I recently purchased the Linksys Wireless N Home WAG120N and I've hooked it up correctly but I can't seem to establish a connection with the DSL light. I've tried hooking it up to different ends in my house with no improved results, however, my older modem works fine.
My WAG120N power light is always red whenever plugged in. I can't access the configuration page. My adapter works fine and the Reset button doesn't work. I can't find any troubleshoot for the "red power light" problem in user manual !
Yesterday I bought the Linksys Wireless-N Home ADSL2+ Modem Router WAG120N (Annex-A version). I configured the modem/router and it was working very well. Today I was surfing the internet just fine and I left my computer for a few minutes, when I came back I noticed that there is no internet connection. The internet light on the modem was no longer on, and the DSL one was blinking. I turned off the device and then turned it back on but the issue was still present. I tried restoring the factory default settings and configuring the modem again but nothing seems to work (resetting the modem, turning off every device connected to it and restarting the modem/router). The DSL light keeps blinking, turns off for a couple seconds and then starts blinking again. The internet light only appears when I restart the modem and it flashes red just after turning the device on.
I just ordered the Linksys WAG120N modem/ router and need configuring the same on the BSNL network. Any Document or link about his Installation and configuration.
Now unable to connect laptop wirelessly. The laptop can see the connection, but when I click it to connect it just doesn't. Have tried rebooting both laptop, desktop and modem, left it overnight, can't connect smartphone to it either. All were working perfectly until I had to reinstall.
I am using wag120n modem router but is confused abt how to setup it's wireless security.The wireless securit setting recommended in tutorial given here is very different from what is given in my routrs setting up page.
I don't know how to handle the key renewal option.If i leave it as 3600 seconds does that mean i have to enter a new key in my wireless device connected to the router after every 1 hour?
I am having a problem with my ea4500 several times a day the cisco light flashes and I loose internet connectivity. I have tried resetting the router by the reset button and changed ssid name, making two different one for each band, and still I am having a problem. I have read where it could be a firmware update, I have updated (using current version)
i have Linksys WRT610N V2 now i got problem the power light flashing still keep cannot use but wifi and wan and lan no light but 1 light power only still keep power flashing blinking no stable now i using adsl modem direct connected i using linksys am300 adsl modem
I have WAG120N and is working fine, but has very poor wifi range. I recently purchased EA 6500. how to setup my WAG120N as a modem only and shift all routing to the EA6500
I can't seem to setup my WAG120N modem.I kept on getting the error "your ethernet cable does not appear to be connected properly" even though I have connected all the cables correctly. I can access the modem through the browser via 192.168.1.1 though.I thought the setup is supposed to be simple but I have wasted few hours.
So I just got this new WRT160Nv2 router. I have (1) wired computer and then my laptop running wireless to it. For the first couple days I had some issues getting consistant internet but after reading some stuff on here I downgraded to the version 8 hardware and it worked GREAT for about 3 days. Now my power light won't stop flashing and I have NO internet connection at all through the router. I have tried to reset the router by holding down the button and also unpluging it but still nothing.
Is it normal for the "CISCO" icon/light to "fast flashing" periodically - not to be confused with the "slow flashing" that the E4200V2 displays when being "power cycled"?
I just purchased a new E4200 to speed up my network and all seems to be fine with the exception of the Cisco light flashing rapidly which indicates a problem.
Everything was working fine. Changed Nothing on the router. Goes out and now wont broadcast a wireless signal, cant manually reset the router, or get into the settings with 192.168.1.1
Currently I am wired through it with my desktop and its working, but not much else.
So, I messed around with my router a little too much and just want to restore it back to the original firmware now. I have a WRT54GS v7 Linksys router and tried to follow this guide to flash the firmware to something a little more useful. After step 7 of that guide, I can't ping my router, can't access the GUI, and have no idea what my router's IP is. If I assign each computer plugged into the router an IP like 192.168.1.2 I can ping them, so the router is still functioning somewhat. I'm plugged into my modem right now to get on the Internet.
Right now, my power light is off, my DMZ light is off, my WLAN light is off, but the other lights turn on if I plug a cord into its port (plug a computer into port 1, port 1's light comes on). When I do an ipconfig /all i get this. I doubt the web interface still works, but if I could at least get the router's IP, couldn't I use tftp and put the firmware on that way?
I have a 1921 router with a V.2 T1 wic installed connected to a MPLS circuit. The circuit is down hard and the CD light is flashing. We reseated the WIC card and the circuit recovered for about 30 seconds, then went down and CD began flashing again on the WIC. AL is solid.
I have a new TEW-692GR router attached to an UBEE DVM3203B cable modem. For the last several days the WAN light on the router and the LINK light on the cable modem flash on a continual basis. This seemed to happen after establishing a wireless connection between a new LG smart tv and the router but am not sure if that in fact caused the issue. I have power cycled all devices on my network in an attempt to clear this up but no joy.
We just moved into a new place a couple days ago and the cable guy (from Cox) came and hooked everything up. The cable works but I plugged in my n300 belkin wireless router and it'll have a blue ligh for a couple second then flash and then turn to flashing amber/orange. It won't connect to the Internet. I tried resetting it, unplugging from both ends and nothing will work.
How do I set up the WAG120N as a router only as I no longer want to use it as modem and router?I want to connect the WAG120N thru a cable to a modem that will make the internet connection and use the WAG120N as a wireless router only.
