I can't seem to setup my WAG120N modem.I kept on getting the error "your ethernet cable does not appear to be connected properly" even though I have connected all the cables correctly. I can access the modem through the browser via 192.168.1.1 though.I thought the setup is supposed to be simple but I have wasted few hours.
View 1 RepliesI have WAG120N and is working fine, but has very poor wifi range. I recently purchased EA 6500. how to setup my WAG120N as a modem only and shift all routing to the EA6500
View 2 Replies View Related1) I dis abled the DHCP services on modem router as i was connecting it to a belkin router and after that i cannot accesss the setup of the WAG 120N.
2)If I acces the WAG120N by Lan the internet works fine but if i acces through wirless it does not.
3)Also when ever i connect the LAN cable from BELKIN router to WAG 120N the wirless services stop as well on the BElkin router and i cant figure it out why.
I just ordered the Linksys WAG120N modem/ router and need configuring the same on the BSNL network. Any Document or link about his Installation and configuration.
View 3 Replies View RelatedI have a existing WiFi ADSL router and I have a WAG120N lying spare in my closet. I recently shifted to my room a floor above. I wanted to amplify signals as the current router is not able to beam signals that far. Hence I wanted to set this up as a WiFi repeater to have a complete coverage. I tried N number of ways but could not succeed.
View 1 Replies View RelatedI recently purchased the Linksys Wireless N Home WAG120N and I've hooked it up correctly but I can't seem to establish a connection with the DSL light. I've tried hooking it up to different ends in my house with no improved results, however, my older modem works fine.
View 1 Replies View RelatedNow unable to connect laptop wirelessly. The laptop can see the connection, but when I click it to connect it just doesn't. Have tried rebooting both laptop, desktop and modem, left it overnight, can't connect smartphone to it either. All were working perfectly until I had to reinstall.
View 6 Replies View RelatedI am using wag120n modem router but is confused abt how to setup it's wireless security.The wireless securit setting recommended in tutorial given here is very different from what is given in my routrs setting up page.
I don't know how to handle the key renewal option.If i leave it as 3600 seconds does that mean i have to enter a new key in my wireless device connected to the router after every 1 hour?
I recently switched from dsl to cable. I have a e2000 router that I would still like to use. The modem I have is a Motorola Surfboard SB6121. It has no options that I can modify. The modem has a built in DHCP server. However, I can't modify it and I don't like the ip configuration it uses. For the time being I have the modem connected to a switch which is working fine. What I would like to know is how to configure the e2000 to use the modems connection. I used PPPoE for DSL and had login information.
View 2 Replies View RelatedIs there any way to disable WPS feature on my WAG120?
View 1 Replies View RelatedJust bought this WAG120N and using the CD Setup it gets as far as Install Gateway then displays its not connected properly. Checked everything it says to check.Im swapping from an ordinary adsl modem but i unplugged all of that and the WAG120N shows steady Power , 1 ethernet number lit and flashing ok, Wireless is lit and DSL is also also lit. Rebooted a few times too.
View 1 Replies View RelatedHow do I set up the WAG120N as a router only as I no longer want to use it as modem and router?I want to connect the WAG120N thru a cable to a modem that will make the internet connection and use the WAG120N as a wireless router only.
View 3 Replies View RelatedI have a WAG120N modem-router.What i want is to have my public IP on my pc.So... just 1 pc with 1 ip... but whatever i do... nothing works.
View 1 Replies View RelatedI've got a new WAG120N which seems to lock up about every 24 hours. All the lights are on except the wireless light goes out. Can't login to it and its quite hot.
View 3 Replies View Relatedproblems when I wanted to connect my laptop to my WAG120Nrouter for the first time.First the wireless adapter on my windows xp gives me the error "unable to verify your identity"second when i passed the security verification by bypassing the security options on the connection properties of the adapter, windows tries to acquiring network address and continues it for hours. Seems Windows cannot get any ip address from the router.The router works fine with wired Ethernet devices and my iPhone when i connect it wirelessly.
View 1 Replies View Relatednormally i have no trouble opening serten ports for gaming purposes but now i just cant seem to get them open
if i do hyperlobby: (begin: 20999 ) (end: 21001 ) protocol: ( both) on my current ip address and select the active square
it should open port 21000 right?but if i check in game, it wont open, and if i check on internet for port checks it also says timed out, for some reason it wont open this port, also other game ports wont open anymore,not sure what router i got but i think this is the model : WAG120N
I need to configure a WAG 120 N as a bridge, so I can have my public IP as an output of an Ethernet port. I need this configuration because I have a non ADSL router managing VPNs and needs the public IP on the WAN port of this router.
