I can't seem to setup my WAG120N modem.I kept on getting the error "your ethernet cable does not appear to be connected properly" even though I have connected all the cables correctly. I can access the modem through the browser via 192.168.1.1 though.I thought the setup is supposed to be simple but I have wasted few hours.
I have a existing WiFi ADSL router and I have a WAG120N lying spare in my closet. I recently shifted to my room a floor above. I wanted to amplify signals as the current router is not able to beam signals that far. Hence I wanted to set this up as a WiFi repeater to have a complete coverage. I tried N number of ways but could not succeed.
i have 2 linksys modems wag120n and wag320n.i am using wag320n as my primary modem and i want to set up wag120n as an access point to provide internet access in another room. what should be the configuration of wag120n?and yes i have read all the post about this subject and tried it all but since there was no actual solution for this problem i decided to open a new post.
i have a router to connect on Internet, i need it because it let me use VOIP. I want to use WAG120N like Access Point Wireless because my VOIP router is not wireless.
How i have to configure it? What kind of incapsulation i have to use? VOIP router IP: 192.168.1.1
If is it possible (and if it is useful) i would to configure WAG120N with 2 IP, first one: 192.168.1.101 (to communicate with VOIP router and to let me go on internet) second one: 192.168.0.1 (to let me have control on it's configuration)
I have 2 Router (Cisco WAG120N) and (Micronet SP3364)I am connected to the Internet with MicronetUse Cisco Only ACCESS PointI am putting Cisco on a bridge and OnlyBut I am having problem ... Cisco is always disconnected, but I have internet on the wireless network through the Cisco.
I am connected to internet via a cable modem, via the LAN cable, I connect cable modem to WAG120N that I want to use as an wireless access point only. And I have got 2 PC, 1 runs on XP, the other on runs on Windows 7. My XP would have no trouble to connect to wireless, but the Win7 can only connect to wireless network, but no internet. When I try the troubleshooting from Win 7, it says, DNS server isnt responding The setting I am using at the moment is Bridged mode only, without entering any values of DNS, IP, etc Is there any setting that work for both OS?
Recently I shifted to ADSL2+ Internet broadband.So purchased "CISCO Linksys WAG120N" router as my firewall hardware( FortiGate60) had no any port to connect to ADSL.Now I'm accessing internet throug the above Linksys router and do not use the firewall as I don't know how to configure the firewall to get the internet access through firewall from the router.My earlier broadband service was directly connected to the firewall's WAN port as it was compatible.configure the firewall to access the internet from the router through the firewall.
I have local WI-Fi network with 2 Macs, 2 PC's, iPhone, iPod and i Pad at home on Link sys WAG120N router. On i Pad when I try to connect to Internet I have to turn WiFi off and on. It works for a while but after waking i Pad from sleep I have to switch off and on again. It really drives me crazy. Sometimes (hardly ever) it happens on my iPhone 4 (same network setup as on i Pad). Other devices connect to Internet whenever I need.
It has been 4 months my Router " Wag 120n ". The Router Gives Me A yellow Sign on the network Icon Sying " No network Access " and the wireless Led is blinking with 1 sec interval So
- I cant open Router's Home Page - there is No ping to 192.168.1.1 " General Failure or Host unreachable " response - The Only way to get connected again is to replug the router from electricity , it works normally for 5 min and the Yellow Sign shows up again
the Solutions I Tried to fix that up :-
1) Hard reset the 30/30/15 reset 2) Firmware re-flashing 3) Trying an old firmware 126.96.36.199 instead of 188.8.131.52
but nothing of those worked the Only thing that worked for like 20 min the firmware upgrade but after that the problem came up again the problem happens to all Computers on the network wired or on wireless happens on all kind of operations systems win7, xp, vista, (Android for mobiles).
I am connecting to the internet in two desktops using the WAG120N modem+router.I have no problems with the internet. But when I try to use the wireless access point in my mobile phone / laptop,the device is not able to find the WiFi access point. I need to swith off the modem and start it again, then the devices are finding the access point. I guess this has to do with some amount of inactivity and the modem switces off the wireless access point. I there anyway by which I can turn off that setting ? I have tried the setting page but was not able to find anything.
Just bought this WAG120N and using the CD Setup it gets as far as Install Gateway then displays its not connected properly. Checked everything it says to check.Im swapping from an ordinary adsl modem but i unplugged all of that and the WAG120N shows steady Power , 1 ethernet number lit and flashing ok, Wireless is lit and DSL is also also lit. Rebooted a few times too.
How do I set up the WAG120N as a router only as I no longer want to use it as modem and router?I want to connect the WAG120N thru a cable to a modem that will make the internet connection and use the WAG120N as a wireless router only.
I'm trying to set up access restrictions to specify the full url on my WAG200G (firmware 1.00.07). In particular to block a few specific https:// sites without blocking all https://. It it easy with http:// If I try https://blah.com it throws back an error invalid url.
I tried already several times, may be I entered already a name and password, can`t remember. Anyhow this time I was well documented to start again, but after 192.168.1.1, leaving 'name' blank, and password 'admin', this was quoted as wrong name and/or password. What to do to be able to continue now?
problems when I wanted to connect my laptop to my WAG120Nrouter for the first time.First the wireless adapter on my windows xp gives me the error "unable to verify your identity"second when i passed the security verification by bypassing the security options on the connection properties of the adapter, windows tries to acquiring network address and continues it for hours. Seems Windows cannot get any ip address from the router.The router works fine with wired Ethernet devices and my iPhone when i connect it wirelessly.
normally i have no trouble opening serten ports for gaming purposes but now i just cant seem to get them open
if i do hyperlobby: (begin: 20999 ) (end: 21001 ) protocol: ( both) on my current ip address and select the active square
it should open port 21000 right?but if i check in game, it wont open, and if i check on internet for port checks it also says timed out, for some reason it wont open this port, also other game ports wont open anymore,not sure what router i got but i think this is the model : WAG120N
I need to configure a WAG 120 N as a bridge, so I can have my public IP as an output of an Ethernet port. I need this configuration because I have a non ADSL router managing VPNs and needs the public IP on the WAN port of this router.
My WAG120N does not allow airprint from ipad/ipod to HP photosmart wireless printer. When i replace the linksys router with an old netgear one all works well and the ipad can find the printer and print. Enable the Linksys router and the printer is no longer found on the ipad. other forums suggest this relates to handling of the Bonjour protocol ... any resolution for this so i dont have to go back to legacy speed on my home wifi?
I have a WAG120N which runs speedtest.net at 0.1 Mbs. My old router used to get 6 Mbs.I have tried a firmware update & reset, reduced the MTU to 1300 but still no different.Windows Vista & 7 - two different computers, same speed...
when choosing "Mixed" or "N-only" as Network Mode on the Basic Wireless Settings configuration page, the mode resets to "B/G-Mixed" or "G-only" respectively when saving. In other words, it is not possible to use the N network mode.
I am using WAG120N, and it keeps disconnected from internet randomly, normally between 5-10 minutes. The thing is, when it is disconnected, the adsl lamp is still on, so I think that it is not the network problem. When internet lamp turns off , I try to turn off the device (or unplug the phone cable), then turn it on again (or re-plug the cable), and it will work for certain minutes, then gets disconnected again. I already upgraded the firmware to v 1.00.12.
My WAG120N power light is always red whenever plugged in. I can't access the configuration page. My adapter works fine and the Reset button doesn't work. I can't find any troubleshoot for the "red power light" problem in user manual !
I have a WAG120N. I wish to use it as a modem only and not as a wireless router.I have another wireless router I want to use to handle network connectivity.I want the wag to be set to 10.10.1.1 and I want my router on 10.10.1.2What bridge mode do I set on my wag? Do I need a crossover cable?