We are trying to play Call of Duty MW3. We have purchased two games and two xbox360s. We want to connect the two xboxs to the internet using a cisco wag120n router..
My WAG120N wireless router disconnects every hour, precisely at the same time. This problem has started a few days ago, until then everything was fine.When the connection is gone, the "Internet" light goes off, the other lights remain on. For example, it disconnects at 07:30. It takes a minute or two to reconnect. Then it disconnects at 08:31. It reconnects, and then disconnects at 09:32.. and so on.Here are the things that I have tried (with my limited knowledge.. I'm not good with technology):- Turned the power on/off. No matter what time I do this at, the router disconnects at the same time again. For example, if it last disconnected at 07:30, and I turn it off and on at 7:50, it still disconnects at 08:31.- I tried resetting it, by pushing and holding the reset button on the back for 30-60 seconds (did it several times). Reconfigured the router (manually, not from a backup config file). Same situation as above, disconnects at the same time as always.
- I upgraded the IOS to v1.00.16, which I found here: [URL] reset and then reconfigured again. Still it didn't work.- Looked in the configuration pages for any values that resemble a 60 minute time span, and changed them. Only thing I found was the security key renewal period. Or was I sold a faulty product?
My WAG120N router overheating and stuck repeatedly every 4-5 hours. How i can solve this problem? I buy this router 3-4 months ago...Is hardware or software issue?
My WAG120N: Firmware Version: V1.00.07 DDNS Service - Disable DMZ Hosting - Disable Firewall - Disable Restore to Factory Setting - Many Times = No result Connected Computers in the LAN - WLAN = 6 Desktops-Laptops, 3 PDA Devices
--> My Router gives this information about my Downstream / Upstream Rate Downstream Rate: 10229 kbps Upstream Rate: 861 kbps
I have a 3G USB modem connected to my desktop and I would like to share the internet connection to other devices wirelessly using the WAG120n ADSL router. How do I set up the IP's manually on the router and my PC to do this? And which other setting do I need to set?
I have been using it since approx 6months ago. Previously it was working well except for some major signal issues. However, 3 days ago it decided to go haywire. 1) It does not connect to the internet 2) It does not detect/connect to the computer when LAN cable is plugged in (does not load in 192.168.1.1) 3) I have tried resetting the router many times and even holding the reset button for 30 secs and switching off and switching on but to no avail. 4) I have had a linksys live chat with Johnel and he determined that it may be a possible hardware problem 5) Current Status of the Router: It makes no attempt to establish any connection/load whenever turned on, as seen when no lights are blinking when switched on. Upon switching on, Power Light becomes Red and Internet Light becomes Red and the middle Refresh Button become Red. 6) I have tried installing the driver for the router but there is no way I can install the driver because the computer does not detect that the router is connected What can I do about these? 1) Can I get a replacement of a different model? This router has been giving me problems since Day 1 2) I am seriously considering switching my service provider from M1 to Starhub. If that is the case, is there any way I can be replaced with a Cable Modem instead of ADSL Modem?
I have a linksys WAG120N router updated to 1.00.16and I have Wi-Fi problems that while I use Wi-Fi on my laptop or mobile then the Wi-Fi disconnected (wifi on router still green but i can't connect ) until i restart router.
My WAG120N router has stopped working completely. None of the Ethernet ports or the wi-fi signal button is lit,power light continues to blink for 10 odd mins and then comes to a rest. Tried to login to admin portal without any success, tried to reset it pressing the reset button in the back without any success.Tried the 30-30-30 reset method without success too.
I am using the WAG-120 N as an AP and switch for 3 laptops and 2 desktops. Our department is assigned only one Static IP from our server, so only one pc can connect to the server and the internet. I use the first lan port of the Wag-120N as a WAN port and i assign the Static IP address there, along with the subnet, default gateway and DNS addresses. The connected clients are assigned then an ip address from the router's DHCP (192.168.1.10x), but cannot connect to the internet. How can i configure the router to allow the clients to connect?
i have here Cisco 877 model, when i turn it on the CD light keep flashing,there is no connection to connect to router to configure it,i tried to connect with Consol, and UTP but no vail,i clicked the RESET button btw the consol and ADSL button unfortunatly no vail,
i just bought a sony lcd tv and this model can be controlled by a smartphone via an app called mediaremote. The app should scan the local network and find the tv and than, after pairing, you can use the smartphone as remote controller over Wi-Fi.
My problem is that the router block the network scan and the app can't find the tv; is there somethig i can chack in the configuration or that else to permit the local network scan?
I tried to connect tv and smartphone to the neighbour wifi and the app woks perfect so i'm sure that is a my network problem.
I have the cisco WAG120N router. In order to avoid constant radiation I would like to be able to connect my computer and router using an ethernet cable and if possible disconnect and use it wireless when I need more than one computers or netbooks to be connected to the internet. I tried to connect my computer with the router using an ethernet cable but I realized that I continued to have the wireless network on.
I just bought linksys EA2700 to replace my U.S Robotics .. but when i try to connect it like the old router , the internet lights won't turn on, is it because i have to use a modem then use ethernet cable ? can't i just use ADSL cable directly to the router like robotics router ? when i try to configure it manually , i change the internet type to PPoE protocol but i can't find VCI/VPI so where are they ?
I switch to a new internet provider. which is wireless[Frontier]. my printer is dell V715w the orange light is flashing. provide detailed info to correct