I just ordered the Linksys WAG120N modem/ router and need configuring the same on the BSNL network. Any Document or link about his Installation and configuration.
View 3 Replies
I have WAG120N and is working fine, but has very poor wifi range. I recently purchased EA 6500. how to setup my WAG120N as a modem only and shift all routing to the EA6500
View 2 Replies View RelatedI am using the WAG-120 N as an AP and switch for 3 laptops and 2 desktops. Our department is assigned only one Static IP from our server, so only one pc can connect to the server and the internet. I use the first lan port of the Wag-120N as a WAN port and i assign the Static IP address there, along with the subnet, default gateway and DNS addresses. The connected clients are assigned then an ip address from the router's DHCP (192.168.1.10x), but cannot connect to the internet. How can i configure the router to allow the clients to connect?
View 9 Replies View RelatedI recently purchased the Linksys Wireless N Home WAG120N and I've hooked it up correctly but I can't seem to establish a connection with the DSL light. I've tried hooking it up to different ends in my house with no improved results, however, my older modem works fine.
View 1 Replies View RelatedNow unable to connect laptop wirelessly. The laptop can see the connection, but when I click it to connect it just doesn't. Have tried rebooting both laptop, desktop and modem, left it overnight, can't connect smartphone to it either. All were working perfectly until I had to reinstall.
View 6 Replies View RelatedI am using wag120n modem router but is confused abt how to setup it's wireless security.The wireless securit setting recommended in tutorial given here is very different from what is given in my routrs setting up page.
I don't know how to handle the key renewal option.If i leave it as 3600 seconds does that mean i have to enter a new key in my wireless device connected to the router after every 1 hour?
I need to configure a WAG 120 N as a bridge, so I can have my public IP as an output of an Ethernet port. I need this configuration because I have a non ADSL router managing VPNs and needs the public IP on the WAN port of this router.
View 3 Replies View RelatedI can't seem to setup my WAG120N modem.I kept on getting the error "your ethernet cable does not appear to be connected properly" even though I have connected all the cables correctly. I can access the modem through the browser via 192.168.1.1 though.I thought the setup is supposed to be simple but I have wasted few hours.
View 1 Replies View Relatedi have 2 linksys modems wag120n and wag320n.i am using wag320n as my primary modem and i want to set up wag120n as an access point to provide internet access in another room. what should be the configuration of wag120n?and yes i have read all the post about this subject and tried it all but since there was no actual solution for this problem i decided to open a new post.
View 1 Replies View RelatedHow do I set up the WAG120N as a router only as I no longer want to use it as modem and router?I want to connect the WAG120N thru a cable to a modem that will make the internet connection and use the WAG120N as a wireless router only.
View 3 Replies View RelatedWe are trying to play Call of Duty MW3. We have purchased two games and two xbox360s. We want to connect the two xboxs to the internet using a cisco wag120n router..
View 2 Replies View RelatedMy WAG120N wireless router disconnects every hour, precisely at the same time. This problem has started a few days ago, until then everything was fine.When the connection is gone, the "Internet" light goes off, the other lights remain on. For example, it disconnects at 07:30. It takes a minute or two to reconnect. Then it disconnects at 08:31. It reconnects, and then disconnects at 09:32.. and so on.Here are the things that I have tried (with my limited knowledge.. I'm not good with technology):- Turned the power on/off. No matter what time I do this at, the router disconnects at the same time again. For example, if it last disconnected at 07:30, and I turn it off and on at 7:50, it still disconnects at 08:31.- I tried resetting it, by pushing and holding the reset button on the back for 30-60 seconds (did it several times). Reconfigured the router (manually, not from a backup config file). Same situation as above, disconnects at the same time as always.
- I upgraded the IOS to v1.00.16, which I found here: [URL] reset and then reconfigured again. Still it didn't work.- Looked in the configuration pages for any values that resemble a 60 minute time span, and changed them. Only thing I found was the security key renewal period. Or was I sold a faulty product?
My WAG120N router overheating and stuck repeatedly every 4-5 hours. How i can solve this problem? I buy this router 3-4 months ago...Is hardware or software issue?
My WAG120N:
Firmware Version: V1.00.07
DDNS Service - Disable
DMZ Hosting - Disable
Firewall - Disable
Restore to Factory Setting - Many Times = No result
Connected Computers in the LAN - WLAN = 6 Desktops-Laptops, 3 PDA Devices
--> My Router gives this information about my Downstream / Upstream Rate
Downstream Rate: 10229 kbps
Upstream Rate: 861 kbps
I have a 3G USB modem connected to my desktop and I would like to share the internet connection to other devices wirelessly using the WAG120n ADSL router. How do I set up the IP's manually on the router and my PC to do this? And which other setting do I need to set?
View 1 Replies View RelatedI have been using it since approx 6months ago. Previously it was working well except for some major signal issues. However, 3 days ago it decided to go haywire. 1) It does not connect to the internet 2) It does not detect/connect to the computer when LAN cable is plugged in (does not load in 192.168.1.1) 3) I have tried resetting the router many times and even holding the reset button for 30 secs and switching off and switching on but to no avail. 4) I have had a linksys live chat with Johnel and he determined that it may be a possible hardware problem 5) Current Status of the Router: It makes no attempt to establish any connection/load whenever turned on, as seen when no lights are blinking when switched on. Upon switching on, Power Light becomes Red and Internet Light becomes Red and the middle Refresh Button become Red. 6) I have tried installing the driver for the router but there is no way I can install the driver because the computer does not detect that the router is connected What can I do about these? 1) Can I get a replacement of a different model? This router has been giving me problems since Day 1 2) I am seriously considering switching my service provider from M1 to Starhub. If that is the case, is there any way I can be replaced with a Cable Modem instead of ADSL Modem?
View 9 Replies View RelatedI have a linksys WAG120N router updated to 1.00.16and I have Wi-Fi problems that while I use Wi-Fi on my laptop or mobile then the Wi-Fi disconnected (wifi on router still green but i can't connect ) until i restart router.
View 7 Replies View RelatedMy WAG120N router has stopped working completely. None of the Ethernet ports or the wi-fi signal button is lit,power light continues to blink for 10 odd mins and then comes to a rest. Tried to login to admin portal without any success, tried to reset it pressing the reset button in the back without any success.Tried the 30-30-30 reset method without success too.
View 3 Replies View Relatedi just bought a sony lcd tv and this model can be controlled by a smartphone via an app called mediaremote. The app should scan the local network and find the tv and than, after pairing, you can use the smartphone as remote controller over Wi-Fi.
My problem is that the router block the network scan and the app can't find the tv; is there somethig i can chack in the configuration or that else to permit the local network scan?
I tried to connect tv and smartphone to the neighbour wifi and the app woks perfect so i'm sure that is a my network problem.
have wireless d-link adsl modem router which usually use for adsl connection sharing, but i have a cable internet connection, so my question is can i share my cable internet connection with this router?
View 1 Replies View RelatedI have the cisco WAG120N router. In order to avoid constant radiation I would like to be able to connect my computer and router using an ethernet cable and if possible disconnect and use it wireless when I need more than one computers or netbooks to be connected to the internet. I tried to connect my computer with the router using an ethernet cable but I realized that I continued to have the wireless network on.
View 2 Replies View RelatedI can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?
View 1 Replies View RelatedIs there any way to disable WPS feature on my WAG120?
View 1 Replies View RelatedJust bought this WAG120N and using the CD Setup it gets as far as Install Gateway then displays its not connected properly. Checked everything it says to check.Im swapping from an ordinary adsl modem but i unplugged all of that and the WAG120N shows steady Power , 1 ethernet number lit and flashing ok, Wireless is lit and DSL is also also lit. Rebooted a few times too.
View 1 Replies View RelatedI have a WAG120N modem-router.What i want is to have my public IP on my pc.So... just 1 pc with 1 ip... but whatever i do... nothing works.
View 1 Replies View RelatedI've got a new WAG120N which seems to lock up about every 24 hours. All the lights are on except the wireless light goes out. Can't login to it and its quite hot.
View 3 Replies View Relatedproblems when I wanted to connect my laptop to my WAG120Nrouter for the first time.First the wireless adapter on my windows xp gives me the error "unable to verify your identity"second when i passed the security verification by bypassing the security options on the connection properties of the adapter, windows tries to acquiring network address and continues it for hours. Seems Windows cannot get any ip address from the router.The router works fine with wired Ethernet devices and my iPhone when i connect it wirelessly.
View 1 Replies View Relatednormally i have no trouble opening serten ports for gaming purposes but now i just cant seem to get them open
if i do hyperlobby: (begin: 20999 ) (end: 21001 ) protocol: ( both) on my current ip address and select the active square
it should open port 21000 right?but if i check in game, it wont open, and if i check on internet for port checks it also says timed out, for some reason it wont open this port, also other game ports wont open anymore,not sure what router i got but i think this is the model : WAG120N
My WAG120N does not allow airprint from ipad/ipod to HP photosmart wireless printer. When i replace the linksys router with an old netgear one all works well and the ipad can find the printer and print. Enable the Linksys router and the printer is no longer found on the ipad. other forums suggest this relates to handling of the Bonjour protocol ... any resolution for this so i dont have to go back to legacy speed on my home wifi?
View 3 Replies View RelatedI have a WAG120N which runs speedtest.net at 0.1 Mbs. My old router used to get 6 Mbs.I have tried a firmware update & reset, reduced the MTU to 1300 but still no different.Windows Vista & 7 - two different computers, same speed...
View 6 Replies View RelatedI configured my router Linksys WAG120N as DMZ, but not forward port 80, only port 80.
View 1 Replies View Relatedwhen choosing "Mixed" or "N-only" as Network Mode on the Basic Wireless Settings configuration page, the mode resets to "B/G-Mixed" or "G-only" respectively when saving. In other words, it is not possible to use the N network mode.
View 4 Replies View RelatedI am using WAG120N, and it keeps disconnected from internet randomly, normally between 5-10 minutes. The thing is, when it is disconnected, the adsl lamp is still on, so I think that it is not the network problem. When internet lamp turns off , I try to turn off the device (or unplug the phone cable), then turn it on again (or re-plug the cable), and it will work for certain minutes, then gets disconnected again. I already upgraded the firmware to v 1.00.12.
View 4 Replies View RelatedMy WAG120N power light is always red whenever plugged in. I can't access the configuration page. My adapter works fine and the Reset button doesn't work. I can't find any troubleshoot for the "red power light" problem in user manual !
View 3 Replies View Related
