to a modem that will make the internet connection and use the WAG120N as a wireless router only.

View 3 Replies View Related

Linksys Cable / DSL :: WAG120N - Want Public IP On PC

Apr 19, 2012

I have a WAG120N modem-router.What i want is to have my public IP on my pc.So... just 1 pc with 1 ip... but whatever i do... nothing works.

View 1 Replies View Related

Linksys Cable / DSL :: WAG120N - Can't Login To It And Its Quite Hot

Mar 27, 2011

I've got a new WAG120N which seems to lock up about every 24 hours. All the lights are on except the wireless light goes out. Can't login to it and its quite hot.

View 3 Replies View Related

Linksys Cable / DSL :: Connecting Laptop To WAG120N?

Jul 22, 2011

problems when I wanted to connect my laptop to my WAG120Nrouter for the first time.First the wireless adapter on my windows xp gives me the error "unable to verify your identity"second when i passed the security verification by bypassing the security options on the connection properties of the adapter, windows tries to acquiring network address and continues it for hours. Seems Windows cannot get any ip address from the router.The router works fine with wired Ethernet devices and my iPhone when i connect it wirelessly.

View 1 Replies View Related

Linksys Cable / DSL :: WAG120N - Ports Won't Open?

May 14, 2012

normally i have no trouble opening serten ports for gaming purposes but now i just cant seem to get them open
 
if i do  hyperlobby: (begin: 20999 ) (end: 21001 ) protocol: ( both) on my current ip address and select the active square
 
it should open port 21000 right?but if i check in game, it wont open, and if i check on internet for port checks it also says timed out, for some reason it wont open this port, also other game ports wont open anymore,not sure what router i got but i think this is the model :  WAG120N

View 1 Replies View Related

Linksys Cable / DSL :: Configure WAG120N As Bridge?

Jan 31, 2012

I need to configure a WAG 120 N  as a bridge, so I can have my public IP as an output of an Ethernet port. I need this configuration because I have a non ADSL router managing VPNs and needs the public IP on the WAN port of this router.

View 3 Replies View Related

Linksys Cable / DSL :: WAG120N Won't Airprint To HP Printer

Jan 24, 2011

My WAG120N does not allow airprint from ipad/ipod to HP photosmart wireless printer.  When i replace the linksys router with an old netgear one all works well and the ipad can find the printer and print.  Enable the Linksys router and the printer is no longer found on the ipad.  other forums suggest this relates to handling of the Bonjour protocol ... any resolution for this so i dont have to go back to legacy speed on my home wifi?

View 3 Replies View Related

Linksys Cable / DSL :: Slow Internet On New WAG120N

Oct 24, 2010

I have a WAG120N which runs speedtest.net at 0.1 Mbs. My old router used to get 6 Mbs.I have tried a firmware update & reset, reduced the MTU to 1300 but still no different.Windows Vista & 7 - two different computers, same speed...

View 6 Replies View Related

Linksys Cable / DSL :: Port 80 Does Not Work On DMZ With WAG120N

Nov 22, 2011

I configured my router Linksys WAG120N as DMZ, but  not forward port 80, only port 80.

View 1 Replies View Related

Linksys Cable / DSL :: No N Network Connection With WAG120N?

Mar 22, 2011

when choosing "Mixed" or "N-only" as Network Mode on the Basic Wireless Settings configuration page, the mode resets to "B/G-Mixed" or "G-only" respectively when saving. In other words, it is not possible to use the N network mode.

View 4 Replies View Related

Linksys Cable / DSL :: WAG120N Keeps Disconnected From Internet

Apr 18, 2010

I am using WAG120N, and it keeps disconnected from internet randomly, normally between 5-10 minutes. The thing is, when it is disconnected, the adsl lamp is still on, so I think that it is not the network problem. When internet lamp turns off , I try to turn off the device (or unplug the phone cable), then turn it on again (or re-plug the cable), and it will work for certain minutes, then gets disconnected again. I already upgraded the firmware to v 1.00.12. 

View 4 Replies View Related

Linksys Cable / DSL :: How To Configure WAG120N As A Modem

Apr 18, 2013

I have WAG120N and is working fine, but has very poor wifi range. I recently purchased EA 6500. how to setup my WAG120N as a modem only and shift all routing to the EA6500

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved