Linksys Cable / DSL :: Configuring WAG120N Like Access Point?
May 17, 2010
i have a router to connect on Internet, i need it because it let me use VOIP. I want to use WAG120N like Access Point Wireless because my VOIP router is not wireless.
How i have to configure it? What kind of incapsulation i have to use? VOIP router IP: 192.168.1.1
If is it possible (and if it is useful) i would to configure WAG120N with 2 IP, first one: 192.168.1.101 (to communicate with VOIP router and to let me go on internet) second one: 192.168.0.1 (to let me have control on it's configuration)
My devices will connect to 192.168.0.0 network
View 9 Replies
ADVERTISEMENT
Feb 2, 2012
i have 2 linksys modems wag120n and wag320n.i am using wag320n as my primary modem and i want to set up wag120n as an access point to provide internet access in another room. what should be the configuration of wag120n?and yes i have read all the post about this subject and tried it all but since there was no actual solution for this problem i decided to open a new post.
View 1 Replies
View Related
Mar 23, 2013
I have had trouble setting my WAG120N as router.
I am connected to internet via a cable modem, via the LAN cable, I connect cable modem to WAG120N that I want to use as an wireless access point only. And I have got 2 PC, 1 runs on XP, the other on runs on Windows 7. My XP would have no trouble to connect to wireless, but the Win7 can only connect to wireless network, but no internet. When I try the troubleshooting from Win 7, it says, DNS server isnt responding The setting I am using at the moment is Bridged mode only, without entering any values of DNS, IP, etc Is there any setting that work for both OS?
View 1 Replies
View Related
Dec 17, 2011
I am connecting to the internet in two desktops using the WAG120N modem+router.I have no problems with the internet. But when I try to use the wireless access point in my mobile phone / laptop,the device is not able to find the WiFi access point. I need to swith off the modem and start it again, then the devices are finding the access point. I guess this has to do with some amount of inactivity and the modem switces off the wireless access point. I there anyway by which I can turn off that setting ? I have tried the setting page but was not able to find anything.
View 6 Replies
View Related
Feb 14, 2012
I have a Linksys WAG120N Wireless-N ADSL2+ Modem Router. The firmware version is V1.00.12.I run a Windows machine attached to the router which has a certain sub network address. On that same machine I run a Virtual Machine with Linux which has its own address, 192.168.1.102. I've been noticing that whenever I shut down either machine and then turn them back on later, they acquire another address, which makes it annoying for me to make them communicate between each other (by, for example, trying to load a webpage hosted on the VM from the physical machine) without knowing the actual address, which, as I said earlier, seems to change every time.
I'd like to know if there's a way (with my router model) to configure it so that the sub network address of both machines remains the same, no matter whether or not they've been shut down and restarted.
View 4 Replies
View Related
Dec 21, 2012
I need a wifi extender for wag 120n , and i want to connect it with WDSI use wag 120n as main and only modem and access pointWhat is the best and cheapest device for me?
View 1 Replies
View Related
Oct 3, 2011
1) I dis abled the DHCP services on modem router as i was connecting it to a belkin router and after that i cannot accesss the setup of the WAG 120N.
2)If I acces the WAG120N by Lan the internet works fine but if i acces through wirless it does not.
3)Also when ever i connect the LAN cable from BELKIN router to WAG 120N the wirless services stop as well on the BElkin router and i cant figure it out why.
View 1 Replies
View Related
Jan 20, 2012
Accidentally I disabled the modem web access therfore I am not able to open admin console from http://192.168.1.1. How to enable it again?
View 1 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Jul 18, 2011
I have 2 Router (Cisco WAG120N) and (Micronet SP3364)I am connected to the Internet with MicronetUse Cisco Only ACCESS PointI am putting Cisco on a bridge and OnlyBut I am having problem ... Cisco is always disconnected, but I have internet on the wireless network through the Cisco.
View 2 Replies
View Related
Dec 12, 2011
Recently I shifted to ADSL2+ Internet broadband.So purchased "CISCO Linksys WAG120N" router as my firewall hardware( FortiGate60) had no any port to connect to ADSL.Now I'm accessing internet throug the above Linksys router and do not use the firewall as I don't know how to configure the firewall to get the internet access through firewall from the router.My earlier broadband service was directly connected to the firewall's WAN port as it was compatible.configure the firewall to access the internet from the router through the firewall.
View 2 Replies
View Related
Dec 26, 2010
I have local WI-Fi network with 2 Macs, 2 PC's, iPhone, iPod and i Pad at home on Link sys WAG120N router. On i Pad when I try to connect to Internet I have to turn WiFi off and on. It works for a while but after waking i Pad from sleep I have to switch off and on again. It really drives me crazy. Sometimes (hardly ever) it happens on my iPhone 4 (same network setup as on i Pad). Other devices connect to Internet whenever I need.
View 9 Replies
View Related
Aug 3, 2012
It has been 4 months my Router " Wag 120n ". The Router Gives Me A yellow Sign on the network Icon Sying " No network Access " and the wireless Led is blinking with 1 sec interval So
- I cant open Router's Home Page
- there is No ping to 192.168.1.1 " General Failure or Host unreachable " response
- The Only way to get connected again is to replug the router from electricity , it works normally for 5 min and the Yellow Sign shows up again
the Solutions I Tried to fix that up :-
1) Hard reset the 30/30/15 reset
2) Firmware re-flashing
3) Trying an old firmware 1.0.0.12 instead of 1.0.0.16
but nothing of those worked the Only thing that worked for like 20 min the firmware upgrade but after that the problem came up again the problem happens to all Computers on the network wired or on wireless happens on all kind of operations systems win7, xp, vista, (Android for mobiles).
View 3 Replies
View Related
Nov 14, 2011
how to set up a WAP54G v3.1 Access Point if you've misplaced the CD?
View 5 Replies
View Related
Mar 26, 2012
We have network that uses a Cisco router and use a WAP54G to access the network wirelessly.
We use static IP address so if someone wants to use the wireless an IP address has to be assigned to it and be manually configured for IP Address, Gateway, Sub Net Mask and DNS.
This is becoming unwieldly, but it is safe. Is there any way to config the WAP54G as a router that would automatically assign an IP address in a range just for wireless devices.
Therefore the wireless devices could be set up as DHCP and we would use WPA/WPA2 encryption with a passkey, instead of just assigning static IP addresses.
View 1 Replies
View Related
Mar 21, 2011
I have a rental property with 3 apartments that are sharing the same internet connection. The users are consistantly downloading more than their monthly allowance, and I would like to monitor how much data each apartment's users are downloading.My plan is to purchase a Cisco WAP2000 Access Point and configure 3 SSIDs (one for each apartment). I havent decided if each SSID is to be setup on it's own VLAN.
Will I be able to use SNMP to monitor the data that each SSID has downloaded each month? I am happy to use a network management software package (such as PRTG from Paessler) for the actual monitoring itself, but I just need to know if the SNMP in the WAP2000 Access Point will provide the information to begin with.
View 1 Replies
View Related
Apr 26, 2013
Having some problems connecting up my "new" AP My current set-up consists of a Netgear "Virgin Superhub" cable modem/wireless router, a ZyXEL WRE2205 (repeater) in the hall on the first floor, and Ethernet connections through to a number of rooms, including the loft. I can't get wireless access in the loft, and I want to put the AP up there, connected through Ethernet. I want to use the same SSID and security for the AP as on the router and repeater so I can roam around(!) That's possible isn't it?What I've done so far (which hasn't worked) is connected via laptop to AP, set AP into AP mode(!), set the AP to dynamic IP, set the SSID / security the same as the router/repeater, plugged the AP into the Ethernet and tried to connect.
View 7 Replies
View Related
May 28, 2011
I just purchased 2 E2000 routers at BB and was assured the second one could be configured as a repeater access point. Some current messages indicate this is not possible.Will a Cisco moderator please confirm and clarify repeater options.
View 2 Replies
View Related
May 20, 2012
I have d-link wireless router which is connected to the internet, also I have Linksys (WAG160Nv2) which i want to use it as access point by link it to D-link router using ethernet cable in order to use the wireless internet. D-link router settings shown below
I changed the settings of linksys router as shown below
View 8 Replies
View Related
Dec 14, 2010
I have to change ISP, as mine is closing down , and the new ISP will be sending a N router - which may have 5Gh - so I'm thinking of replacng a "G" AP with the WAG320N and use the 5Ghz range. The WAG320N will be used with a USB Music harddrive and a TV and PVR connected to it - so my music will be direct to the DLNA devices - and also provide any devices with a 5Ghz signal
View 9 Replies
View Related
Jun 30, 2011
I have two routers and was wondering if it is possible to use one as a router and one as an Access point, do you know if this is possible and how do i go about configuring this?
Currently my wagN160N v2 is the one that my dsl is connected to, but how do i go about sharing this to my other router and making the WAG160n v1 the access point?
View 1 Replies
View Related
Dec 26, 2012
Is it possile make a bridge with my WAG54G2 and another Access Point ?
View 1 Replies
View Related
Jan 30, 2012
I have no clue what kind of brand is the outdoor antenna. It plugs into a wap54g and I need an extension cable to my antenna, only like 6 feet, where can i buy this?
View 1 Replies
View Related
Mar 15, 2009
i'm facing a big problem with my access point WAG54G ver 2.0 ,i just bought it from 2 days but i find alot of problems when i start using it ,i have read all the user guide and the quick install to see how to setup the access point and make it work with my adsl.i have configured all things right using PPPOE and putting my user name and password and then save settings then go to the status and press on connect , but it don't connect with me just i find connecting and adsl link : Down and still making connecting and nothing after that and my adsl led is off haven't any colors ,and when i get again to basic setup i found the password that i put it in the ppoe login is too long , not my password i tried to see what is this password and recover the hidden i found it " d6nw5vlx2pc7st9m ".i don't know what is the problem i tried alot of times to change setting and also the same problem.i think that it's a frim ware problem and i tried install a new updated frimware but everytime trying to install it get installing and suddenly stoped and white page appeard and all the access point is stopping and when restart it the ac power.
View 3 Replies
View Related
Aug 24, 2012
Is there any way to disable WPS feature on my WAG120?
View 1 Replies
View Related
Mar 31, 2011
Just bought this WAG120N and using the CD Setup it gets as far as Install Gateway then displays its not connected properly. Checked everything it says to check.Im swapping from an ordinary adsl modem but i unplugged all of that and the WAG120N shows steady Power , 1 ethernet number lit and flashing ok, Wireless is lit and DSL is also also lit. Rebooted a few times too.
View 1 Replies
View Related
Jul 20, 2011
How do I set up the WAG120N as a router only as I no longer want to use it as modem and router?I want to connect the WAG120N thru a cable to a modem that will make the internet connection and use the WAG120N as a wireless router only.
View 3 Replies
View Related
Apr 19, 2012
I have a WAG120N modem-router.What i want is to have my public IP on my pc.So... just 1 pc with 1 ip... but whatever i do... nothing works.
View 1 Replies
View Related
Mar 27, 2011
I've got a new WAG120N which seems to lock up about every 24 hours. All the lights are on except the wireless light goes out. Can't login to it and its quite hot.
View 3 Replies
View Related
Sep 15, 2009
I have a DLG-4500 router as my primary router and want to connect a second router (DIR-655) to it as an extention of the LAN to the second floor of my home. I have found instructions on doing this with most other routers, but not DLINK. In fact when doing the initial configuration and trying to disable the WAN link on the second router by using a bogus IP address string (127.0.0.1) The router won't let me save the change? What are the steps for configuring a secondary router cascaded to the primary (both wireless) to extend network coverage.
View 13 Replies
View Related
Jul 22, 2011
problems when I wanted to connect my laptop to my WAG120Nrouter for the first time.First the wireless adapter on my windows xp gives me the error "unable to verify your identity"second when i passed the security verification by bypassing the security options on the connection properties of the adapter, windows tries to acquiring network address and continues it for hours. Seems Windows cannot get any ip address from the router.The router works fine with wired Ethernet devices and my iPhone when i connect it wirelessly.
View 1 Replies
View Related
May 14, 2012
normally i have no trouble opening serten ports for gaming purposes but now i just cant seem to get them open
if i do hyperlobby: (begin: 20999 ) (end: 21001 ) protocol: ( both) on my current ip address and select the active square
it should open port 21000 right?but if i check in game, it wont open, and if i check on internet for port checks it also says timed out, for some reason it wont open this port, also other game ports wont open anymore,not sure what router i got but i think this is the model : WAG120N
View 1 Replies
View Related
Jan 31, 2012
I need to configure a WAG 120 N as a bridge, so I can have my public IP as an output of an Ethernet port. I need this configuration because I have a non ADSL router managing VPNs and needs the public IP on the WAN port of this router.
View 3 Replies
View Related