View 3 Replies View RelatedMy WAG120N does not allow airprint from ipad/ipod to HP photosmart wireless printer. When i replace the linksys router with an old netgear one all works well and the ipad can find the printer and print. Enable the Linksys router and the printer is no longer found on the ipad. other forums suggest this relates to handling of the Bonjour protocol ... any resolution for this so i dont have to go back to legacy speed on my home wifi?
View 3 Replies View RelatedI have a WAG120N which runs speedtest.net at 0.1 Mbs. My old router used to get 6 Mbs.I have tried a firmware update & reset, reduced the MTU to 1300 but still no different.Windows Vista & 7 - two different computers, same speed...
View 6 Replies View RelatedI configured my router Linksys WAG120N as DMZ, but not forward port 80, only port 80.
View 1 Replies View Relatedwhen choosing "Mixed" or "N-only" as Network Mode on the Basic Wireless Settings configuration page, the mode resets to "B/G-Mixed" or "G-only" respectively when saving. In other words, it is not possible to use the N network mode.
View 4 Replies View RelatedI am using WAG120N, and it keeps disconnected from internet randomly, normally between 5-10 minutes. The thing is, when it is disconnected, the adsl lamp is still on, so I think that it is not the network problem. When internet lamp turns off , I try to turn off the device (or unplug the phone cable), then turn it on again (or re-plug the cable), and it will work for certain minutes, then gets disconnected again. I already upgraded the firmware to v 1.00.12.
View 4 Replies View RelatedMy WAG120N power light is always red whenever plugged in. I can't access the configuration page. My adapter works fine and the Reset button doesn't work. I can't find any troubleshoot for the "red power light" problem in user manual !
View 3 Replies View RelatedI have a WAG120N. I wish to use it as a modem only and not as a wireless router.I have another wireless router I want to use to handle network connectivity.I want the wag to be set to 10.10.1.1 and I want my router on 10.10.1.2What bridge mode do I set on my wag? Do I need a crossover cable?
View 1 Replies View RelatedAfter the upgrade in v1.00.16 Annexe A, I've a problem ADSL sync with the WAG120N, the router don't need the sync, how to back the v1.00.12 Annexe A.
View 1 Replies View RelatedDoes WAG120N Support IPv6 ?
View 1 Replies View RelatedI have multiple macs and when all of them are connected to the wag120n router, macs can't seem to find/see each other as if they are connected to different networks. I have tried another router ie. netgear dg834g router and this problem didn't occur and i am able to connect over the network without a problem. Obviously there is something wrong with the router settings.
View 2 Replies View RelatedWe have a customer who has a WAG120N as their broadband wireless router, and we've sold them some new equipment, part of which is another WAG120N as our salesperson didn't realise they had one.They have a section of the building which the current WAG120N will not reach. Reading around this forum, it seems that I can give the second WAG120N a different static IP on the LAN and use it to expand the range of the WLAN.If I've read correctly, I need to make all the wireless stuff exactly the same except to use different wireless channels on each router. But what do I do with the DHCP server on the second WAG? Is it fair to say that the clients won't suddenly jump to a different IP because they won't have a cause to request a new one? I read one comment that suggested the second should be configured for DHCP relay, and another which contradicted this. Presumably I just don't configure the ADSL on the second WAG as that will only connect to the LAN.
View 3 Replies View Relatedwhat do i need to setup in WAG120N to work with a Wireless Network repeater?
View 1 Replies View RelatedOk so for about a week now I have a problem with router. Today I checked log of router and found sometging like this:
Wed, 2012-12-26 15:41:15 - No response to 3 echo-requestsWed, 2012-12-26 15:41:15 - Serial link appears to be disconnected.Wed, 2012-12-26 15:41:15 - Enter: tdb_store.Wed, 2012-12-26 15:41:15 - tdb_store: calling tdb_update.Wed, 2012-12-26
[Code].....
Accidentally I disabled the modem web access therfore I am not able to open admin console from http://192.168.1.1. How to enable it again?
View 1 Replies View RelatedI have BSNL Broadband with speed 512 kbps. My old modem gives me speed 0.54 mb . i have checked it on speedtest.net .But my new WAG120N gives me less speed 0.15mb .Why this so happen?i checked all settings
View 1 Replies View RelatedI have a WAG 120N Modem Router, My question is: Can you assign an static IP to a pc using this router?
View 2 Replies View Related